LM2900, LM3900 QUADRUPLE NORTON OPERATIONAL AMPLIFIERS SLOS059 - JULY 1979 - REVISED SEPTEMBER 1990 D D D D D D D N PACKAGE (TOP VIEW) Wide Range of Supply Voltages, Single or Dual Supplies Wide Bandwidth Large Output Voltage Swing Output Short-Circuit Protection Internal Frequency Compensation Low Input Bias Current Designed to Be Interchangeable With National Semiconductor LM2900 and LM3900, Respectively 1IN + 2IN + 2IN - 2OUT 1OUT 1IN - GND 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC 3IN + 4IN + 4IN - 4OUT 3OUT 3IN - description These devices consist of four independent, highgain frequency-compensated Norton operational amplifiers that were designed specifically to operate from a single supply over a wide range of voltages. Operation from split supplies is also possible. The low supply current drain is essentially independent of the magnitude of the supply voltage. These devices provide wide bandwidth and large output voltage swing. symbol (each amplifier) + IN + OUT - IN - The LM2900 is characterized for operation from - 40C to 85C, and the LM3900 is characterized for operation from 0C to 70C. schematic (each amplifier) VCC Constant Current Generator 200 A OUT IN - 1.3 mA IN + Copyright 1990, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 LM2900, LM3900 QUADRUPLE NORTON OPERATIONAL AMPLIFIERS SLOS059 - JULY 1979 - REVISED SEPTEMBER 1990 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) LM2900 LM3900 UNIT Supply voltage, VCC (see Note 1) 36 36 V Input current 20 20 mA unlimited unlimited Duration of output short circuit (one amplifier) to ground at (or below) 25C free-air temperature (see Note 2) Continuous total dissipation See Dissipation Rating Table Operating free-air temperature range - 40 to 85 0 to 70 C Storage temperature range - 65 to 150 - 65 to 150 C 260 260 C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds NOTES: 1. All voltage values, except differential voltages, are with respect to the network ground terminal. 2. Short circuits from outputs to VCC can cause excessive heating and eventual destruction. DISSIPATION RATING TABLE PACKAGE N TA 25C POWER RATING 1150 mW DERATING FACTOR ABOVE TA = 25C 9.2 mW/C TA = 70C POWER RATING TA = 85C POWER RATING 736 mW 598 mW recommended operating conditions LM2900 Supply voltage, VCC (single supply) LM3900 UNIT MIN MAX MIN MAX 4.5 32 4.5 32 V V Supply voltage, VCC + (dual supply) 2.2 16 2.2 16 Supply voltage, VCC - (dual supply) - 2.2 - 16 - 2.2 - 16 V -1 mA Input current (see Note 3) -1 Operating free-air temperature, TA - 40 85 0 70 C NOTE 3: Clamp transistors are included that prevent the input voltages from swinging below ground more than approximately - 0.3 V. The negative input currents that may result from large signal overdrive with capacitive input coupling must be limited externally to values of approximately - 1 mA. Negative input currents in excess of - 4 mA causes the output voltage to drop to a low voltage. These values apply for any one of the input terminals. If more than one of the input terminals are simultaneously driven negative, maximum currents are reduced. Common-mode current biasing can be used to prevent negative input voltages. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 LM2900, LM3900 QUADRUPLE NORTON OPERATIONAL AMPLIFIERS SLOS059 - JULY 1979 - REVISED SEPTEMBER 1990 electrical characteristics, VCC = 15 V, TA = 25C (unless otherwise noted) IIB LM2900 TEST CONDITIONS PARAMETER Input bias current (inverting input) II + = 0 MIN Change in mirror gain MAX 30 200 TA = 25C TA = Full range II+ = 20 A to 200 A TA = Full range, range See Note 4 Mirror gain LM3900 TYP MIN 300 09 0.9 TYP MAX 30 200 300 11 1.1 09 0.9 11 1.1 2% 5% 2% 5% 10 500 10 500 UNIT nA A/A Mirror current VI + = VI -, See Note 4 g , TA = Full range, AVD Large-signal differential voltage amplification VO = 10 V, f = 100 Hz RL = 10 k, ri Input resistance (inverting input) 1 1 M ro Output resistance 8 8 k B1 Unity-gain bandwidth (inverting input) 2.5 2.5 MHz kSVR Supply voltage rejection ratio (VCC /VIO) 70 70 dB VOH High-level output voltage III+ = 0 0, II - = 0 VOL Low-level output voltage II + = 0, RL = 2 k II - = 10 A, IOS Short-circuit output current (output internally high) II + = 0, VO = 0 II - = 0, 1.2 RL = 2 k 1.2 13.5 VCC = 30 V, No load Pulldown current 2.8 2.8 A V/mV 13.5 29.5 0.09 V 29.5 0.2 0.09 0.2 V -6 - 18 -6 - 10 mA 0.5 1.3 0.5 1.3 mA IOL II - = 5 A VOL = 1 V 5 5 mA ICC Supply current (four amplifiers) No load 6.2 10 6.2 10 mA All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. Full range for TA is - 40C to 85C for LM2900 and 0C to 70C for LM3900. The output current-sink capability can be increased for large-signal conditions by overdriving the inverting input. NOTE 4: These parameters are measured with the output balanced midway between VCC and GND. Low-level output current operating characteristics, VCC = 15 V, TA = 25C PARAMETER SR Slew rate at unity gain TEST CONDITIONS Low-to-high output High-to-low output V VO = 10 V, POST OFFICE BOX 655303 pF CL = 100 pF, * DALLAS, TEXAS 75265 RL = 2 k MIN TYP 0.5 20 MAX UNIT V/s 3 LM2900, LM3900 QUADRUPLE NORTON OPERATIONAL AMPLIFIERS SLOS059 - JULY 1979 - REVISED SEPTEMBER 1990 TYPICAL CHARACTERISTICS INPUT BIAS CURRENT (INVERTING INPUT) vs FREE-AIR TEMPERATURE MIRROR GAIN vs FREE-AIR TEMPERATURE 1.2 80 VCC = 15 V VO = 7.5 V II + = 0 VCC = 15 V II + = 10 A 1.15 1.1 60 II - /I + - Mirror Gain IIB - Input Bias Current - nA 70 50 40 30 1.05 1 0.95 20 0.9 10 0.85 0 - 75 - 50 - 25 0 25 50 75 TA - Free-Air Temperature - C 0.8 - 75 100 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C Figure 1 Figure 2 LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs SUPPLY VOLTAGE LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREQUENCY 104 104 VCC = 15 V TA = 25C AVD - Differential Voltage Amplification AVD - Differential Voltage Amplification RL 10 k 103 RL = 2 k 102 10 1 100 1k 10 k 100 k 1M 10 M 103 102 10 RL = 10 k TA = 25C 1 0 5 10 15 20 25 VCC - Supply Voltage - V f - Frequency - Hz Figure 3 Figure 4 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 4 125 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 30 LM2900, LM3900 QUADRUPLE NORTON OPERATIONAL AMPLIFIERS SLOS059 - JULY 1979 - REVISED SEPTEMBER 1990 TYPICAL CHARACTERISTICS LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE SUPPLY VOLTAGE REJECTION RATIO vs FREQUENCY 100 KSVR - Supply Voltage Rejection Ratio - dB AVD - Differential Voltage Amplification 104 103 102 10 VCC = 15 V VO = 10 V RL = 10 k 1 - 75 - 50 - 25 0 25 50 75 100 VCC = 15 V TA = 25C 90 80 70 60 50 40 30 20 10 0 100 125 400 1 k TA - Free-Air Temperature - C SHORT-CIRCUIT OUTPUT CURRENT (OUTPUT INTERNALLY HIGH) vs SUPPLY VOLTAGE PEAK-TO-PEAK OUTPUT VOLTAGE vs FREQUENCY 16 30 VCC = 15 V RL = 2 k II + = 0 TA = 25C 14 12 IOS - Short-Circuit Output Current - mA VO(PP) - Peak-To-Peak Output Voltage - V 40 k 100 k 400 k 1 M Figure 6 Figure 5 10 8 6 AA AA AA 4 2 0 1k 4k 10 k f - Frequency - Hz 10 k 100 k 1M 10 M VO = 0 II + = 0 II - = 0 25 TA = 0C 20 TA = 25C 15 10 5 0 0 5 f - Frequency - Hz Figure 7 10 15 20 VCC - Supply Voltage - V 25 30 Figure 8 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 LM2900, LM3900 QUADRUPLE NORTON OPERATIONAL AMPLIFIERS SLOS059 - JULY 1979 - REVISED SEPTEMBER 1990 TYPICAL CHARACTERISTICS LOW-LEVEL OUTPUT CURRENT vs SUPPLY VOLTAGE PULLDOWN CURRENT vs SUPPLY VOLTAGE 2 VOL = 1 V II + = 0 TA = 25C 50 1.8 II - = 100 A 40 30 20 II - = 10 A 10 0 5 1.4 TA = 25C 1.2 1 TA = 85C 0.8 0.6 0.4 II - = 5 A 0 TA = - 40C 1.6 Pulldown Current - mA IOL- Low-Level Output Current - mA 60 0.2 10 15 20 VCC - Supply Voltage - V 25 0 30 0 5 10 15 20 VCC - Supply Voltage - V 25 30 Figure 10 Figure 9 TOTAL SUPPLY CURRENT vs SUPPLY VOLTAGE PULLDOWN CURRENT vs FREE-AIR TEMPERATURE 8 2 VCC = 15 V 1.8 7 I CC - Total Supply Current - mA Pulldown Current - mA 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0 - 75 - 50 - 25 0 25 50 75 100 125 6 5 4 3 2 TA = 25C No Signal No Load 1 0 0 5 TA - Free-Air Temperature -C 10 15 20 25 30 VCC - Supply Voltage - V Figure 11 Figure 12 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 LM2900, LM3900 QUADRUPLE NORTON OPERATIONAL AMPLIFIERS SLOS059 - JULY 1979 - REVISED SEPTEMBER 1990 APPLICATION INFORMATION Norton (or current-differencing) amplifiers can be used in most standard general-purpose operational amplifier applications. Performance as a dc amplifier in a single-power-supply mode is not as precise as a standard integrated-circuit operational amplifier operating from dual supplies. Operation of the amplifier can best be understood by noting that input currents are differenced at the inverting input terminal and this current then flows through the external feedback resistor to produce the output voltage. Common-mode current biasing is generally useful to allow operating with signal levels near (or even below) ground. Internal transistors clamp negative input voltages at approximately - 0.3 V but the magnitude of current flow has to be limited by the external input network. For operation at high temperature, this limit should be approximately - 100 A. Noise immunity of a Norton amplifier is less than that of standard bipolar amplifiers. Circuit layout is more critical since coupling from the output to the noninverting input can cause oscillations. Care must also be exercised when driving either input from a low-impedance source. A limiting resistor should be placed in series with the input lead to limit the peak input current. Current up to 20 mA will not damage the device, but the current mirror on the noninverting input will saturate and cause a loss of mirror gain at higher current levels, especially at high operating temperatures. V+ 1 M 10 k 1 M 1 k 1 M - Input 30 k 100 k + Output 91 k IO 1 mA per input volt Figure 13. Voltage-Controlled Current Source V+ 1 M 1 M - Output 100 k + Input 100 k 1 k IO 1 mA per input volt Figure 14. Voltage-Controlled Current Sink POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 PACKAGE OPTION ADDENDUM www.ti.com 23-Apr-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty LM2900D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2900N ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM2900N ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM2900N ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM2900NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM2900NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM2900NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM3900D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Lead/Ball Finish MSL Peak Temp (3) PACKAGE OPTION ADDENDUM www.ti.com 23-Apr-2007 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty LM3900DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM3900N ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM3900N ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM3900N ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM3900NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM3900NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LM3900NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 23-Apr-2007 TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM2900DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 LM3900DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2900DR SOIC D 14 2500 367.0 367.0 38.0 LM3900DR SOIC D 14 2500 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated