Data Sheet Precision Micropower, Low Dropout Voltage References REF19x Series FEATURES TEST PINS Temperature coefficient: 5 ppm/C maximum High output current: 30 mA Low supply current: 45 A maximum Initial accuracy: 2 mV maximum 1 Sleep mode: 15 A maximum Low dropout voltage Load regulation: 4 ppm/mA Line regulation: 4 ppm/V Short-circuit protection Test Pin 1 and Test Pin 5 are reserved for in-package Zener zap. To achieve the highest level of accuracy at the output, the Zener zapping technique is used to trim the output voltage. Because each unit may require a different amount of adjustment, the resistance value at the test pins varies widely from pin to pin and from part to part. The user should leave Pin 1 and Pin 5 unconnected. TP 1 VS 2 REF19x SERIES 8 NC 7 NC SLEEP 3 APPLICATIONS Portable instruments ADCs and DACs Smart sensors Solar powered applications Loop-current-powered instruments NOTES 1. NC = NO CONNECT. 2. TP PINS ARE FACTORY TEST POINTS, NO USER CONNECTION. Figure 1. 8-Lead SOIC_N and TSSOP Pin Configuration (S Suffix and RU Suffix) TP 1 VS 2 GENERAL DESCRIPTION SLEEP 3 The REF19x series references are specified over the extended industrial temperature range (-40C to +85C) with typical performance specifications over -40C to +125C for applications, such as automotive. REF19x SERIES 8 NC 7 NC NOTES 1. NC = NO CONNECT. 2. TP PINS ARE FACTORY TEST POINTS, NO USER CONNECTION. 00371-002 6 OUTPUT TOP VIEW GND 4 (Not to Scale) 5 TP The REF19x series precision band gap voltage references use a patented temperature drift curvature correction circuit and laser trimming of highly stable, thin-film resistors to achieve a very low temperature coefficient and high initial accuracy. The REF19x series is made up of micropower, low dropout voltage (LDV) devices, providing stable output voltage from supplies as low as 100 mV above the output voltage and consuming less than 45 A of supply current. In sleep mode, which is enabled by applying a low TTL or CMOS level to the SLEEP pin, the output is turned off and supply current is further reduced to less than 15 A. 00371-001 6 OUTPUT TOP VIEW GND 4 (Not to Scale) 5 TP Figure 2. 8-Lead PDIP Pin Configuration (P Suffix) Table 1. Nominal Output Voltage Part Number REF191 REF192 REF193 REF194 REF195 REF196 REF198 Nominal Output Voltage (V) 2.048 2.50 3.00 4.50 5.00 3.30 4.096 All electrical grades are available in an 8-lead SOIC package; the PDIP and TSSOP packages are available only in the lowest electrical grade. 1 Initial accuracy does not include shift due to solder heat effect (see the Applications Information section). Rev. L Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)1996-2011 Analog Devices, Inc. All rights reserved. REF19x Series Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Applications....................................................................................... 1 Electrical Characteristics--REF196 @ -40C TA +125C ....................................................................................................... 13 General Description ......................................................................... 1 Electrical Characteristics--REF198 @ TA = 25C.................. 14 Test Pins ............................................................................................. 1 Electrical Characteristics--REF198 @ -40C TA +85C ....................................................................................................... 14 Revision History ............................................................................... 3 Specifications..................................................................................... 4 Electrical Characteristics--REF191 @ TA = 25C .................... 4 Electrical Characteristics--REF191 @ -40C +85C........... 5 Electrical Characteristics--REF198 @ -40C TA 125C15 Absolute Maximum Ratings ......................................................... 16 Thermal Resistance .................................................................... 16 ESD Caution................................................................................ 16 Electrical Characteristics--REF191 @ -40C TA +125C................................................................... 6 Typical Performance Characteristics ........................................... 17 Electrical Characteristics--REF192 @ TA = 25C .................... 6 Applications Information .............................................................. 20 Electrical Characteristics--REF192 @ -40C TA +85C ......................................................................................................... 7 Output Short-Circuit Behavior ................................................ 20 Electrical Characteristics--REF192 @ -40C TA +125C ......................................................................................................... 7 Output Voltage Bypassing ......................................................... 20 Electrical Characteristics--REF193 @ TA = 25C .................... 8 Basic Voltage Reference Connections ..................................... 20 Electrical Characteristics--REF193 @ -40C TA +85C ......................................................................................................... 8 Membrane Switch-Controlled Power Supply............................. 20 Electrical Characteristics--REF193 @ TA -40C +125C ......................................................................................................... 9 Current-Boosted References with Current Limiting............. 21 Device Power Dissipation Considerations.............................. 20 Sleep Mode Operation............................................................... 20 Solder Hear Effect ...................................................................... 21 Electrical Characteristics--REF194 @ TA = 25C .................... 9 Negative Precision Reference Without Precision Resistors.. 22 Electrical Characteristics--REF194 @ -40C TA +85C ....................................................................................................... 10 Stacking Reference ICs for Arbitrary Outputs ....................... 22 Electrical Characteristics--REF194 @ -40C TA +125C ....................................................................................................... 10 Switched Output 5 V/3.3 V Reference..................................... 23 Electrical Characteristics--REF195 @ TA = 25C .................. 11 Fail-Safe 5 V Reference.............................................................. 24 Electrical Characteristics--REF195 @ -40C TA +85C ....................................................................................................... 11 Low Power, Strain Gage Circuit ............................................... 25 Electrical Characteristics--REF195 @ -40C TA +125C ....................................................................................................... 12 Precision Current Source .......................................................... 23 Kelvin Connections.................................................................... 24 Outline Dimensions ....................................................................... 26 Ordering Guide .......................................................................... 27 Electrical Characteristics--REF196 @ TA = 25C .................. 12 Electrical Characteristics--REF196 @ -40C TA +85C ....................................................................................................... 13 Rev. L | Page 2 of 28 Data Sheet REF19x Series REVISION HISTORY 9/11--Rev. K to Rev. L Change to Condition Column for Dropout Voltage Parameter, Table 2 ................................................................................................. 4 Change to Condition Column for Dropout Voltage Parameter, Table 3 ................................................................................................. 5 Change to Operating Temperature Range, Table 23...................16 7/10--Rev. J to Rev. K Add Note 1, Features Section........................................................... 1 Changes to Note 1, Table 2 ............................................................... 4 Changes to Note 1, Table 5 ............................................................... 6 Changes to Note 1, Table 8 ............................................................... 8 Changes to Note 1, Table 11 ............................................................. 9 Changes to Note 1, Table 14 ...........................................................11 Changes to Note 1, Table 17 ...........................................................12 Changes to Note 1, Table 20 ...........................................................14 Moved Figure 22 ..............................................................................20 Added Figure 23, Solder Heat Effect Section, and Figure 24; Renumbered Sequentially ..............................................................21 Moved Negative Precision Reference Without Precision Resistors Section ..............................................................................22 Moved Precision Current Source Section ....................................23 Moved Kelvin Connections Section .............................................24 Moved Figure 32 ..............................................................................25 Updated Outline Dimensions ........................................................26 Changes to Ordering Guide ...........................................................27 3/08--Rev. I to Rev. J Changes to General Description ..................................................... 1 Changes to Specifications Section................................................... 4 Deleted Wafer Test Limits Section ................................................14 Changes to Table 23, Thermal Resistance Section, and Table 24 .............................................................................................16 Changes to Figure 6.........................................................................17 Changes to Device Power Dissipation Considerations Section ...................................................................20 Changes to Current-Boosted References with Current Limiting Section ..............................................................................21 Changes to Precision Current Source Section ............................ 22 Changes to Figure 28 ...................................................................... 23 Changes to Figure 30 ...................................................................... 24 Changes to Low Power, Strain Gage Circuit Section.................. 25 Changes to Ordering Guide ........................................................... 27 9/06--Rev. H to Rev. I Updated Format ................................................................. Universal Changes to Table 25 ........................................................................ 16 Changes to Figure 6 ........................................................................ 16 Changes to Figure 10, Figure 12, Figure 14, and Figure 26 ....... 17 Changes to Figure 18 ...................................................................... 18 Changes to Figure 20 ...................................................................... 19 Changes to Figure 23 ...................................................................... 20 Changes to Figure 25 ...................................................................... 21 Updated Outline Dimensions........................................................ 25 Changes to Ordering Guide ........................................................... 26 6/05--Rev. G to Rev. H Updated Format ................................................................. Universal Changes to Caption in Figure 7..................................................... 16 Updated Outline Dimensions........................................................ 25 Changes to Ordering Guide ........................................................... 26 7/04--Rev. F to Rev. G Changes to Ordering Guide ............................................................. 4 3/04--Rev. E to Rev. F Updated Absolute Maximum Rating.............................................. 4 Changes to Ordering Guide ........................................................... 14 Updated Outline Dimensions........................................................ 24 1/03--Rev. D to Rev. E Changes to Figure 3 and Figure 4 ................................................. 15 Changes to Output Short Circuit Behavior ................................. 17 Changes to Figure 20 ...................................................................... 17 Changes to Figure 26 ...................................................................... 19 Updated Outline Dimensions........................................................ 23 1/96--Revision 0: Initial Version Rev. L | Page 3 of 28 REF19x Series Data Sheet SPECIFICATIONS ELECTRICAL CHARACTERISTICS--REF191 @ TA = 25C @ VS = 3.3 V, TA = 25C, unless otherwise noted. Table 2. Parameter INITIAL ACCURACY 1 E Grade F Grade G Grade LINE REGULATION 2 E Grade F and G Grades LOAD REGULATION2 E Grade F and G Grades DROPOUT VOLTAGE Symbol VO LONG-TERM STABILITY 3 NOISE VOLTAGE DVO eN Condition Min Typ Max Unit IOUT = 0 mA 2.046 2.043 2.038 2.048 2.050 2.053 2.058 V V V 3.0 V VS 15 V, IOUT = 0 mA 2 4 4 8 ppm/V ppm/V VS = 5.0 V, 0 mA IOUT 30 mA 4 6 10 15 0.95 1.25 1.55 ppm/mA ppm/mA V V V mV V p-p VO/VIN VO/VLOAD V S - VO VS = 3.0 V, ILOAD = 2 mA VS = 3.3 V, ILOAD = 10 mA VS = 3.6 V, ILOAD = 30 mA 1000 hours @ 125C 0.1 Hz to 10 Hz 1 1.2 20 Initial accuracy does not include shift due to solder heat effect (see the Applications Information section). Line and load regulation specifications include the effect of self-heating. 3 Long-term stability specification is noncumulative. The drift in subsequent 1000-hour periods is significantly lower than in the first 1000-hour period. 2 Rev. L | Page 4 of 28 Data Sheet REF19x Series ELECTRICAL CHARACTERISTICS--REF191 @ -40C +85C @ VS = 3.3 V, -40C TA +85C, unless otherwise noted. Table 3. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade F Grade G Grade 3 LINE REGULATION 4 E Grade F and G Grades LOAD REGULATION4 E Grade F and G Grades DROPOUT VOLTAGE SLEEP PIN Logic High Input Voltage Logic High Input Current Logic Low Input Voltage Logic Low Input Current SUPPLY CURRENT Sleep Mode 1 2 Symbol TCVO/C Condition Min Typ Max Unit IOUT = 0 mA 2 5 10 5 10 25 ppm/C ppm/C ppm/C 3.0 V VS 15 V, IOUT = 0 mA 5 10 10 20 ppm/V ppm/V VS = 5.0 V, 0 mA IOUT 25 mA 5 10 15 20 0.95 1.25 1.55 ppm/mA ppm/mA V V V -8 0.8 -8 45 15 V A V A A A VO/VIN VO/VLOAD V S - VO VS = 3.0 V, ILOAD = 2 mA VS = 3.3 V, ILOAD = 10 mA VS = 3.6 V, ILOAD = 25 mA VH IH VL IL 2.4 No load No load For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. Rev. L | Page 5 of 28 REF19x Series Data Sheet ELECTRICAL CHARACTERISTICS--REF191 @ -40C TA +125C @ VS = 3.3 V, -40C TA +125C, unless otherwise noted. Table 4. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade F Grade G Grade 3 LINE REGULATION 4 E Grade F and G Grades LOAD REGULATION4 E Grade F and G Grades DROPOUT VOLTAGE 1 2 Symbol TCVO/C Condition Min Typ Max Unit IOUT = 0 mA 2 5 10 ppm/C ppm/C ppm/C 3.0 V VS 15 V, IOUT = 0 mA 10 20 ppm/V ppm/V VS = 5.0 V, 0 mA IOUT 20 mA 10 20 ppm/mA ppm/mA V V VO/VIN VO/VLOAD V S - VO VS = 3.3 V, ILOAD = 10 mA VS = 3.6 V, ILOAD = 20 mA 1.25 1.55 For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. ELECTRICAL CHARACTERISTICS--REF192 @ TA = 25C @ VS = 3.3 V, TA = 25C, unless otherwise noted. Table 5. Parameter INITIAL ACCURACY 1 E Grade F Grade G Grade LINE REGULATION 2 E Grade F and G Grades LOAD REGULATION2 E Grade F and G Grades DROPOUT VOLTAGE Symbol VO LONG-TERM STABILITY 3 NOISE VOLTAGE DVO eN 1 2 3 Condition Min Typ Max Unit IOUT = 0 mA 2.498 2.495 2.490 2.500 2.502 2.505 2.510 V V V 3.0 V VS 15 V, IOUT = 0 mA 2 4 4 8 ppm/V ppm/V VS = 5.0 V, 0 mA IOUT 30 mA 4 6 10 15 1.00 1.40 ppm/mA ppm/mA V V mV V p-p VO/VIN VO/VLOAD V S - VO VS = 3.5 V, ILOAD = 10 mA VS = 3.9 V, ILOAD = 30 mA 1000 hours @ 125C 0.1 Hz to 10 Hz 1.2 25 Initial accuracy does not include shift due to solder heat effect (see the Applications Information section). Line and load regulation specifications include the effect of self-heating. Long-term stability specification is noncumulative. The drift in subsequent 1000-hour periods is significantly lower than in the first 1000-hour period. Rev. L | Page 6 of 28 Data Sheet REF19x Series ELECTRICAL CHARACTERISTICS--REF192 @ -40C TA +85C @ VS = 3.3 V, -40C TA +85C, unless otherwise noted. Table 6. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade F Grade G Grade 3 LINE REGULATION 4 E Grade F and G Grades LOAD REGULATION4 E Grade F and G Grades DROPOUT VOLTAGE SLEEP PIN Logic High Input Voltage Logic High Input Current Logic Low Input Voltage Logic Low Input Current SUPPLY CURRENT Sleep Mode 1 2 Symbol TCVO/C Condition Min Typ Max Unit IOUT = 0 mA 2 5 10 5 10 25 ppm/C ppm/C ppm/C 3.0 V VS 15 V, IOUT = 0 mA 5 10 10 20 ppm/V ppm/V VS = 5.0 V, 0 mA IOUT 25 mA 5 10 15 20 1.00 1.50 ppm/mA ppm/mA V V -8 0.8 -8 45 15 V A V A A A Max Unit VO/VIN VO/VLOAD V S - VO VS = 3.5 V, ILOAD = 10 mA VS = 4.0 V, ILOAD = 25 mA VH IH VL IL 2.4 No load No load For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. ELECTRICAL CHARACTERISTICS--REF192 @ -40C TA +125C @ VS = 3.3 V, -40C TA +125C, unless otherwise noted. Table 7. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade F Grade G Grade 3 LINE REGULATION 4 E Grade F and G Grades LOAD REGULATION4 E Grade F and G Grades DROPOUT VOLTAGE 1 2 Symbol TCVO/C Condition Min Typ IOUT = 0 mA 2 5 10 ppm/C ppm/C ppm/C 3.0 V VS 15 V, IOUT = 0 mA 10 20 ppm/V ppm/V VS = 5.0 V, 0 mA IOUT 20 mA 10 20 ppm/mA ppm/mA V V VO/VIN VO/VLOAD V S - VO VS = 3.5 V, ILOAD = 10 mA VS = 4.0 V, ILOAD = 20 mA For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. Rev. L | Page 7 of 28 1.00 1.50 REF19x Series Data Sheet ELECTRICAL CHARACTERISTICS--REF193 @ TA = 25C @ VS = 3.3 V, TA = 25C, unless otherwise noted. Table 8. Parameter INITIAL ACCURACY 1 G Grade LINE REGULATION 2 G Grade LOAD REGULATION2 G Grade DROPOUT VOLTAGE Symbol VO LONG-TERM STABILITY 3 NOISE VOLTAGE DVO eN 1 2 3 Condition Min Typ Max Unit IOUT = 0 mA 2.990 3.0 3.010 V 3.3 V, VS 15 V, IOUT = 0 mA 4 8 ppm/V VS = 5.0 V, 0 mA IOUT 30 mA VS = 3.8 V, ILOAD = 10 mA VS = 4.0 V, ILOAD = 30 mA 1000 hours @ 125C 0.1 Hz to 10 Hz 6 15 0.80 1.00 ppm/mA V V mV V p-p VO/VIN VO/VLOAD V S - VO 1.2 30 Initial accuracy does not include shift due to solder heat effect (see the Applications Information section). Line and load regulation specifications include the effect of self-heating. Long-term stability specification is noncumulative. The drift in subsequent 1000-hour periods is significantly lower than in the first 1000-hour period. ELECTRICAL CHARACTERISTICS--REF193 @ -40C TA +85C @ VS = 3.3 V, TA = -40C TA +85C, unless otherwise noted. Table 9. Parameter TEMPERATURE COEFFICIENT 1, 2 G Grade 3 LINE REGULATION 4 G Grade LOAD REGULATION4 G Grade DROPOUT VOLTAGE SLEEP PIN Logic High Input Voltage Logic High Input Current Logic Low Input Voltage Logic Low Input Current SUPPLY CURRENT Sleep Mode 1 2 Symbol TCVO/C Condition Typ Max Unit IOUT = 0 mA 10 25 ppm/C 3.3 V VS 15 V, IOUT = 0 mA 10 20 ppm/V VS = 5.0 V, 0 mA IOUT 25 mA VS = 3.8 V, ILOAD = 10 mA VS = 4.1 V, ILOAD = 30 mA 10 20 0.80 1.10 ppm/mA V V -8 0.8 -8 45 15 V A V A A A VO/VIN VO/VLOAD V S - VO VH IH VL IL 2.4 No load No load For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 4 Min Guaranteed by characterization. Line and load regulation specifications include the effect of self-heating. Rev. L | Page 8 of 28 Data Sheet REF19x Series ELECTRICAL CHARACTERISTICS--REF193 @ TA -40C +125C @ VS = 3.3 V, -40C TA +125C, unless otherwise noted. Table 10. Parameter TEMPERATURE COEFFICIENT 1, 2 G Grade 3 LINE REGULATION 4 G Grade LOAD REGULATION4 G Grade DROPOUT VOLTAGE 1 2 Symbol TCVO/C Condition Min Typ Max Unit IOUT = 0 mA 10 ppm/C 3.3 V VS 15 V, IOUT = 0 mA 20 ppm/V VS = 5.0 V, 0 mA IOUT 20 mA VS = 3.8 V, ILOAD = 10 mA VS = 4.1 V, ILOAD = 20 mA 10 VO/VIN VO/VLOAD V S - VO 0.80 1.10 ppm/mA V V For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. ELECTRICAL CHARACTERISTICS--REF194 @ TA = 25C @ VS = 5.0 V, TA = 25C, unless otherwise noted. Table 11. Parameter INITIAL ACCURACY 1 E Grade G Grade LINE REGULATION 2 E Grade G Grade LOAD REGULATION2 E Grade G Grade DROPOUT VOLTAGE Symbol VO LONG-TERM STABILITY 3 NOISE VOLTAGE DVO eN 1 2 3 Condition Min Typ Max Unit IOUT = 0 mA 4.498 4.490 4.5 4.502 4.510 V V 4.75 V VS 15 V, IOUT = 0 mA 2 4 4 8 ppm/V ppm/V VS = 5.8 V, 0 mA IOUT 30 mA 2 4 4 8 0.50 1.30 ppm/mA ppm/mA V V mV V p-p VO/VIN VO/VLOAD V S - VO VS = 5.00 V, ILOAD = 10 mA VS = 5.8 V, ILOAD = 30 mA 1000 hours @ 125C 0.1 Hz to 10 Hz 2 45 Initial accuracy does not include shift due to solder heat effect (see the Applications Information section). Line and load regulation specifications include the effect of self-heating. Long-term stability specification is noncumulative. The drift in subsequent 1000-hour periods is significantly lower than in the first 1000-hour period. Rev. L | Page 9 of 28 REF19x Series Data Sheet ELECTRICAL CHARACTERISTICS--REF194 @ -40C TA +85C @ VS = 5.0 V, TA = -40C TA +85C, unless otherwise noted. Table 12. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade G Grade 3 LINE REGULATION 4 E Grade G Grade LOAD REGULATION4 E Grade G Grade DROPOUT VOLTAGE SLEEP PIN Logic High Input Voltage Logic High Input Current Logic Low Input Voltage Logic Low Input Current SUPPLY CURRENT Sleep Mode 1 2 Symbol TCVO/C Condition Min Typ Max Unit IOUT = 0 mA 2 10 5 25 ppm/C ppm/C 4.75 V VS 15 V, IOUT = 0 mA 5 10 10 20 ppm/V ppm/V VS = 5.80 V, 0 mA IOUT 25 mA 5 10 15 20 0.5 1.30 ppm/mA ppm/mA V V -8 0.8 -8 45 15 V A V A A A Max Unit VO/VIN VO/VLOAD V S - VO VS = 5.00 V, ILOAD = 10 mA VS = 5.80 V, ILOAD = 25 mA VH IH VL IL 2.4 No load No load For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. ELECTRICAL CHARACTERISTICS--REF194 @ -40C TA +125C @ VS = 5.0 V, -40C TA +125C, unless otherwise noted. Table 13. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade G Grade 3 LINE REGULATION 4 E Grade G Grade LOAD REGULATION E Grade Grade DROPOUT VOLTAGE 1 2 Symbol TCVO/C Condition Min Typ IOUT = 0 mA 2 10 ppm/C ppm/C 4.75 V VS 15 V, IOUT = 0 mA 5 10 ppm/V ppm/V VS = 5.80 V, 0 mA IOUT 20 mA 5 10 ppm/mA ppm/mA V V VO/VIN VO/VLOAD V S - VO VS = 5.10 V, ILOAD = 10 mA VS = 5.95 V, ILOAD = 20 mA For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. Rev. L | Page 10 of 28 0.60 1.45 Data Sheet REF19x Series ELECTRICAL CHARACTERISTICS--REF195 @ TA = 25C @ VS = 5.10 V, TA = 25C, unless otherwise noted. Table 14. Parameter INITIAL ACCURACY 1 E Grade F Grade G Grade LINE REGULATION 2 E Grade F and G Grades LOAD REGULATION2 E Grade F and G Grades DROPOUT VOLTAGE Symbol VO LONG-TERM STABILITY 3 NOISE VOLTAGE DVO eN Condition Min Typ Max Unit IOUT = 0 mA 4.998 4.995 4.990 5.0 5.002 5.005 5.010 V V V 5.10 V VS 15 V, IOUT = 0 mA 2 4 4 8 ppm/V ppm/V VS = 6.30 V, 0 mA IOUT 30 mA 2 4 4 8 0.50 1.30 ppm/mA ppm/mA V V mV V p-p VO/VIN VO/VLOAD V S - VO VS = 5.50 V, ILOAD = 10 mA VS = 6.30 V, ILOAD = 30 mA 1000 hours @ 125C 0.1 Hz to 10 Hz 1.2 50 1 Initial accuracy does not include shift due to solder heat effect (see the Applications Information section). Line and load regulation specifications include the effect of self-heating. 3 Long-term stability specification is noncumulative. The drift in subsequent 1000-hour periods is significantly lower than in the first 1000-hour period. 2 ELECTRICAL CHARACTERISTICS--REF195 @ -40C TA +85C @ VS = 5.15 V, TA = -40C TA +85C, unless otherwise noted. Table 15. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade F Grade G Grade 3 LINE REGULATION 4 E Grade F and G Grades LOAD REGULATION4 E Grade F and G Grades DROPOUT VOLTAGE SLEEP PIN Logic High Input Voltage Logic High Input Current Logic Low Input Voltage Logic Low Input Current SUPPLY CURRENT Sleep Mode 1 2 Symbol TCVO/C Condition Min Typ Max Unit IOUT = 0 mA 2 5 10 5 10 25 ppm/C ppm/C ppm/C 5.15 V VS 15 V, IOUT = 0 mA 5 10 10 20 ppm/V ppm/V VS = 6.30 V, 0 mA IOUT 25 mA 5 10 10 20 0.50 1.30 ppm/mA ppm/mA V V -8 0.8 -8 45 15 V A V A A A VO/VIN VO/VLOAD V S - VO VS = 5.50 V, ILOAD = 10 mA VS = 6.30 V, ILOAD = 25 mA VH IH VL IL 2.4 No load No load For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. Rev. L | Page 11 of 28 REF19x Series Data Sheet ELECTRICAL CHARACTERISTICS--REF195 @ -40C TA +125C @ VS = 5.20 V, -40C TA +125C, unless otherwise noted. Table 16. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade F Grade G Grade 3 LINE REGULATION 4 E Grade F and G Grades LOAD REGULATION4 E Grade F and G Grades DROPOUT VOLTAGE 1 2 Symbol TCVO/C Condition Min Typ Max Unit IOUT = 0 mA 2 5 10 ppm/C ppm/C ppm/C 5.20 V VS 15 V, IOUT = 0 mA 5 10 ppm/V ppm/V VS = 6.45 V, 0 mA IOUT 20 mA 5 10 0.60 ppm/mA ppm/mA V 1.45 V VO/VIN VO/VLOAD VS - V O VS = 5.60 V, ILOAD = 10 mA VS = 6.45 V, ILOAD = 20 mA For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. ELECTRICAL CHARACTERISTICS--REF196 @ TA = 25C @ VS = 3.5 V, TA = 25C, unless otherwise noted. Table 17. Parameter INITIAL ACCURACY 1 G Grade LINE REGULATION 2 G Grade LOAD REGULATION2 G Grade DROPOUT VOLTAGE Symbol VO LONG-TERM STABILITY 3 NOISE VOLTAGE DVO eN Condition Min Typ Max Unit IOUT = 0 mA 3.290 3.3 3.310 V 3.50 V VS 15 V, IOUT = 0 mA 4 8 ppm/V VS = 5.0 V, 0 mA IOUT 30 mA VS = 4.1 V, ILOAD = 10 mA VS = 4.3 V, ILOAD = 30 mA 1000 hours @ 125C 0.1 Hz to 10 Hz 6 15 0.80 1.00 ppm/mA V V mV V p-p VO/VIN VO/VLOAD V S - VO 1 1.2 33 Initial accuracy does not include shift due to solder heat effect (see the Applications Information section). Line and load regulation specifications include the effect of self-heating. 3 Long-term stability specification is noncumulative. The drift in subsequent 1000-hour periods is significantly lower than in the first 1000-hour period. 2 Rev. L | Page 12 of 28 Data Sheet REF19x Series ELECTRICAL CHARACTERISTICS--REF196 @ -40C TA +85C @ VS = 3.5 V, TA = -40C TA +85C, unless otherwise noted. Table 18. Parameter TEMPERATURE COEFFICIENT 1, 2 G Grade 3 LINE REGULATION 4 G Grade LOAD REGULATION4 G Grade DROPOUT VOLTAGE SLEEP PIN Logic High Input Voltage Logic High Input Current Logic Low Input Voltage Logic Low Input Current SUPPLY CURRENT Sleep Mode 1 2 Symbol TCVO/C Condition Min Typ Max Unit IOUT = 0 mA 10 25 ppm/C 3.5 V VS 15 V, IOUT = 0 mA 10 20 ppm/V VS = 5.0 V, 0 mA IOUT 25 mA VS = 4.1 V, ILOAD = 10 mA VS = 4.3 V, ILOAD = 25 mA 10 20 0.80 1.00 ppm/mA V V -8 0.8 -8 45 15 V A V A A A Max Unit VO/VIN VO/VLOAD V S - VO VH IH VL IL 2.4 No load No load For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/V0(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. ELECTRICAL CHARACTERISTICS--REF196 @ -40C TA +125C @ VS = 3.50 V, -40C TA +125C, unless otherwise noted. Table 19. Parameter TEMPERATURE COEFFICIENT 1, 2 G Grade 3 LINE REGULATION 4 G Grade LOAD REGULATION4 G Grade DROPOUT VOLTAGE 1 2 Symbol TCVO/C Condition Min Typ IOUT = 0 mA 10 ppm/C 3.50 V VS 15 V, IOUT = 0 mA 20 ppm/V VS = 5.0 V, 0 mA IOUT 20 mA VS = 4.1 V, ILOAD = 10 mA VS = 4.4 V, ILOAD = 20 mA 20 VO/VIN VO/VLOAD V S - VO For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. Rev. L | Page 13 of 28 0.80 1.10 ppm/mA V V REF19x Series Data Sheet ELECTRICAL CHARACTERISTICS--REF198 @ TA = 25C @ VS = 5.0 V, TA = 25C, unless otherwise noted. Table 20. Parameter INITIAL ACCURACY 1 E Grade F Grade G Grade LINE REGULATION 2 E Grade F and G Grades LOAD REGULATION2 E Grade F and G Grades DROPOUT VOLTAGE Symbol VO LONG-TERM STABILITY 3 NOISE VOLTAGE DVO eN Condition Min Typ Max Unit IOUT = 0 mA 4.094 4.091 4.086 4.096 4.098 4.101 4.106 V V V 4.5 V VS 15 V, IOUT = 0 mA 2 4 4 8 ppm/V ppm/V VS = 5.4 V, 0 mA IOUT 30 mA 2 4 4 8 0.502 1.30 ppm/mA ppm/mA V V mV V p-p VO/VIN VO/VLOAD V S - VO VS = 4.6 V, ILOAD = 10 mA VS = 5.4 V, ILOAD = 30 mA 1000 hours @ 125C 0.1 Hz to 10 Hz 1.2 40 1 Initial accuracy does not include shift due to solder heat effect (see the Applications Information section). Line and load regulation specifications include the effect of self-heating. 3 Long-term stability specification is noncumulative. The drift in subsequent 1000-hour periods is significantly lower than in the first 1000-hour period. 2 ELECTRICAL CHARACTERISTICS--REF198 @ -40C TA +85C @ VS = 5.0 V, -40C TA +85C, unless otherwise noted. Table 21. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade F Grade G Grade 3 LINE REGULATION 4 E Grade F and G Grades LOAD REGULATION4 E Grade F and G Grades DROPOUT VOLTAGE SLEEP PIN Logic High Input Voltage Logic High Input Current Logic Low Input Voltage Logic Low Input Current SUPPLY CURRENT Sleep Mode 1 2 Symbol TCVO/C Condition Min Typ Max Unit IOUT = 0 mA 2 5 10 5 10 25 ppm/C ppm/C ppm/C 4.5 V VS 15 V, IOUT = 0 mA 5 10 10 20 ppm/V ppm/V VS = 5.4 V, 0 mA IOUT 25 mA 5 10 10 20 0.502 1.30 ppm/mA ppm/mA V V -8 0.8 -8 45 15 V A V A A A VO/VIN VO/VLOAD V S - VO VS = 4.6 V, ILOAD = 10 mA VS = 5.4 V, ILOAD = 25 mA VH IH VL IL 2.4 No load No load For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Guaranteed by characterization. 4 Line and load regulation specifications include the effect of self-heating. Rev. L | Page 14 of 28 Data Sheet REF19x Series ELECTRICAL CHARACTERISTICS--REF198 @ -40C TA +125C @ VS = 5.0 V, -40C TA +125C, unless otherwise noted. Table 22. Parameter TEMPERATURE COEFFICIENT 1, 2 E Grade F Grade G Grade 3 LINE REGULATION 4 E Grade F and G Grades LOAD REGULATION4 E Grade F and G Grades DROPOUT VOLTAGE 1 2 Symbol TCVO/C Condition 4 Typ Max Unit IOUT = 0 mA 2 5 10 ppm/C ppm/C ppm/C 4.5 V VS 15 V, IOUT = 0 mA 5 10 ppm/V ppm/V VS = 5.6 V, 0 mA IOUT 20 mA 5 10 ppm/mA ppm/mA V V VO/VIN VO/VLOAD V S - VO VS = 4.7 V, ILOAD = 10 mA VS = 5.6 V, ILOAD = 20 mA For proper operation, a 1 F capacitor is required between the output pin and the GND pin of the device. TCVO is defined as the ratio of output change with temperature variation to the specified temperature range expressed in ppm/C. TCVO = (VMAX - VMIN)/VO(TMAX - TMIN) 3 Min Guaranteed by characterization. Line and load regulation specifications include the effect of self-heating. Rev. L | Page 15 of 28 0.60 1.50 REF19x Series Data Sheet ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 23. Parameter