LMP2232 LMP2232 Dual Micropower, 1.6V, Precision, Operational Amplifier with CMOS Input Literature Number: SNOSB02B LMP2232 Dual Micropower, 1.6V, Precision, Operational Amplifier with CMOS Input General Description Features The LMP2232 is a dual micropower precision amplifier designed for battery powered applications. The 1.6V to 5.5V operating supply voltage range and quiescent power consumption of only 26 W extend the battery life in portable systems. The LMP2232 is part of the LMP(R) precision amplifier family. The high impedance CMOS input makes it ideal for instrumentation and other sensor interface applications. The LMP2232 has a maximum offset voltage of 150 V and maximum offset voltage drift of only 0.5 V/C along with low bias current of only 20 fA. These precise specifications make the LMP2232 a great choice for maintaining system accuracy and long term stability. The LMP2232 has a rail-to-rail output that swings 15 mV from the supply voltage, which increases system dynamic range. The common mode input voltage range extends 200 mV below the negative supply, thus the LMP2232 is ideal for ground sensing in single supply applications. The LMP2232 is offered in 8-pin SOIC and MSOP packages. The LMP2231 is the single version of this product and the LMP2234 is the quad version of this product. Both of these products are available on National Semiconductor's website. (For VS = 5V, Typical unless otherwise noted) 16 A Supply current at 1.8V 1.6V to 5.5V Operating voltage range 0.5 V/C (max) Low TCVOS 150 V (max) VOS 20 fA Input bias current 120 dB PSRR 97 dB CMRR 120 dB Open loop gain 130 kHz Gain bandwidth product 58 V/ms Slew rate 60 nV/Hz Input voltage noise, f = 1 kHz -40C to 125C Temperature range Applications Precision instrumentation amplifiers Battery powered medical instrumentation High impedance sensors Strain gauge bridge amplifier Thermocouple amplifiers Typical Application 30033974 Strain Gauge Bridge Amplifier LMP(R) is a registered trademark of National Semiconductor Corporation. (c) 2008 National Semiconductor Corporation 300339 www.national.com LMP2232 Dual, Micropower, 1.6V, Precision, Operational Amplifier with CMOS Input December 18, 2008 LMP2232 Mounting Temperature Infrared or Convection (20 sec.) Wave Soldering Lead Temperature (10 sec.) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Human Body Model Machine Model Differential Input Voltage Supply Voltage (VS = V+ - V-) Voltage on Input/Output Pins Storage Temperature Range Junction Temperature (Note 3) Operating Ratings 2000V 100V 300 mV 6V V+ + 0.3V, V- - 0.3V -65C to 150C 150C +235C +260C (Note 1) Operating Temperature Range (Note 3) Supply Voltage (VS = V+ - V-) -40C to 125C 1.6V to 5.5V Package Thermal Resistance (JA)(Note 3) 8-Pin SOIC 8-Pin MSOP 111.2 C/W 147.4 C/W 5V DC Electrical Characteristics (Note 4) Unless otherwise specified, all limits guaranteed for TA = 25C, V+ = 5V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage TCVOS Input Offset Voltage Drift IBIAS Input Bias Current IOS Input Offset Current CMRR Common Mode Rejection Ratio PSRR CMVR Conditions Typ (Note 5) Max (Note 6) Units 10 150 230 V LMP2232A 0.3 0.5 LMP2232B 0.3 2.5 0.02 3 125 5 0V VCM 4V 81 80 97 Power Supply Rejection Ratio 1.6V V+ 5.5V V- = 0V, VCM = 0V 83 83 120 Common Mode Voltage Range CMRR 80 dB -0.2 -0.2 VO = 0.3V to 4.7V 110 108 CMRR 79 dB AVOL Large Signal Voltage Gain RL = 10 k to VO IO IS Min (Note 6) Output Swing High V+/2 Output Swing Low RL = 10 k to V+/2 VIN(diff) = -100 mV 17 Output Current (Note 7) Sourcing, VO to V- VIN(diff) = 100 mV 27 19 30 Sinking, VO to V+ VIN(diff) = -100 mV 17 12 22 Supply Current dB dB 120 17 19 pA fA 4.2 4.2 RL = 10 k to V+/2 VIN(diff) = 100 mV V/C V dB 50 50 50 50 mV from either rail mA 27 28 A 5V AC Electrical Characteristics (Note 4) Unless otherwise specified, all limits guaranteed for TA = 25C, V+ = 5V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions GBW Gain-Bandwidth Product CL = 20 pF, RL = 10 k SR Slew Rate AV = +1 m Phase Margin www.national.com Typ (Note 5) 130 Falling Edge 33 32 58 Rising Edge 33 32 48 CL = 20 pF, RL = 10 k 2 Min (Note 6) 68 Max (Note 6) Units kHz V/ms deg Parameter Conditions Min (Note 6) Typ (Note 5) Gm Gain Margin