®
INA156
©1999 Burr-Brown Corporation PDS-1565A Printed in U.S.A. December, 1999
FEATURES
●RAIL-TO-RAIL OUTPUT SWING: Within 20mV
●LOW OFFSET DRIFT: ±5µV/°C
●INTERNAL FIXED GAIN = 10V/V OR 50V/V
●SPECIFIED TEMPERATURE RANGE:
–55°C to +125°C
●LOW INPUT BIAS CURRENT: 1pA
●WIDE BANDWIDTH: 550kHz in G = 10
●HIGH SLEW RATE: 6.5V/µs
●LOW COST
●TINY MSOP-8 PACKAGES
Single-Supply, Rail-to-Rail Output, CMOS
INSTRUMENTATION AMPLIFIER
DESCRIPTION
The INA156 is a low-cost CMOS instrumentation
amplifier with rail-to-rail output swing optimized for
low-voltage, single-supply operation.
Wide bandwidth (550kHz in G = 10) and high slew
rate (6.5V/µs) make the INA156 suitable for driving
sampling A/D converters as well as general purpose
and audio applications. Fast settling time allows use
with higher speed sensors and transducers, and rapid
scanning data acquisition systems.
APPLICATIONS
●INDUSTRIAL SENSOR AMPLIFIERS:
Bridge, RTD, Thermocouple, Flow, Position
●MEDICAL EQUIPMENT:
ECG, EEG, EMG Amplifiers
●DRIVING A/D CONVERTERS
●PCMCIA CARDS
●AUDIO PROCESSING
●COMMUNICATIONS
●TEST EQUIPMENT
●
LOW COST AUTOMOTIVE INSTRUMENTATION
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
For most current data sheet and other product
information, visit www.burr-brown.com
Gain can be set to 10V/V or 50V/V by pin strapping.
Gains between these two values can be obtained with
the addition of a single resistor. The INA156 is fully
specified over the supply range of +2.7V to +5.5V.
The INA156 is available in an MSOP-8 surface-mount
package specified for operation over the temperature
range –55°C to 125°C.
22.2kΩ200kΩ
V
IN
–
V
IN
+
Ref
R
G
INA156
V
O
22.2kΩ
5kΩ5kΩ
200kΩ
R
G
V+
V–
1
5
2
3
87
4
6
A1
A2
G = 10 pins open
G = 50 pins connected
V
O
= (V
IN
– V
IN
) • G + V
REF
+–
INA156
SBOS119
2
®
INA156
SPECIFICATIONS: VS = +2.7V to +5.5V
Boldface limits apply over the specified temperature range, TA = –55°C to +125°C
At TA = +25°C, RL = 10kΩ connected to VS/2. RG pins open (G = 10), and Ref = VS/2, unless otherwise noted.
INA156E, A
PARAMETER CONDITION MIN TYP MAX UNITS
INPUT
Offset Voltage, RTI VOS VS = +5.0V, VCM = VS/2 ±2.5 ±8mV
Over Temperature
±
9mV
Drift dVOS/dT
±
5µV/°C
vs Power Supply PSRR VS = +2.7V to +6V, VCM = 0.2 • VS±50 ±200 µV/V
Over Temperature
±
250 µV/V
vs Time ±0.4 µV/mo
INPUT VOLTAGE RANGE
Safe Input Voltage (V–) – 0.5 (V+) + 0.5 V
Common-Mode Range(1) VCM VS = 5.5V 0.3 5.2(2) V
VS = 2.7V 0.2 2.5(2) V
Common-Mode Rejection Ratio CMRR VS = 5.5V, 0.6V < VCM < 3.7V, G = 10 66 78 dB
Over Temperature 65 dB
V
S
= 5.5V, 0.6V < V
CM
< 3.7V, G = 50
74 87 dB
Over Temperature 73 dB
INPUT IMPEDANCE
Differential 1013 || 3 Ω || pF
Common-Mode 1013 || 3 Ω || pF
INPUT BIAS CURRENT
Input Bias Current IB±1±10 pA
Offset Current IOS ±1±10 pA
NOISE, RTI RS = 0Ω, G = 10 or 50
Voltage Noise: f = 0.1Hz to 10Hz 4.5 µV/Vp-p
Voltage Noise Density: f = 10Hz 260 nV/√Hz
f = 100Hz 99 nV/√Hz
f = 1kHz 40 nV/√Hz
Current Noise: f = 1kHz 2 fA/√Hz
GAIN 10 50 V/V
Gain Equation G = 10 + 400kΩ/(10kΩ + RG) V/V
Gain Error(3)
VS = 5.5V, VO = 0.02V to 5.48V, G = 10
±0.08 ±0.4 %
vs Temperature
±
2
±
10 ppm/°C
VS = 5.5V, VO = 0.05V to 5.45V, G = 50 ±0.1 ±0.8
%
vs Temperature
±
15
±
30 ppm/°C
Nonlinearity
VS = 5.5V, G = 10 or 50 ±0.005 ±
0.015 % of FSR