Supply Voltage Output to GND Output to GND Short-Circuit Duration Storage Temperature Range PDIP, SOIC Package Operating Temperature Range REF19x Junction Temperature Range PDIP, SOIC Package Lead Temperature (Soldering 60 sec) Rating -0.3 V to +18 V -0.3 V to VS + 0.3 V Indefinite JA is specified for worst-case conditions; that is, JA is specified for the device in socket for PDIP and is specified for the device soldered in the circuit board for the SOIC and TSSOP packages. -65C to +150C Package Type 8-Lead PDIP (N) 8-Lead SOIC (R) 8-Lead TSSOP (RU) -40C to +125C -65C to +150C 300C Table 24. ESD CAUTION Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. L | Page 16 of 28 JA 103 158 240 JC 43 43 43 Unit C/W C/W C/W Data Sheet REF19x Series TYPICAL PERFORMANCE CHARACTERISTICS 50 5.004 3 TYPICAL PARTS 5.15V < VIN < 15V 5.003 BASED ON 600 45 UNITS, 4 RUNS -40C TA +85C 40 PERCENTAGE OF PARTS 5.001 5.000 4.999 4.998 4.997 35 30 25 20 15 10 5 -25 0 25 50 TEMPERATURE (C) 75 0 -20 00371-003 4.996 -50 100 -15 -10 10 15 20 Figure 6. TCVOUT Distribution Figure 3. REF195 Output Voltage vs. Temperature 32 -5 0 5 TCVOUT (ppm/C) 00371-006 OUTPUT VOLTAGE (V) 5.002 40 5.15V VS 15V 28 35 24 30 SUPPLY CURRENT (A) LOAD REGULATION (ppm/V) NORMAL MODE -40C 20 16 +25C 12 +85C 8 25 20 15 10 4 5 0 0 -50 10 15 ILOAD (mA) 20 25 30 Figure 4. REF195 Load Regulator vs. ILOAD 20 SLEEP PIN CURRENT (A) +25C 12 -40C 8 4 -4 -3 -2 VL -1 6 8 100 -5 +85C 4 75 -6 10 VIN (V) 12 14 16 0 -50 00371-005 LINE REGULATION (ppm/mA) 0 25 50 TEMPERATURE (C) Figure 7. Supply Current vs. Temperature 0mA IOUT 25mA 16 0 -25 00371-007 5 Figure 5. REF195 Line Regulator vs. VIN VH -25 0 25 50 TEMPERATURE (C) 75 Figure 8. SLEEP Pin Current vs. Temperature Rev. L | Page 17 of 28 100 00371-008 0 00371-004 SLEEP MODE REF19x Series Data Sheet 5V 0 OFF 100% RIPPLE REJECTION (dB) -20 ON 90% -40 -60 -80 -100 10% -120 100 1k 10k FREQUENCY (Hz) 100k 20mV 00371-009 1M Figure 9. Ripple Rejection vs. Frequency 100s Figure 12. Load Transient Response 10F 10F 1F 1k REF REF19x 2 6 100% VG = 2V p-p 1F Z 90% VS = 4V 4 1mA LOAD 3 2 10% 1 0% 0 30mA LOAD 2V 10 100 1k 10k 100k FREQUENCY (Hz) 1M 10M 100s 00371-011 ZO () 1F 2V 200V 4 10mA 0 Figure 13. Load Transient Response Measurement Circuit Figure 10. Ripple Rejection vs. Frequency Measurement Circuit VIN = 7V 1F Figure 11. Output Impedance vs. Frequency Figure 14. Power-On Response Time REF19x 2 VIN = 7V 6 4 1F Figure 15. Power-On Response Time Measurement Circuit Rev. L | Page 18 of 28 00371-014 4 10F 6 4 OUTPUT 6 00371-010 2 2 00371-013 REF19x 1k VIN = 15V REF19x VIN = 15V 00371-015 10 00371-012 0% Data Sheet REF19x Series 5V 5V ON 100% 90% 90% IL = 1mA VOUT IL = 10mA 10% 10% 200mV 00371-016 2ms 1V 35 REF19x VOUT 2 6 30 1F Figure 17. SLEEP Response Time Measurement Circuit 25 20 15 10 5 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 REF195 DROPOUT VOLTAGE (V) 0.8 Figure 19. Load Current vs. REF195 Dropout Voltage Rev. L | Page 19 of 28 0.9 00371-019 4 LOAD CURRENT (mA) 3 200s Figure 18. Line Transient Response Figure 16. SLEEP Response Time VIN = 15V 00371-018 0% 0% 00371-017 OFF 100% REF19x Series Data Sheet APPLICATIONS INFORMATION OUTPUT SHORT-CIRCUIT BEHAVIOR SLEEP MODE OPERATION The REF19x family of devices is totally protected from damage due to accidental output shorts to GND or to VS. In the event of an accidental short-circuit condition, the reference device shuts down and limits its supply current to 40 mA. All REF19x devices include a sleep capability that is TTL/CMOSlevel compatible. Internally, a pull-up current source to VS is connected at the SLEEP pin. This permits the SLEEP pin to be driven from an open collector/drain driver. A logic low or a 0 V condition on the SLEEP pin is required to turn off the output stage. During sleep, the output of the references becomes a high impedance state where its potential would then be determined by external circuitry. If the sleep feature is not used, it is recommended that the SLEEP pin be connected to VS (Pin 2). VS OUTPUT BASIC VOLTAGE REFERENCE CONNECTIONS SLEEP (SHUTDOWN) Figure 20. Simplified Schematic REF19x DEVICE POWER DISSIPATION CONSIDERATIONS The REF19x family of references is capable of delivering load currents to 30 mA with an input voltage that ranges from 3.3 V to 15 V. When these devices are used in applications with large input voltages, exercise care to avoid exceeding the maximum internal power dissipation of these devices. Exceeding the published specifications for maximum power dissipation or junction temperature can result in premature device failure. The following formula should be used to calculate the maximum junction temperature or dissipation of the device: TJ - TA JA where TJ and TA are the junction and ambient temperatures, respectively; PD is the device power dissipation; and JA is the device package thermal resistance. OUTPUT VOLTAGE BYPASSING For stable operation, low dropout voltage regulators and references generally require a bypass capacitor connected from their VOUT pins to their GND pins. Although the REF19x family of references is capable of stable operation with capacitive loads exceeding 100 F, a 1 F capacitor is sufficient to guarantee rated performance. The addition of a 0.1 F ceramic capacitor in parallel with the bypass capacitor improves load current transient performance. For best line voltage transient performance, it is recommended that the voltage inputs of these devices be bypassed with a 10 F electrolytic capacitor in parallel with a 0.1 F ceramic capacitor. 0.1F 8 NC 2 7 SLEEP 3 6 NC OUTPUT 4 5 NC + 1F TANT 0.1F NC = NO CONNECT Figure 21. Basic Voltage Reference Connections MEMBRANE SWITCH-CONTROLLED POWER SUPPLY With output load currents in the tens of mA, the REF19x family of references can operate as a low dropout power supply in hand-held instrument applications. In the circuit shown in Figure 22, a membrane on/off switch is used to control the operation of the reference. During an initial power-on condition, the SLEEP pin is held to GND by the 10 k resistor. Recall that this condition (read: three-state) disables the REF19x output. When the membrane on switch is pressed, the SLEEP pin is momentarily pulled to VS, enabling the REF19x output. At this point, current through the 10 k resistor is reduced and the internal current source connected to the SLEEP pin takes control. Pin 3 assumes and remains at the same potential as VS. When the membrane off switch is pressed, the SLEEP pin is momentarily connected to GND, which once again disables the REF19x output. REF19x VS 1k 5% ON NC 1 8 2 7 3 6 4 5 NC NC OUTPUT NC +1F TANT 10k OFF NC = NO CONNECT Figure 22. Membrane Switch Controlled Power Supply Rev. L | Page 20 of 28 00371-022 PD = 10F NC 1 VS 00371-021 00371-020 GND The circuit in Figure 21 illustrates the basic configuration for the REF19x family of references. Note the 10 F/0.1 F bypass network on the input and the 1 F/0.1 F bypass network on the output. It is recommended that no connections be made to Pin 1, Pin 5, Pin 7, and Pin 8. If the sleep feature is not required, Pin 3 should be connected to VS. Data Sheet REF19x Series SUPPLIER TP TC USER TP TC TC TC = -5C SUPPLIER tP USER tP TP TC = -5C tP MAXIMUM RAMP UP RATE = 3C/s TEMPERATURE MAXIMUM RAMP DOWN RATE = 6C/s TL TSMAX tL PREHEAT AREA TSMIN tS 00371-123 25 TIME 25C TO PEAK TIME Figure 23. Classification Profile (Not to Scale) The mechanical stress and heat effect of soldering a part to a PCB can cause output voltage of a reference to shift in value. The output voltage of REF195 shifts after the part undergoes the extreme heat of a lead-free soldering profile, like the one shown in Figure 23. The materials that make up a semiconductor device and its package have different rates of expansion and contraction. The stress on the dice has changed position, causing shift on the output voltage, after exposed to extreme soldering temperatures. This shift is similar but more severe than thermal hysteresis. CURRENT-BOOSTED REFERENCES WITH CURRENT LIMITING Whereas the 30 mA rated output current of the REF19x series is higher than is typical of other reference ICs, it can be boosted to higher levels, if desired, with the addition of a simple external PNP transistor, as shown in Figure 25. Full-time current limiting is used to protect the pass transistor against shorts. +VS = 6V TO 9V (SEE TEXT) Typical result of soldering temperature effect on REF19x output value shift is shown in Figure 24. It shows the output shift due to soldering and does not include mechanical stress. C2 100F 25V R2 1.5k C3 0.1F U1 3 1N4148 (SEE TEXT ON SLEEP) 5 4 VS COMMON REF196 6 VOUT (V) REF192 REF193 REF196 REF194 REF195 2.5 3.0 3.3 4.5 5.0 F +VOUT 3.3V @ 150mA S (SEE TABLE) 4 U1 C1 10F/25V R3 1.82k (TANTALUM) S F + R1 VOUT COMMON Figure 25. Boosted 3.3 V Referenced with Current Limiting 2 SHIFT DUE TO SOLDER HEAT EFFECT (%) Figure 24. Output Shift due to Solder Heat Effect 0.16 00371-124 0.14 0.12 0.10 0.08 0.06 0.04 0 0.02 -0.02 -0.04 -0.06 -0.08 -0.10 -0.12 0 -0.14 1 -0.16 NUMBER OF UNITS Q2 2N3906 + D1 VC OUTPUT TABLE R1 1k 2 6 3 Q1 TIP32A (SEE TEXT) R4 2 00371-023 SOLDER HEAT EFFECT In this circuit, the power supply current of reference U1 flowing through R1 to R2 develops a base drive for Q1, whose collector provides the bulk of the output current. With a typical gain of 100 in Q1 for 100 mA to 200 mA loads, U1 is never required to furnish more than a few mA, so this factor minimizes temperature-related drift. Short-circuit protection is provided by Q2, which clamps the drive to Q1 at about 300 mA of load current, with values as shown in Figure 25. With this separation of control and power functions, dc stability is optimum, allowing most advantageous use of premium grade REF19x devices for U1. Of course, load Rev. L | Page 21 of 28 REF19x Series Data Sheet The requirement for a heat sink on Q1 depends on the maximum input voltage and short-circuit current. With VS = 5 V and a 300 mA current limit, the worst-case dissipation of Q1 is 1.5 W, less than the TO-220 package 2 W limit. However, if smaller TO-39 or TO-5 package devices, such as the 2N4033, are used, the current limit should be reduced to keep maximum dissipation below the package rating. This is accomplished by simply raising R4. A tantalum output capacitor is used at C1 for its low equivalent series resistance (ESR), and the higher value is required for stability. Capacitor C2 provides input bypassing and can be an ordinary electrolytic. Shutdown control of the booster stage is an option, and when used, some cautions are needed. Due to the additional active devices in the VS line to U1, a direct drive to Pin 3 does not work as with an unbuffered REF19x device. To enable shutdown control, the connection from U1 to Q2 is broken at the X, and Diode D1 then allows a CMOS control source, VC, to drive U1 to 3 for on/off operation. Startup from shutdown is not as clean under heavy load as it is in basic REF19x series, and can require several milliseconds under load. Nevertheless, it is still effective and can fully control 150 mA loads. When shutdown control is used, heavy capacitive loads should be minimized. NEGATIVE PRECISION REFERENCE WITHOUT PRECISION RESISTORS In many current-output CMOS DAC applications where the output signal voltage must be the same polarity as the reference voltage, it is often necessary to reconfigure a current-switching DAC into a voltage-switching DAC using a 1.25 V reference, an op amp, and a pair of resistors. Using a current-switching DAC directly requires an additional operational amplifier at the output to reinvert the signal. A negative voltage reference is then desirable because an additional operational amplifier is not required for either reinversion (current-switching mode) or amplification (voltage-switching mode) of the DAC output voltage. In general, any positive voltage reference can be converted into a negative voltage reference using an operational amplifier and a pair of matched resistors in an inverting configuration. The disadvantage to this approach is that the largest single source of error in the circuit is the relative matching of the resistors used. The circuit illustrated in Figure 26 avoids the need for tightly matched resistors by using an active integrator circuit. In this circuit, the output of the voltage reference provides the input drive for the integrator. To maintain circuit equilibrium, the VS 10k 2N3906 SLEEP TTL/CMOS 2 VS 3 SLEEP OUTPUT 6 1F 1k +5V REF19x GND 10k 100 A1 1F 4 -VREF 100k -5V A1 = 1/2 OP295, 1/2 OP291 00371-024 Because of the current limiting configuration, the dropout voltage circuit is raised about 1.1 V over that of the REF19x devices, due to the VBE of Q1 and the drop across Current Sense Resistor R4. However, overall dropout is typically still low enough to allow operation of a 5 V to 3.3 V regulator/reference using the REF196 for U1 as noted, with a VS as low as 4.5 V and a load current of 150 mA. integrator adjusts its output to establish the proper relationship between the VOUT and GND references. Thus, any desired negative output voltage can be selected by substituting for the appropriate reference IC. The sleep feature is maintained in the circuit with the simple addition of a PNP transistor and a 10 k resistor. Figure 26. Negative Precision Voltage Reference Uses No Precision Resistors One caveat to this approach is that although rail-to-rail output amplifiers work best in the application, these operational amplifiers require a finite amount (mV) of headroom when required to provide any load current; consider this issue when choosing the negative supply for the circuit. STACKING REFERENCE ICs FOR ARBITRARY OUTPUTS Some applications may require two reference voltage sources that are a combined sum of standard outputs. The circuit in Figure 27 shows how this stacked output reference can be implemented. Two reference ICs are used, fed from a common unregulated input, VS. The outputs of the individual ICs are connected in series, as shown in Figure 27, which provide two output voltages, VOUT1 and VOUT2. VOUT1 is the terminal voltage of U1, whereas VOUT2 is the sum of this voltage and the terminal voltage of U2. U1 and U2 are chosen for the two voltages that supply the required outputs (see Table 1). If, for example, both U1 and U2 are REF192s, the two outputs are 2.5 V and 5.0 V. OUTPUT TABLE U1/U2 +VS VS > VOUT2 + 0.15V VOUT1 (V) VOUT2 (V) REF192/REF192 2.5 REF192/REF194 2.5 REF192/REF195 2.5 5.0 7.0 7.5 2 C1 0.1F U2 3 REF19x +VOUT2 6 (SEE TABLE) VO (U2) 4 + C2 1F 2 C3 0.1F U1 3 REF19x 4 VIN COMMON Rev. L | Page 22 of 28 6 (SEE TABLE) VO (U1) + C4 1F R1 3.9k +VOUT1 (SEE TEXT) VOUT COMMON Figure 27. Stacking Voltage References with the REF19x 00371-025 management should still be exercised. A short, heavy, low dc resistance (DCR) conductor should be used from U1 to 6 to the VOUT Sense Point S, where the collector of Q1 connects to the load, Point F. Data Sheet REF19x Series +VS VS > VOUT2 + 0.15V 2 U1 REF192 4 VIN COMMON D1 AD589 6 VO (U1) VO (D1) + C2 1F + C3 1F R1 4.99k +VOUT2 3.735V (SEE TEXT) +VOUT1 1.235V VOUT COMMON Figure 28. Stacking Voltage References with the REF192 PRECISION CURRENT SOURCE 2 VS REF19x 3 SLEEP OUTPUT 6 GND 4 1F R1 ISY