CL = 20 pF, RL = 10 k 27 en Input-Referred Voltage Noise Density f = 1 kHz 60 Input Referred Voltage Noise 0.1 Hz to 10 Hz 2.3 in Input-Referred Current Noise f = 1 kHz 10 THD+N Total Harmonic Distortion + Noise f = 100 Hz, RL = 10 k Max (Note 6) Units dB nV/ VPP fA/ 0.002 % 3.3V DC Electrical Characteristics (Note 4) Unless otherwise specified, all limits guaranteed for T A = 25C, V+ = 3.3V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage TCVOS Input Offset Voltage Drift Conditions Min (Note 6) Typ (Note 5) Max (Note 6) Units 10 160 250 V LMP2232A 0.3 0.5 LMP2232B 0.3 2.5 0.02 3 125 IBIAS Input Bias Current IOS Input Offset Current CMRR Common Mode Rejection Ratio 0V VCM 2.3V 79 77 92 PSRR Power Supply Rejection Ratio 1.6V V+ 5.5V V- = 0V, VCM = 0V 83 83 120 CMVR Common Mode Voltage Range CMRR 78 dB -0.2 -0.2 VO = 0.3V to 3V 108 107 Large Signal Voltage Gain RL = 10 k to V+/2 VO IO IS Output Swing High pA 5 CMRR 77 dB AVOL V/C dB dB 2.5 2.5 V 120 RL = 10 k to V+/2 VIN(diff) = 100 mV 14 Output Swing Low RL = 10 k to V+/2 VIN(diff) = -100 mV 14 Output Current (Note 7) Sourcing, VO to V- VIN(diff) = 100 mV 11 8 14 Sinking, VO to V+ VIN(diff) = -100 mV 8 5 11 Supply Current fA 17 dB 50 50 mV from either rail 50 50 mA 25 26 A 3.3V AC Electrical Characteristics (Note 4) Unless otherwise is specified, all limits guaranteed for TA = 25C, V+ = 3.3V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions GBW Gain-Bandwidth Product CL = 20 pF, RL = 10 k 128 SR Slew Rate AV = +1, CL = 20 pF Falling Edge 58 RL = 10 k 48 Rising Edge Min (Note 6) Typ (Note 5) Max (Note 6) Units kHz V/ms m Phase Margin CL = 20 pF, RL = 10 k 66 deg Gm Gain Margin CL = 20 pF, RL = 10 k 26 dB en Input-Referred Voltage Noise Density f = 1 kHz 60 Input-Referred Voltage Noise 0.1 Hz to 10 Hz 2.4 3 nV/ VPP www.national.com LMP2232 Symbol LMP2232 Symbol Parameter in Input-Referred Current Noise THD+N Total Harmonic Distortion + Noise Conditions Min (Note 6) f = 1 kHz Typ (Note 5) Max (Note 6) Units 10 fA/ 0.003 f = 100 Hz, RL = 10 k % 2.5V DC Electrical Characteristics (Note 4) Unless otherwise specified, all limits guaranteed for TA = 25C, V+ = 2.5V, V- = 0V, VCM = VO = V+/2, and RL > 1M. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage TCVOS Input Offset Voltage Drift Conditions Min (Note 6) Typ (Note 5) Max (Note 6) Units 10 190 275 V LMP2232A 0.3 0.5 LMP2232B 0.3 2.5 0.02 3 125 IBias Input Bias Current IOS Input Offset Current CMRR Common Mode Rejection Ratio 0V VCM 1.5V 77 76 91 PSRR Power Supply Rejection Ratio 1.6V V+ 5.5V V- = 0V, VCM = 0V 83 83 120 CMVR Common Mode Voltage Range CMRR 77 dB -0.2 -0.2 VO = 0.3V to 2.2V 104 104 Large Signal Voltage Gain RL = 10 k to V+/2 VO IO IS Output Swing High pA 5 CMRR 76 dB AVOL V/C dB dB 1.7 1.7 V 120 RL = 10 k to V+/2 VIN(diff) = 100 mV 12 Output Swing Low RL = 10 k to V+/2 VIN(diff) = -100 mV 13 Output Current (Note 7) Sourcing, VO to V- VIN(diff) = 100 mV 5 4 8 Sinking, VO to V+ VIN(diff) = -100 mV 3.5 2.5 7 Supply Current fA 16 dB 50 50 50 50 mV from either rail mA 24 25 A 2.5V AC Electrical Characteristics (Note 4) Unless otherwise specified, all limits guaranteed for TA = 25C, V+ = 2.5V, V- = 0V, VCM = VO = V+/2, and RL > 1M. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min Typ (Note 6) (Note 5) GBW Gain-Bandwidth Product CL = 20 pF, RL = 10 k 128 SR Slew Rate AV = +1, CL = 20 pF Falling Edge 58 RL = 10 k Rising Edge 48 m Phase Margin Gm Gain Margin en Input-Referred Voltage Noise Density f = 1 kHz 60 Input-Referred Voltage Noise 0.1 Hz to 10 Hz 2.5 in Input-Referred Current Noise f = 1 kHz 10 THD+N Total Harmonic Distortion + Noise f = 100 Hz, RL = 10 k www.national.com Max (Note 6) Units kHz V/ms CL = 20 pF, RL = 10 k 64 deg CL = 20 pF, RL = 10 k 26 dB 4 0.005 nV/ VPP fA/ % (Note 4) Unless otherwise specified, all limits guaranteed for T A = 25C, V+ = 1.8V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage TCVOS Input Offset Voltage Drift IBIAS Input Bias Current IOS Input Offset Current CMRR Common Mode Rejection Ratio PSRR CMVR Conditions Typ (Note 5) Max (Note 6) Units 10 230 325 V LMP2232A 0.3 0.5 LMP2232B 0.3 2.5 0.02 3 125 0V VCM 0.8V Power Supply Rejection Ratio 1.6V V+ 5.5V V- = 0V, VCM = 0V 83 83 120 Common Mode Voltage Range CMRR 76 dB -0.2 0 VO = 0.3V to 1.5V 103 103 RL = 10 k to V+/2 VO IO IS Output Swing High pA fA 92 Large Signal Voltage Gain V/C 5 76 75 CMRR 75 dB AVOL Min (Note 6) dB 1.0 1.0 V 120 RL = 10 k to V+/2 VIN(diff) = 100 mV 12 Output Swing Low RL = 10 k to V+/2 VIN(diff) = -100 mV 13 Output Current (Note 7) Sourcing, VO to V- VIN(diff) = 100 mV 2.5 2 5 Sinking, VO to V+ VIN(diff) = -100 mV 2 1.5 5 Supply Current dB dB 50 50 mV from either rail 50 50 mA 16 24 25 A 1.8V AC Electrical Characteristics (Note 4) Unless otherwise is specified, all limits guaranteed for TA = 25C, V+ = 1.8V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions GBW Gain-Bandwidth Product CL = 20 pF, RL = 10 k 127 SR Slew Rate AV = +1, CL = 20 pF Falling Edge 58 RL = 10 k 48 Rising Edge Min (Note 6) Typ (Note 5) m Phase Margin Gm Gain Margin en Input-Referred Voltage Noise Density f = 1 kHz 60 Input-Referred Voltage Noise 0.1 Hz to 10 Hz 2.4 in Input-Referred Current Noise f = 1 kHz 10 THD+N Total Harmonic Distortion + Noise f = 100 Hz, RL = 10 k Max (Note 6) Units kHz V/ms CL = 20 pF, RL = 10 k 60 deg CL = 20 pF, RL = 10 k 25 dB 5 0.005 nV/ VPP fA/ % www.national.com LMP2232 1.8V DC Electrical Characteristics LMP2232 Note 1: Absolute Maximum Ratings indicate limits beyond which damage may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC). Note 3: The maximum power dissipation is a function of TJ(MAX), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ JA. All numbers apply for packages soldered directly onto a PC board. Note 4: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond which the device may be permanently degraded, either mechanically or electrically. Note 5: Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material. Note 6: All limits are guaranteed by testing, statistical analysis or design. Note 7: The short circuit test is a momentary open loop test. Connection Diagram 8-Pin MSOP/SOIC 30033938 Top View Ordering Information Package Part Number Temperature Range Package Marking Transport Media LMP2232AMA 250 Units Tape and Reel LMP2232AMA 95 Units/Rail LMP2232AMAE 8-Pin SOIC LMP2232AMAX 2.5k Units Tape and Reel LMP2232BMA 95 Units/Rail LMP2232BMAE LMP2232BMAX LMP2232AMM LMP2232BMA -40C to 125C 250 Units Tape and Reel 1k Units Tape and Reel AK5A 250 Units Tape and Reel LMP2232AMMX 3.5k Units Tape and Reel LMP2232BMM 1k Units Tape and Reel LMP2232BMME AK5B LMP2232BMMX www.national.com M08A 2.5k Units Tape and Reel LMP2232AMME 8-Pin MSOP NSC Drawing 250 Units Tape and Reel 3.5k Units Tape and Reel 6 MUA08A Unless otherwise Specified: TA = 25C, VS = 5V, VCM = VS/2, where Offset Voltage Distribution TCVOS Distribution 30033907 30033911 Offset Voltage Distribution TCVOS Distribution 30033906 30033910 Offset Voltage Distribution TCVOS Distribution 30033905 30033909 7 www.national.com LMP2232 Typical Performance Characteristics VS = V+ - V- LMP2232 Offset Voltage Distribution TCVOS Distribution 30033969 30033973 Offset Voltage vs. VCM Offset Voltage vs. VCM 30033918 30033965 Offset Voltage vs. VCM Offset Voltage vs. VCM 30033964 www.national.com 30033972 8 LMP2232 Offset Voltage vs. Temperature Offset Voltage vs. Supply Voltage 30033971 30033970 0.1 Hz to 10 Hz Voltage Noise 0.1 Hz to 10 Hz Voltage Noise 30033933 30033934 0.1 Hz to 10 Hz Voltage Noise 0.1 Hz to 10 Hz Voltage Noise 30033932 30033931 9 www.national.com LMP2232 Input Bias Current vs. VCM Input Bias Current vs. VCM 30033955 30033956 Input Bias Current vs. VCM Input Bias Current vs. VCM 30033957 30033958 Input Bias Current vs. VCM Input Bias Current vs. VCM 30033959 www.national.com 30033960 10 LMP2232 Input Bias Current vs. VCM Input Bias Current vs. VCM 30033961 30033962 PSRR vs. Frequency Supply Current vs. Supply Voltage (per channel) 30033966 30033912 Sinking Current vs. Supply Voltage Sourcing Current vs. Supply Voltage 30033913 30033914 11 www.national.com LMP2232 Output Swing High vs. Supply Voltage Output Swing Low vs. Supply Voltage 30033915 30033916 Open Loop Frequency Response Open Loop Frequency Response 30033921 30033922 Phase Margin vs. Capacitive Load Slew Rate vs. Supply Voltage 30033963 www.national.com 30033930 12 LMP2232 THD+N vs. Amplitude THD+N vs. Frequency 30033929 