Over Temperature
±
0.015 % of FSR
OUTPUT
Voltage Output Swing from Rail G = 10, RL = 10kΩ, GERR < 0.4% 5 20 mV
Over Temperature 20 mV
Short-Circuit Current Short-Circuit to Ground ±50 mA
Capacitance Load (stable operation) See Typical Curve
FREQUENCY RESPONSE
Bandwidth, –3dB BW G = 10 550 kHz
G = 50 110 kHz
Slew Rate SR VS = 5.5V, CL = 100pF 6.5 V/µs
Settling Time: 0.1% tS
VS = 5.5V, VO = 2V Step, CL = 100pF, G = 10
5µs
VS = 5.5V, VO = 2V Step, CL = 100pF, G = 50
11 µs
0.01%
VS = 5.5V, VO = 2V Step, CL = 100pF, G = 10
8µs
VS = 5.5V, VO = 2V Step, CL = 100pF, G = 50
15 µs
Overload Recovery 50% Input Overload 0.2 µs
Total Harmonic Distortion + Noise THD+N See Typical Curve
POWER SUPPLY
Specified Voltage Range +2.7 +5.5 V
Operating Voltage Range
+2.5 to +6
V
Quiescent Current VIN = 0, IO = 0 1.8 2.5 mA
Over Temperature VIN = 0, IO = 0 3.2 mA
TEMPERATURE RANGE
Specified Range –55 +125 °C
Operating Range –65 +150 °C
Storage Range –65 +150 °C
Thermal Resistance
θ
JA
MSOP-8 Surface Mount 150 °C/W
SO-8 Surface Mount 150 °C/W
NOTES: (1) For further information, refer to typical performance curves on common-mode input range. (2) Operation beyond (V+) – 1.8V (max) results in reduced common-mode
rejection. See discussion and Figure 6 in the text of this data sheet. (3) Does not include error and TCR of additional optional gain-setting resistor in series with RG, if used.
3
®
INA156
PIN CONFIGURATION ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
Top View MSOP
Supply Voltage, V+ to V–................................................................... 7.5V
Signal Input Terminals, Voltage(2) .................. (V–) – 0.5V to (V+) + 0.5V
Current(2) .................................................... 10mA
Output Short-Circuit(3) .............................................................. Continuous
Operating Temperature ..................................................–65°C to +150°C
Storage Temperature .....................................................–65°C to +150°C
Junction Temperature.................................................................... +150°C
Lead Temperature (soldering, 10s)............................................... +300°C
NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may degrade
device reliability. These are stress ratings only, and functional operation of the
device at these or any other conditions beyond those specified is not implied.
(2) Input terminals are diode-clamped to the power supply rails. Input signals
that can swing more that 0.5V beyond the supply rails should be current limited
to 10mA or less. (3) Short circuit to ground.
ABSOLUTE MAXIMUM RATINGS(1)
PACKAGE SPECIFIED
DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT
PRODUCT PACKAGE NUMBER RANGE MARKING NUMBER(1) MEDIA
INA156 EA MSOP-8 337 –55°C to +125°C A56 INA156EA/250 Tape and Reel
"""""INA156EA/2K5 Tape and Reel
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces
of “INA156EA/2K5” will get a single 2500-piece Tape and Reel.
PACKAGE/ORDERING INFORMATION
R
G
V
IN
V
IN
V–
R
G
V+
V
OUT
Ref
1
2
3
4
8
7
6
5
INA156
+
–
4
®
INA156
TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = 5.5V, RL = 10kΩ connected to VS/2. RG pins open (G = 10), and Ref = VS/2, unless otherwise noted.
GAIN vs FREQUENCY
Frequency (Hz)
Gain (dB)
1 10010 1k 10k 1M 10M
40
35
30
25
20
15
10
5
0100k
G = 50
G =10
COMMON-MODE REJECTION RATIO vs FREQUENCY
Frequency (Hz)
CMRR (dB)
0.1 1 10 10k 100k
100
90
80
70
60
50
40
30
20
10
0100 1k
G = 50
G = 10
POWER SUPPLY REJECTION RATIO vs FREQUENCY
Frequency (Hz)
PSRR (dB)
1 10 10k 100k 1M
100
90
80
70
60
50
40
30
20
10
0100 1k
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
Frequency (Hz)
Maximum Output Voltage (Vp-p)
1 10 10k 100k 1M
6
5
4
3
2
1
0100 1k
V
S
= 5.5V
SHORT-CIRCUIT CURRENT AND QUIESCENT CURRENT
vs POWER SUPPLY
Supply Voltage (V)
ISC (mA)
2.5 34.03.5
55
50
45
40
35
30
25
IQ (mA)
2.1
2.0
1.9
1.8
1.7
1.6
1.5
4.5 5.5 6 5
IQ
+ISC
–ISC
QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENT
vs TEMPERATURE
Temperature (°C)
I
Q
(mA)
I
SC
(mA)
75 –50 0–25
2.5
2.0
1.5
1.0
0.5
0
100
80
60
40
20
025 100 125 15050 75
I
Q
+I
SC
–I
SC
5
®
INA156
TYPICAL PERFORMANCE CURVES (Cont.)
At TA = +25°C, VS = 5.5V, RL = 10kΩ connected to VS/2. RG pins open (G = 10), and Ref = VS/2, unless otherwise noted.
0.1Hz TO 10Hz VOLTAGE NOISE
500ms/div
1µV/div
Input-Referred
INPUT VOLTAGE AND CURRENT NOISE DENSITY
vs FREQUENCY
Frequency (Hz)
Voltage Noise (nV/√Hz)
0.1 110
10k
1k
100
10
100
10
1
0.1
100 100k1k 10k
Current Noise (fA/√Hz)
e
n
i
n
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
1
0.1
0.01
0.001
THD+N (%)
10 100 10k1k
Frequency (Hz)
R
L
= 600Ω
R
L
= 600ΩR
L
= 10kΩ
R
L
= 2kΩ
G = 50
G = 10
R
L
=10kΩ
R
L
= 2kΩ
SLEW RATE vs TEMPERATURE
Temperature (°C)
Slew Rate (V/µs)
75 –50 0–25
10
9
8
7
6
5
4
3
2
1
025 100 125 15050 75
SLEW RATE vs POWER SUPPLY
Supply Voltage (V)
Slew Rate (Vµs)
2.5 343.5
7
6.5
6
5.5
5
4.5
44.5 65 5.5
INPUT BIAS CURRENT vs TEMPERATURE
Temperature (°C)
Input Bias Current (pA)
–75 –50 –25 0
10k
1k
100
10
1
0.1 25 100 125 15050 75
6
®
INA156
TYPICAL PERFORMANCE CURVES (Cont.)
At TA = +25°C, VS = 5.5V, RL = 10kΩ connected to VS/2. RG pins open (G = 10), and Ref = VS/2, unless otherwise noted.
5µs/div
100mV/div
SMALL-SIGNAL STEP RESPONSE
G = 10, CL = 100pF, RL = 10kΩ
5µs/div
100mV/div
SMALL-SIGNAL STEP RESPONSE
G = 50, CL = 100pF, RL = 10kΩ
OVERSHOOT vs LOAD CAPACITANCE
Load Capacitance (pF)
Overshoot (%)
10 100 10k
60
50
40
30
20
10
01k
G = 10
G = 50
SETTLING TIME vs LOAD CAPACITANCE
Load Capacitance (pF)
Settling Time (µs)
10 100 10k
20
18
16
14
12
10
8
6
4
2
01k
0.01%, G = 50
0.1%, G = 50
0.01%, G = 10
0.1%, G = 10
V
OS
TYPICAL
PRODUCTION DISTRIBUTION
Production Distribution (%)
Offset Voltage (mV)
–10
–8
–6
–4
–2
0
2
4
6
8
10
18
16
14
12
10
8
6
4
2
0
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
Percent of Amplifiers (%)
Offset Voltage Drift (µV/°C)
–20
–18
–16
–14
–12
–10
–8
–6
–4
–2
0
2
4
6
8
10
12
14
16
18
20
18
16
14
12
10
8
6
4
2
0
7
®
INA156
TYPICAL PERFORMANCE CURVES (Cont.)
At TA = +25°C, VS = 5.5V, RL = 10kΩ connected to VS/2. RG pins open (G = 10), and Ref = VS/2, unless otherwise noted.
1µs/div
1V/div
LARGE-SIGNAL STEP RESPONSE
G = 10, G = 50, CL = 100pF, RL = 10kΩ
INPUT COMMON-MODE RANGE
vs OUTPUT VOLTAGE, G = 50
V
OUT
(V)
V
CM
(V)
00.5 1 21.5
6
5
4
3
2
1
02.5 5.53 3.5 4 4.5 5
Ref = 0V Ref = 2.75V Ref = 5.5V
G = 50
0.9V– + 0.04V
OUT
+ 0.06Ref < V
CM
< 0.9V
+
+ 0.04V
OUT
+ 0.06Ref
INPUT COMMON-MODE RANGE
vs REFERENCE VOLTAGE, G = 10
V
REF
(V)
V
CM
(V)
00.5 1 21.5
6
5
4
3
2
1
02.5 5.53 3.5 4 4.5 5
G = 10
0.9V
–
+ 0.1Ref < V
CM
< 0.9V
+
+ 0.1Ref
COMMON-MODE REJECTION RATIO
PRODUCTION DISTRIBUTION
Production Distribution (%)
CMRR (µV/V)
G = 10
80dB
–500
–450
–400
–350
–300
–250
–200
–150
–100
–50
0
50
100
150
200
250
300
350
400
450
500
9
8
7
6
5
4
3
2
1
0
COMMON-MODE REJECTION RATIO
PRODUCTION DISTRIBUTION
Production Distribution (%)
CMRR (µV/V)
G = 50
–200
–180
–160
–140
–120
–100
–80
–60
–40
–20
0
20
40
60
80
100
120
140
160
180
200
10
9
8
7
6
5
4
3
2
1
0
80dB
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
Output Current (mA)
Output Voltage (V)
5
4
3
2
1
00 102030405060708090100
+125°C +25°C–55°C
+125°C+25°C–55°C
8
®
INA156
APPLICATIONS INFORMATION
Figure 1 shows the basic connections required for operation
of the INA156. Applications with noisy or high impedance
power supplies may require decoupling capacitors close to
the device pins, as shown.
The output is referred to the output reference terminal, Ref,
which is normally set to VS/2. This must be a low-imped-
ance connection to ensure good common-mode rejection.
In addition, for the G = 50 configuration, the connection
between pins 1 and 8 must be low-impedance. A connection
impedance of 20Ω can cause a 0.2% shift in gain error.
OPERATING VOLTAGE
The INA156 is fully specified and guaranteed over the supply
range +2.7V to +5.5V, with key parameters guaranteed over
the temperature range of –55°C to +125°C. Parameters that
vary significantly with operating voltages, load conditions or
temperature are shown in the Typical Performance Curves.
The INA156 can be operated from either single or dual
power supplies. By adjusting the voltage applied to the
reference terminal, the input common-mode voltage range
and the output range can be adjusted within the bounds
shown in the Typical Performance Curves. Figure 2 shows
a bridge amplifier circuit operated from a single +5V power
supply. The bridge provides a relatively small differential
voltage on top of an input common-mode voltage near 2.5V.
FIGURE 1. Basic Connections.
FIGURE 2. Single-Supply Bridge Amplifier.
Ref 22.2kΩ200kΩ
5kΩ
Gain Pins Open:
G = 10
External Resistor R
G
:
10 < G < 50
Gain Pins Connected:
G = 50
5kΩ
200kΩ22.2kΩ
4
3
2
5
718
V–
0.1µF
Single Supply
Also drawn in simplified form:
Dual Supply
INA156
INA156
6
1
3
8
2
V
OUT
6
7
4
5
Ref
0.1µF
V+
V+
V–
DESIRED GAIN R
G
(V/V) (Ω)
10 Open
20 30k
30 10k
40 3.3k
50 Short
G = 10 + 400kΩ
10kΩ + R
G
V
IN
–
V
IN
+
A1
A2
V
IN
+
V
IN
–
V
OUT
= (V
IN
– V
IN
) • G + V
REF
+–
Bridge
Sensor
INA156
V
REF(1)
+5V
3
2
4
5
76V
OUT
= 0.01V to 4.99V
(2)
NOTES: (1) V
REF
should be adjusted for the desired output level,
keeping in mind that the value of V
REF
affects the common-mode
input range. See Typical Performance Curves. (2) For best
performance, the common-mode input voltage should be kept away
from the transition range of (V+) – 1.8V to (V+) – 0.8V.
1
8
V
IN
+
V
IN
–
9
®
INA156
SETTING THE GAIN
Gain of 10 is achieved simply by leaving the two gain pins
(1 and 8) open. Gain of 50 is achieved by connecting the
gain pins together directly. In the G = 10 configuration, the
gain error is less than 0.4%. In the G = 50 configuration, the
gain error is less than 0.8%.
Gain can be set to any value between 10 and 50 by connect-
ing a resistor RG between the gain pins according to the
following equation:
10 + 400kΩ/(10kΩ + RG) (1)
This is demonstrated in Figure 1 and is shown with the com-
monly used gains and resistor RG values. However, because the
absolute value of internal resistors is not guaranteed, using the
INA156 in this configuration will increase the gain error and
gain drift with temperature, as shown in Figure 3.
FIGURE 3. Typical Gain Error and Gain Error Drift with
External Resistor.
OFFSET TRIMMING
Offset voltage can be adjusted by applying a correction
voltage to the reference terminal. Figure 4 shows an optional
circuit for trimming the output offset voltage. The voltage
applied to the Ref terminal is added to the output signal. An
op amp buffer is used to provide low impedance at the Ref
terminal to preserve good common-mode rejection.
INPUT BIAS CURRENT RETURN
The input impedance of the INA156 is extremely high—
approximately 1013Ω, making it ideal for use with high-imped-
ance sources. However, a path must be provided for the input
bias current of both inputs. This input bias current is less than
10pA and is virtually independent of the input voltage.
Input circuitry must provide a path for this input bias current
for proper operation. Figure 5 shows various provisions for
an input bias current path. Without a bias current path, the
inputs will float to a potential that exceeds the common-
mode range and the input amplifier will saturate.
If the differential source resistance is low, the bias current
return path can be connected to one input (see the thermo-
couple in Figure 5). With higher source impedance, using
two equal resistors provides a balanced input with advan-
tages of lower input offset voltage due to bias current and
better high-frequency common-mode rejection.
FIGURE 4. Optional Trimming of Output Offset Voltage. FIGURE 5. Providing an Input Common-Mode Current Path.
Gain (V/V)
Gain Error (%)
10 15 20 3025
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
Gain Drift (ppm/°C)
400
360
320
280
250
200
160
120
80
40
0
35 40 5045
Gain Drift
Gain Error
OPA336
INA156
Ref
(1)
3
6
25
V
O
Adjustable
Voltage
V
IN
+
(2)
V
IN
–
(2)
NOTES: (1) V
REF
should be adjusted for the desired output
level. The value of V
REF
affects the common-mode input
range. (2) For best performance, common-mode input voltage
should be less than (V+) – 1.8V or greater than (V+)
– 0.8V.
1
8
INA156
3
6
6
6
6
2
47kΩ5
V
REF
47kΩ
Microphone,
Hydrophone, etc.
INA156
3
2
3
2
5
V
REF
Center-tap
provides bias
current return
Low-resistance
thermocouple
provides bias
current return.
Bridge resistance
provides bias
current return
INA156
3
2
10kΩ5
V
REF
Thermocouple
INA156
5
V
REF
Bridge
Sensor
1
8
1
8
1
8
1
8
10
®
INA156
FIGURE 6. Input Offset Voltage Changes with Common-
Mode Voltage.
FIGURE 7. Single-Supply, High-Side Current Monitor.
FIGURE 8. Input Current Protection for Voltages Exceed-
ing the Supply Voltage.
FIGURE 9. Driving Capacitive-Input A/D Converter.
INPUT COMMON-MODE RANGE
The input common-mode range of the INA156 for various
operating conditions is shown in the Typical Performance
Curves. The common-mode input range is limited by the
output voltage swing of A1, an internal circuit node. For the
G = 10 configuration, output voltage of A1 can be expressed as
:
VOUTA1 = – 1/9VREF + (1 + 1/9) VIN– (2)
The input common-mode voltage range can be calculated
using this equation, given that the output of A1 can swing to
within 20mV of either rail. When the input common-mode
range is exceeded (A1’s output is saturated), A2 can still be in
linear operation and respond to changes in the non-inverting
input voltage. However, the output voltage will be invalid.
The common-mode range for the G = 50 configuration is
included in the typical performance curve, “Input Common-
Mode Range vs Output Voltage.”
INPUT RANGE FOR BEST ACCURACY
The internal amplifiers have rail-to-rail input stages, achieved
by using complementary n-channel and p-channel input
pairs. The common-mode input voltage determines whether
the p-channel or the n-channel input stage is operating. The
transition between the input stages is gradual and occurs
between (V+) – 1.8V to (V+) – 1V. Due to these character-
istics, operating the INA156 with input voltages within the
transition region of (V+) – 1.8V to (V+) – 0.8V results in a
shift in input offset voltage, and reduced common-mode and
power supply rejection performance. Typical patterns of the
offset voltage change throughout the input common-mode
range are illustrated in Figure 6. The INA156 can be
operated below or above the transition region with excellent
results. Figure 7 demonstrates the use of the INA156 in a
single-supply, high-side current monitor. In this application,
the INA156 is operated above the transition region.
RAIL-TO-RAIL OUTPUT
A class AB output stage with common-source transistors is
used to achieve rail-to-rail output. For resistive loads
greater than 10kΩ, the output voltage can swing to within
a few millivolts of the supply rail while maintaining low
gain error. For heavier loads and over temperature, see the
typical performance curve “Output Voltage Swing vs Out-
put Current.” The INA156’s low output impedance at high
frequencies makes it suitable for directly driving Capaci-
tive Digital-to-Analog (CDAC) input A/D converters, as
shown in Figure 9.
INPUT PROTECTION
Device inputs are protected by ESD diodes that will conduct
if the input voltages exceed the power supplies by more than
500mV. Momentary voltages greater than 500mV beyond
the power supply can be tolerated if the current on the input
pins is limited to 10mA. This is easily accomplished with
input resistors RLIM, as shown in Figure 8. Many input
signals are inherently current-limited to less than 10mA.
Therefore, a limiting resistor is not required.
INA156
76
4
5
Ref
I
L
2.5A
G = 10
Pins 1 and 8 Open
V+ NOTE: Output is referred to V+.
2
3
1
8
0.02Ω
Load
50mV
+5V
INA156 ADS7818
or
ADS7834
12-Bits
f
SAMPLE
= 500kHz
6
7
4
5
3
2
NOTE: G = 10 configuration
1
8
INA156
5
V
OUT
V
REF
R
LIM
R
LIM
I
OVERLOAD
10mA max
3
6
2
1
8
Input Common-Mode Voltage (V)
Input Offset Voltage (mV)
0.0 0.5 1.0 2.5 3.01.5 2.0
5
4
3
2
1
0
–1
–2
–3
–4
–5 3.5 4.0 4.5 5.55.0
V
S
= 5.5V
P-Channel Operation
Transistion
Region N-Channel
Operation
PACKAGE OPTION ADDENDUM
www.ti.com 16-Aug-2012
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
INA156EA/250 ACTIVE VSSOP DGK 8 250 Green (RoHS
& no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR
INA156EA/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS
& no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR
INA156EA/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR
INA156EA/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
INA156EA/250 VSSOP DGK 8 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
INA156EA/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 16-Aug-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
INA156EA/250 VSSOP DGK 8 250 210.0 185.0 35.0
INA156EA/2K5 VSSOP DGK 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 16-Aug-2012
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
