H/MS3102A22-22P(73) - Hirose Electric

1

MS type Lower Profile Plug

H/MS Series

NEW

2004.6

■Features

1. 20% Height Reduction

When compared with existing H/MS Series connectors

the overall height of plug assemblies is lower, allowing it

to be used in space constrained applications.

2. Cable Exit in 360° Directions

The cable can exit in any of the 8 fixed direction, in 45°

increments.

3. Simple Assembly

The 2-piece design consisting of the contact/insulator

assembly and the back-shell assembly allows termination

without the use of any specialized tools.

4. Water and Dust Protection

IP 67 rating when fully terminated and mated with

corresponding part.

5. TUV Certification

Provided with a protective circuit function for TUV

certification. The (D) pin is directly connected to the

outside metal case.

■Applications

Factory automation equipment, robotic equipment, servo

motors, and a wide variety of industrial and measuring

instruments.

Plug

(45°)

Can be changed

in 45 degree increments

Connector Height Comparison

Existing MS Connector Lower-profile Plug

22-22 Size

Cable Exit Direction of 360°

Circular connector conforming to MIL-C-5015

PAT.P

50.1mm

54.5mm

70mm

3057-10

18

45.5mm

41mm

56.5mm

3057-10

48.2mm

60.7mm

78.7mm

3057-12

22

53.2mm

63.8mm

45.8mm

3057-12

Existing MS Connector Lower-profile Plug

18-10 Size

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

2

3 m ohms max. 1 m ohms max.

5000 M ohms min.

No flashover or insulation breakdown.

Contact resistance: Contact resistance:

4.5 m ohms max. 1.5 m ohms max.

Insulation resistance: 5000 M ohms min.

Insulation resistance: 50 M ohms min. (Humidity state)

500 M ohms min. (Dry state)

When mated with corresponding connector.

1A DC

500 V DC

2250V AC/one minute.

Frequency: 10 to 500 Hz, single amplitude of 0.75 mm,

acceleration of 98 m/s2for 3 hours in 3 axis.

Acceleration of 490 m/s2, 11ms duration, sine half-wave

waveform, 3 cycles in each of the 3 axis.

500 cycles

Temperature: -55ç ➝Room temperature to +125ç ➝Room

temperature Time: 30 ➝10 to 15 ➝30 ➝10 to 15 (Minutes)

5 cycles.

96 hours at temperature of 71ç and humidity of 95% .

No dust penetration.

No water penetration when submerged for 0.5 hour at the depth of 1 meter.

1. Contact resistance

2.

Insulation resistance

3.

Withstanding voltage

4. Vibration

5. Shock

6. Durability

(insertion/ withdrawal)

7. Temperature cycle

8. Humidity

9. Water/dust

protection

Rating

Voltage rating 250VAC, 250V DC (pollution degree: 3, overvoltage category: 3)

500V AC, 500V DC (pollution degree: 2, overvoltage category: 2)

Current rating 23A Max. (18-10 size)

46A Max. (22-22 size)

Operating temperature range

-25ç to +125ç

Storage temperature range

-25ç to +125ç

■Product Specifications

■Materials

Item Specification

18-10 size 22-22 size Conditions

Body

Insulator

Socket Contacts

Gasket

Bushing

Aluminum alloy

PPS

Copper alloy

Silicone Rubber

Chloroprene rubber

Black chromate

Color: Black

Silver plating

Color: Black

-------------------

UL94V-0

-------------------

Item Material Finish Remarks

■Additional Product Information

1. Product number suffixes

(10) Supplied with a wire hole in the locking ring (to prevent loosening of the ring).

(11) Supplied without the wire hole in the locking ring.

2. Corresponding receptacles.

18-10 Size: Part number H/MS3102A18-10P-D-T1(10)

22-22 Size: Part number H/MS3102A22-22P-D-T(10)

No electrical discontinuity for 10 ms max.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

3

■Plug

A

BC

18-10S

X

3057-10

D

41

31

Ø33.5

45.5

Part Number CL No.

Number of Contacts

H/MS08A18-10S-DT10D(10)

H/MS08A18-10S-DT10D(11)

H/MS08A18-10S-DT10D1(10)

H/MS08A18-10S-DT10D1(11)

120-0476-3-10

4

Weight

89g

Applicable Cable Diameter

Ø12~Ø14.3mm

Ø10~Ø12.5mm

Contact solder pot inner diameter

2.5mm

120-0476-3-11

120-0481-3-10

Part Number CL No.

Number of Contacts

H/MS08A18-10S-DT10C(10)

H/MS08A18-10S-DT10C(11)

120-0480-0-10 4

Weight

77.6g

Applicable Cable Diameter

Ø13~Ø14.3mm

Contact solder pot inner diameter

2.5mm

120-0480-0-11

Part Number CL No.

Number of Contacts

H/MS08A22-22S-DT12D(10)

H/MS08A22-22S-DT12D(11)

H/MS08A22-22S-DT12D1(10)

H/MS08A22-22S-DT12D1(11)

120-0477-6-10

4

Weight

127g

Applicable Cable Diameter

Ø13~Ø15.9mm

Ø10~Ø13.5mm

Contact solder pot inner diameter

4.5mm

120-0477-6-11

120-0482-6-10

120-0482-6-11

Shown one type.

A

BC

18-10S

X

D

41

35.5

Ø30

Ø33.5

X

BC

22-22S

D

A

3057-12

45.8

53.2

36

Ø39.5

H/MS08A18-10S-DT10D(10)

H/MS08A18-10S-DT10C(10)

H/MS08A22-22S-DT12D(10)

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

3057-10

A

B

Bushing

Back-shell

Cable

Contacts

Strain relief clamp

Washer

Solder

Insulator/contact assembly

Pre-solder

Conductor portion

B

BA

4

BAssembly Procedures Outline of assemblyProcess

1

2

a. Pass the strain relief clamp, washer, bushing, and hood over the cable, in this order.

b. Prepare the cable and conductors per the dimensions in Table 1.

c. Bend the exposed conductor to the B dimension as indicated in Table 1.

d. Pre-solder the exposed conductor and solder it as shown to the exposed contact.

Note: Use care not to damage the conductor’s insulation.

a. Place over the contact/insulator assembly (in the following order:Back shell, bushing, washer, strain relief clamp).

b. Tighten the Locking ring and Cable clamp to the torque values per Table 2.

c. Tighten the set screw to a torque value of 0.3-0.4 N-m

HRS recommended tool: PB205/1.27 (CL150-0066-3)or equivalent.

d. Using screwdriver tighten the two strain relief clamp screws until both sides of the moveable part are in contact with the cable clamp.

A B

18-10 Size

Table 1

22-22 Size

24mm 13mm

33mm 15mm

The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.

5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN

PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933

http://www.hirose.com

®

Locking Ring Cable Clamp

Table 2

3 to 3.5N •m 5 to 6N •m

3057-10

4.5 mm min.

Cable

Strain relief clamp

Back-shell

Locking ring

Screw

Clamp

Washer

Bushing

Set screw

(Hexagonal hole opposite side 1.27 mm)