ADJUST P1 IOUT VIN IOUT x RL (MAX) + VSY (MIN) IOUT = VOUT RSET VOUT RSET RSET RL + ISY (REF19x) FOR EXAMPLE, REF195: VOUT = 5V IOUT = 5mA R1 = 953 P1 = 100, 10-TURN >> ISY Figure 29. A Low Dropout, Precision Current Source SWITCHED OUTPUT 5 V/3.3 V REFERENCE Applications often require digital control of reference voltages, selecting between one stable voltage and a second. With the sleep feature inherent to the REF19x series, switched output reference configurations are easily implemented with little additional hardware. The circuit in Figure 30 shows the general technique, which takes advantage of the output wire-OR capability of the REF19x device family. When off, a REF19x device is effectively an open circuit at the output node with respect to the power supply. When on, a REF19x device can source current up to its current rating, but sink only a few A (essentially, just the relatively low current of the internal output scaling divider). Consequently, when two devices are wired together at their common outputs, the output voltage is the same as the output voltage for the on device. The off state device draws a small standby current of 15 A (maximum), but otherwise does not interfere with operation of the on device, which can operate to its full current rating. Note that the two devices in the circuit conveniently share both input and output capacitors, and with CMOS logic drive, it is power efficient. OUTPUT TABLE In low power applications, the need often arises for a precision current source that can operate on low supply voltages. As shown in Figure 29, any one of the devices in the REF19x family of references can be configured as a precision current source. The circuit configuration illustrated is a floating current source with a grounded load. The output voltage of the reference is bootstrapped across RSET, which sets the output current into the load. With this configuration, circuit precision is maintained for load currents in the range from the reference's supply current (typically 30 A) to approximately 30 mA. The low dropout voltage of these devices maximizes the current source's output voltage compliance without excess headroom. U1/U2 VC* VOUT (V) REF195/ HIGH 5.0 REF196 LOW 3.3 REF194/ HIGH 4.5 REF195 LOW 5.0 +VS = 6V 2 VC 1 2 3 4 *CMOS LOGIC LEVELS U1 3 REF19x 6 (SEE TABLE) U3A U3B 74HC04 74HC04 4 +VOUT 2 U2 3 REF19x 6 + C2 1F (SEE TABLE) C1 0.1F 4 VIN COMMON VOUT COMMON Figure 30. Switched Output Reference Rev. L | Page 23 of 28 00371-028 3 00371-026 C1 0.1F VS 00371-027 Although this concept is simple, some cautions are needed. Because the lower reference circuit must sink a small bias current from U2 (50 A to 100 A), plus the base current from the series PNP output transistor in U2, either the external load of U1 or R1 must provide a path for this current. If the U1 minimum load is not well defined, Resistor R1 should be used, set to a value that conservatively passes 600 A of current with the applicable VOUT1 across it. Note that the two U1 and U2 reference circuits are locally treated as macrocells, each having its own bypasses at input and output for best stability. Both U1 and U2 in this circuit can source dc currents up to their full rating. The minimum input voltage, VS, is determined by the sum of the outputs, VOUT2, plus the dropout voltage of U2. A related variation on stacking two 3-terminal references is shown in Figure 28, where U1, a REF192, is stacked with a 2-terminal reference diode, such as the AD589. Like the 3-terminal stacked reference shown in Figure 27, this circuit provides two outputs, VOUT1 and VOUT2, which are the individual terminal voltages of D1 and U1, respectively. Here this is 1.235 V and 2.5 V, which provides a VOUT2 of 3.735 V. When using 2-terminal reference diodes, such as D1, the rated minimum and maximum device currents must be observed, and the maximum load current from VOUT1 can be no greater than the current setup by R1 and VO (U1). When VO (U1) is equal to 2.5 V, R1 provides a 500 A bias to D1, so the maximum load current available at VOUT1 is 450 A or less. REF19x Series Data Sheet Due to the nature of the wire-OR, one application caveat should be understood about this circuit. Because U1 and U2 can only source current effectively, negative going output voltage changes, which require the sinking of current, necessarily take longer than positive going changes. In practice, this means that the circuit is quite fast when undergoing a transition from 3.3 V to 5 V, but the transition from 5 V to 3.3 V takes longer. Exactly how much longer is a function of the load resistance, RL, seen at the output and the typical 1 F value of C2. In general, a conservative transition time is approximately several milliseconds for load resistances in the range of 100 to 1 k. Note that for highest accuracy at the new output voltage, several time constants should be allowed (for example, >7.6 time constants for <1/2 LSB error @ 10 bits). KELVIN CONNECTIONS In many portable applications where the PCB cost and area go hand-in-hand, circuit interconnects are very often narrow. These narrow lines can cause large voltage drops if the voltage reference is required to provide load currents to various functions. The interconnections of a circuit can exhibit a typical line resistance of 0.45 m/square (for example, 1 oz. Cu). In applications where these devices are configured as low dropout voltage regulators, these wiring voltage drops can become a large source of error. To circumvent this problem, force and sense connections can be made to the reference through the use of an operational amplifier, as shown in Figure 31. This method provides a means by which the effects of wiring resistance voltage drops can be eliminated. Load currents flowing through wiring resistance produce an I-R error (ILOAD x RWIRE) at the load. However, the Kelvin connection overcomes the problem by including the wiring resistance within the forcing loop of the op amp. Because the op amp senses the load voltage, op amp loop control forces the output to compensate for the wiring error and to produce the correct voltage at the load. Depending on the reference device chosen, operational amplifiers that can be used in this application are the OP295, OP292, and OP183. VS VS RLW 2 VS SLEEP 3 OUTPUT 2 3 6 REF19x GND 4 1F A1 1 RLW A1 = 1/2 OP295 1/2 OP292 100k OP183 +VOUT SENSE +VOUT FORCE RL 00371-029 Using dissimilar REF19x series devices with this configuration allows logic selection between the U1/U2-specified terminal voltages. For example, with U1 (a REF195) and U2 (a REF196), as noted in the table in Figure 30, changing the CMOS-compatible VC logic control voltage from high to low selects between a nominal output of 5.0 V and 3.3 V, and vice versa. Other REF19x family units can also be used for U1/U2, with similar operation in a logic sense, but with outputs as per the individual paired devices (see the table in Figure 30). Of course, the exact output voltage tolerance, drift, and overall quality of the reference voltage is consistent with the grade of individual U1 and U2 devices. Figure 31. Low Dropout, Kelvin-Connected Voltage Reference FAIL-SAFE 5 V REFERENCE Some critical applications require a reference voltage to be maintained at a constant voltage, even with a loss of primary power. The low standby power of the REF19x series and the switched output capability allow a fail-safe reference configuration to be implemented rather easily. This reference maintains a tight output voltage tolerance for either a primary power source (ac line derived) or a standby (battery derived) power source, automatically switching between the two as the power conditions change. The circuit in Figure 32 illustrates this concept, which borrows from the switched output idea of Figure 30, again using the REF19x device family output wire-OR capability. In this case, because a constant 5 V reference voltage is desired for all conditions, two REF195 devices are used for U1 and U2, with their on/off switching controlled by the presence or absence of the primary dc supply source, VS. VBAT is a 6 V battery backup source that supplies power to the load only when VS fails. For normal (VS present) power conditions, VBAT sees only the 15 A (maximum) standby current drain of U1 in its off state. In operation, it is assumed that for all conditions, either U1 or U2 is on, and a 5 V reference output is available. With this voltage constant, a scaled down version is applied to the Comparator IC U3, providing a fixed 0.5 V input to the negative input for all power conditions. The R1 to R2 divider provides a signal to the U3 positive input proportionally to VS, which switches U3 and U1/U2, dependent upon the absolute level of VS. In Figure 32, Op Amp U3 is configured as a comparator with hysteresis, which provides clean, noise-free output switching. This hysteresis is important to eliminate rapid switching at the threshold due to VS ripple. Furthermore, the device chosen is the AD820, a rail-to-rail output device. This device provides high and low output states within a few mV of VS, ground for accurate thresholds, and compatible drive for U2 for all VS conditions. R3 provides positive feedback for circuit hysteresis, changing the threshold at the positive input as a function of the output of U3. Rev. L | Page 24 of 28 Data Sheet REF19x Series +VBAT +VS R1 1.1M R3 10M R6 100 3 + 7 2 - 4 C2 0.1F 2 U1 3 REF195 6 (SEE TABLE) Q1 2N3904 C1 0.1F 5.000V 4 6 + C3 1F U2 REF195 6 (SEE TABLE) R4 900k 4 R5 100k VOUT COMMON 00371-030 C4 0.1F 2 AD820 3 R2 100k VS, VBAT COMMON U3 Figure 32. Fail-Safe 5 V Reference For VS levels lower than the lower threshold, the output of U3 is low, thus U2 and Q1 are off and U1 is on. For VS levels higher than the upper threshold, the situation reverses, with U1 off and both U2 and Q1 on. In the interest of battery power conservation, all of the comparison switching circuitry is powered from VS and is arranged so that when VS fails, the default output comes from U1. 100 REF195 2 10F For the R1 to R3 values, as shown in Figure 32, lower/upper VS switching thresholds are approximately 5.5 V and 6 V, respectively. These can be changed to suit other VS supplies, as can the REF19x devices used for U1 and U2, over a range of 2.5 V to 5 V of output. U3 can operate down to a VS of 3.3 V, which is generally compatible with all REF19x family devices. + 10F 6 + 1F 4 57k 1% 0.1F 4 3 + 0.1F 10k 1% 1/4 OP492 2 - 1 2N2222 11 500 0.1% LOW POWER, STRAIN GAGE CIRCUIT Rev. L | Page 25 of 28 10k 1% 0.01F 20k 1% 13 - 1/4 OP492 14 20k 1% 10k 1% 2.21k 10 + 7 OUTPUT 5 + 9 - 1/4 OP492 6 - 1/4 OP492 12 + 8 20k 1% 20k 1% Figure 33. Low Power, Strain Gage Circuit 00371-031 As shown in Figure 33, the REF19x family of references can be used in conjunction with low supply voltage operational amplifiers, such as the OP492 or the OP747, in a self-contained strain gage circuit in which the REF195 is used as the core. Other references can be easily accommodated by changing circuit element values. The references play a dual role, first as the voltage regulator to provide the supply voltage requirements of the strain gage and the operational amplifiers, and second as a precision voltage reference for the current source used to stimulate the bridge. A distinct feature of the circuit is that it can be remotely controlled on or off by digital means via the SLEEP pin. REF19x Series Data Sheet OUTLINE DIMENSIONS 0.400 (10.16) 0.365 (9.27) 0.355 (9.02) 8 5 1 4 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 0.100 (2.54) BSC 0.060 (1.52) MAX 0.210 (5.33) MAX 0.015 (0.38) MIN 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) SEATING PLANE 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) GAUGE PLANE 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.430 (10.92) MAX 0.005 (0.13) MIN 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) 070606-A COMPLIANT TO JEDEC STANDARDS MS-001 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. Figure 34. 8-Lead Plastic Dual In-Line Package [PDIP] P-Suffix (N-8) Dimensions shown in inches and (millimeters) 5.00 (0.1968) 4.80 (0.1890) 3.10 3.00 2.90 8 4.00 (0.1574) 3.80 (0.1497) 5 4.50 4.40 4.30 1 0.25 (0.0098) 0.10 (0.0040) 0.65 BSC 1.20 MAX 0.30 0.19 4 1.27 (0.0500) BSC PIN 1 COPLANARITY 0.10 5 6.20 (0.2441) 5.80 (0.2284) 6.40 BSC 4 0.15 0.05 8 1 SEATING 0.20 PLANE 0.09 COPLANARITY 0.10 SEATING PLANE 8 0 0.75 0.60 0.45 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) 0.31 (0.0122) 0.50 (0.0196) 0.25 (0.0099) 8 0 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. COMPLIANT TO JEDEC STANDARDS MO-153-AA Figure 35. 8-Lead Thin Shrink Small Outline Package [TSSOP] (RU-8) Dimensions shown in millimeters Figure 36. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body S-Suffix (R-8) Dimensions shown in millimeters and (inches) Rev. L | Page 26 of 28 45 Data Sheet REF19x Series ORDERING GUIDE Model 1 REF191ES REF191ES-REEL REF191ESZ REF191ESZ-REEL REF191GS REF191GS-REEL REF191GSZ REF191GSZ-REEL REF192ES REF192ES-REEL REF192ES-REEL7 REF192ESZ REF192ESZ-REEL REF192ESZ-REEL7 REF192FS REF192FS-REEL REF192FS-REEL7 REF192FSZ REF192FSZ-REEL REF192FSZ-REEL7 REF192GPZ REF192GRUZ REF192GRUZ-REEL7 REF192GS REF192GS-REEL REF192GS-REEL7 REF192GSZ REF192GSZ-REEL REF192GSZ-REEL7 REF193GSZ REF193GSZ-REEL REF194ES REF194ESZ REF194ESZ-REEL REF194GS-REEL REF194GS-REEL7 REF194GSZ REF194GSZ-REEL REF194GSZ-REEL7 REF195ES REF195ES-REEL REF195ESZ REF195ESZ-REEL REF195FS REF195FS-REEL REF195FSZ REF195FSZ-REEL REF195GPZ REF195GRU-REEL7 REF195GRUZ REF195GRUZ-REEL7 Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Description 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead PDIP 8-Lead TSSOP 8-Lead TSSOP 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead PDIP 8-Lead TSSOP 8-Lead TSSOP 8-Lead TSSOP Rev. L | Page 27 of 28 Package Option S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) P-Suffix (N-8) RU-8 RU-8 S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) P-Suffix (N-8) RU-8 RU-8 RU-8 Ordering Quantity 2,500 2,500 2,500 2,500 2,500 1,000 2,500 1,000 2,500 1,000 2,500 1,000 1,000 2,500 1,000 2,500 1,000 2,500 2,500 2,500 1,000 2,500 1,000 2,500 2,500 2,500 2,500 1,000 1,000 REF19x Series Model 1 REF195GS REF195GS-REEL REF195GS-REEL7 REF195GSZ REF195GSZ-REEL REF195GSZ-REEL7 REF196GRUZ-REEL7 REF196GSZ REF196GSZ-REEL REF196GSZ-REEL7 REF198ES REF198ES-REEL REF198ESZ REF198ESZ-REEL REF198ESZ-REEL7 REF198FS-REEL REF198FSZ REF198FSZ-REEL REF198GRUZ REF198GRUZ-REEL7 REF198GS REF198GS-REEL REF198GSZ REF198GSZ-REEL 1 Data Sheet Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Description 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead TSSOP 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead TSSOP 8-Lead TSSOP 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N Z = RoHS Compliant Part. (c)1996-2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D00371-0-9/11(L) Rev. L | Page 28 of 28 Package Option S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) RU-8 S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) RU-8 RU-8 S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) S-Suffix (R-8) Ordering Quantity 2,500 1,000 2,500 1,000 1,000 2,500 1,000 2,500 2,500 1,000 2,500 2,500 2,500 2,500 2,500