30033928 Large Signal Step Response Small Signal Step Response 30033924 30033923 Large Signal Step Response Small Signal Step Response 30033926 30033925 13 www.national.com LMP2232 CMRR vs. Frequency Input Voltage Noise vs. Frequency 30033919 30033967 www.national.com 14 LMP2232 Application Information LMP2232 The LMP2232 is a quad CMOS precision amplifier that offers low offset voltage, low offset voltage drift, and high gain while consuming less than 10 A of supply current per channel. The LMP2232 is a micropower op amp, consuming only 36 A of current. Micropower op amps extend the run time of battery powered systems and reduce energy consumption in energy limited systems. The guaranteed supply voltage range of 1.8V to 5.0V along with the ultra-low supply current extend the battery run time in two ways. The extended guaranteed power supply voltage range of 1.8V to 5.0V enables the op amp to function when the battery voltage has depleted from its nominal value down to 1.8V. In addition, the lower power consumption increases the life of the battery. The LMP2232 has input referred offset voltage of only 150 V maximum at room temperature. This offset is guaranteed to be less than 230 V over temperature. This minimal offset voltage along with very low TCVOS of only 0.3 V/ C typical allows more accurate signal detection and amplification in precision applications. The low input bias current of only 20 fA gives the LMP2232 superiority for use in high impedance sensor applications. Bias current of an amplifier flows through source resistance of the sensor and the voltage resulting from this current flow appears as a noise voltage on the input of the amplifier. The low input bias current enables the LMP2232 to interface with high impedance sensors while generating negligible voltage noise. Thus the LMP2232 provides better signal fidelity and a higher signal-to-noise ratio when interfacing with high impedance sensors. National Semiconductor is heavily committed to precision amplifiers and the market segments they serve. Technical support and extensive characterization data is available for sensitive applications or applications with a constrained error budget. The operating voltage range of 1.6V to 5.5V over the extensive temperature range of -40C to 125C makes the LMP2232 an excellent choice for low voltage precision applications with extensive temperature requirements. The LMP2232 is offered in the 8-pin MSOP and 8-pin SOIC packages. These small packages are ideal solutions for area constrained PC boards and portable electronics. The input current noise of the LMP2232 is so low that it will not become the dominant factor in the total noise unless source resistance exceeds 300 M, which is an unrealistically high value. As is evident in Figure 1, at lower RS values, total noise is dominated by the amplifier's input voltage noise. Once RS is larger than a 100 k, then the dominant noise factor becomes the thermal noise of RS. As mentioned before, the current noise will not be the dominant noise factor for any practical application. 30033948 FIGURE 1. Total Input Noise VOLTAGE NOISE REDUCTION . While The LMP2232 has an input voltage noise of 60nV/ this value is very low for micropower amplifiers, this input voltage noise can be further reduced by placing N amplifiers in parallel as shown in Figure 2. The total voltage noise on the output of this circuit is divided by the square root of the number of amplifiers used in this parallel combination. This is because each individual amplifier acts as an independent noise source, and the average noise of independent sources is the quadrature sum of the independent sources divided by the number of sources. For N identical amplifiers, this means: TOTAL NOISE CONTRIBUTION The LMP2232 has very low input bias current, very low input current noise, and low input voltage noise for micropower amplifiers. As a result, these amplifiers make great choices for circuits with high impedance sensor applications. Figure 1 shows the typical input noise of the LMP2232 as a function of source resistance where: en denotes the input referred voltage noise ei is the voltage drop across source resistance due to input referred current noise or ei = RS * in et shows the thermal noise of the source resistance eni shows the total noise on the input. Where: 15 www.national.com LMP2232 Figure 2 shows a schematic of this input voltage noise reduction circuit. Typical resistor values are: RG = 10, RF = 1 k, and RO = 1 k. 30033936 FIGURE 3. Instrumentation Amplifier There are two stages in this amplifier. The last stage, output stage, is a differential amplifier. In an ideal case the two amplifiers of the first stage, the input stage, would be set up as buffers to isolate the inputs. However they cannot be connected as followers because of mismatch of amplifiers. That is why there is a balancing resistor between the two. The product of the two stages of gain will give the gain of the instrumentation amplifier. Ideally, the CMRR should be infinite. However the output stage has a small non-zero common mode gain which results from resistor mismatch. In the input stage of the circuit, current is the same across all resistors. This is due to the high input impedance and low input bias current of the LMP2232. 30033946 (1) FIGURE 2. Noise Reduction Circuit By Ohm's Law: PRECISION INSTRUMENTATION AMPLIFIER Measurement of very small signals with an amplifier requires close attention to the input impedance of the amplifier, gain of the signal on the inputs, and the gain on each input of the amplifier. This is because the difference of the input signal on the two inputs is of the interest and the common signal is considered noise. A classic circuit implementation is an instrumentation amplifier. Instrumentation amplifiers have a finite, accurate, and stable gain. They also have extremely high input impedances and very low output impedances. Finally they have an extremely high CMRR so that the amplifier can only respond to the differential signal. A typical instrumentation amplifier is shown in Figure 3. (2) However: (3) So we have: VO1-VO2 = (2a+1)(V1-V2) (4) Now looking at the output of the instrumentation amplifier: (5) Substituting from Equation 4: (6) This shows the gain of the instrumentation amplifier to be: -K(2a+1) Typical values for this circuit can be obtained by setting: a = 12 and K= 4. This results in an overall gain of -100. www.national.com 16 30033951 30033950 FIGURE 4. Bridge Sensor Instrumentation amplifiers are great for interfacing with bridge sensors. Bridge sensors often sense a very small differential signal in the presence of a larger common mode voltage. Instrumentation amplifiers reject this common mode signal. Figure 5 shows a strain gauge bridge amplifier. In this application one of the LMP2232 amplifiers is used to buffer the LM4140A's precision output voltage. The LM4140A is a precision voltage reference. The other three amplifiers in the LMP2232 are used to form an instrumentation amplifier. This instrumentation amplifier uses the LMP2232's high CMRR and low VOS and TCVOS to accurately amplify the small differential signal generated by the output of the bridge sensor. This amplified signal is then fed into the ADC121S021 which is a 12-bit analog to digital converter. This circuit works on a single supply voltage of 5V. 17 www.national.com LMP2232 of two adjacent resistor values are equal. This fact is used in null circuit measurements. These are particularly used in feedback systems which involve electrochemical elements or human interfaces. Null systems force an active resistor, such as a strain gauge, to balance the bridge by influencing the measured parameter. Often in sensor applications at lease one of the resistors is a variable resistor, or a sensor. The deviation of this active element from its initial value is measured as an indication of change in the measured quantity. A change in output voltage represents the sensor value change. Since the sensor value change is often very small, the resulting output voltage is very small in magnitude as well. This requires an extensive and very precise amplification circuitry so that signal fidelity does not change after amplification. Sensitivity of a bridge is the ratio of its maximum expected output change to the excitation voltage change. Figure 4(a) shows a typical bridge sensor and Figure 4(b) shows the bridge with four sensors. R in Figure 4(b) is the nominal value of the sense resistor and the deviations from R are proportional to the quantity being measured. SINGLE SUPPLY STRAIN GAGE BRIDGE AMPLIFIER Strain gauges are popular electrical elements used to measure force or pressure. Strain gauges are subjected to an unknown force which is measured as the deflection on a previously calibrated scale. Pressure is often measured using the same technique; however this pressure needs to be converted into force using an appropriate transducer. Strain gauges are often resistors which are sensitive to pressure or to flexing. Sense resistor values range from tens of ohms to several hundred kilo-ohms. The resistance change which is a result of applied force across the strain gauge might be 1% of its total value. An accurate and reliable system is needed to measure this small resistance change. Bridge configurations offer a reliable method for this measurement. Bridge sensors are formed of four resistors, connected as a quadrilateral. A voltage source or a current source is used across one of the diagonals to excite the bridge while a voltage detector across the other diagonal measures the output voltage. Bridges are mainly used as null circuits or to measure differential voltages. Bridges will have no output voltage if the ratios LMP2232 30033974 FIGURE 5. Strain Gage Bridge Amplifier or specify a range of acceptable values for the load resistor. Oxygen sensors typically have a life of one to two years. The use of the micropower LMP2232 means minimal power usage by the op amp and it enhances the battery life. Depending on other components present in the circuit design, the battery could last for the entire life of the oxygen sensor. The precision specifications of the LMP2232, such as its very low offset voltage, low TCVOS, low input bias current, low CMRR, and low PSRR are other factors which make the LMP2232 a great choice for this application.. PORTABLE GAS DETECTION SENSOR Gas sensors are used in many different industrial and medical applications. They generate a current which is proportional to the percentage of a particular gas sensed in an air sample. This current goes through a load resistor and the resulting voltage drop is measured. Depending on the sensed gas and sensitivity of the sensor, the output current can be in the order of tens of microamperes to a few milliamperes. Gas sensor datasheets often specify a recommended load resistor value or they suggest a range of load resistors to choose from. Oxygen sensors are used when air quality or oxygen delivered to a patient needs to be monitored. Fresh air contains 20.9% oxygen. Air samples containing less than 18% oxygen are considered dangerous. Oxygen sensors are also used in industrial applications where the environment must lack oxygen. An example is when food is vacuum packed. There are two main categories of oxygen sensors, those which sense oxygen when it is abundantly present (i.e. in air or near an oxygen tank) and those which detect very small traces of oxygen in ppm. Figure 6 shows a typical circuit used to amplify the output signal of an oxygen detector. The LMP2232 makes an excellent choice for this application as it draws only 36 A of current and operates on supply voltages down to 1.8V. This application detects oxygen in air. The oxygen sensor outputs a known current through the load resistor. This value changes with the amount of oxygen present in the air sample. Oxygen sensors usually recommend a particular load resistor value www.national.com 30033949 FIGURE 6. Precision Oxygen Sensor 18 LMP2232 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin MSOP NS Package Number MUA08A 8-Pin SOIC NS Package Number M08A 19 www.national.com LMP2232 Dual, Micropower, 1.6V, Precision, Operational Amplifier with CMOS Input Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy PowerWise(R) Solutions www.national.com/powerwise Solutions www.national.com/solutions Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero Temperature Sensors www.national.com/tempsensors Solar Magic(R) www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless Analog University(R) www.national.com/AU THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated