EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 1 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
Technical Data Sheet
Full Color Chip LED
15-23BSURSYGUBC/S530-A2/TR8
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Multi-color type.
․Pb-free.
Descriptions
․The 15-23B SMD Taping is much smaller
than lead frame type components, thus
enable smaller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Chip
Type Material Emitted Color Lens Color
SUR AlGaInP Hyper Red
SYG AlGaInP Super Yellow Green
UB GaN/SiC Blue
Water Clear
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 2 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Package Outline Dimensions
0.9
Anode mark
0.6
0.9
2.0
2.0
0.4
2.4
1.1
2.6
3.2
-
Blue
Green
Red
-
-
4.8
1.8
+
Note: The tolerances unless mentioned is ±0.1mm,Unit = mm
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 3 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Absolute Maximum Ratings (Ta=25℃)
Parameter Symbol Rating Unit
Reverse Voltage VR 5 V
Forward Current IF
SUR:25
SYG:25
UB:30
mA
Operating Temperature Topr -40 ~ +85 ℃
Storage Temperature Tstg -40 ~ +90 ℃
Soldering Temperature Tsol 260 (for 5
seconds) ℃
Electrostatic Discharge ESD
SUR:2000
SYG:2000
UB:1000
V
Power Dissipation Pd
SUR:60
SYG:60
UB:140
mW
Peak Forward Current
(Duty 1/10 @1KHz) IFP
SUR:60
SYG:60
UB:70
mA
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 4 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Electro-Optical Characteristics (Ta=25℃)
Parameter Symbol Min. Typ. Max. Unit Condition
Luminous Intensity
SUR
Iv SYG
UB
17
11
9.0
40
17
15
----- mcd IF=20mA
Viewing Angle 2θ1/2 ----- 120 ----- deg IF=20mA
Peak Wavelength
SUR
λp SYG
UB
-----
632
575
428
----- nm IF=20mA
Dominant Wavelength
SUR
λd SYG
UB
-----
624
573
466
----- nm IF=20mA
Spectrum Radiation
Bandwidth
SUR
△λ SYG
UB
-----
20
20
65
----- nm IF=20mA
Forward Voltage
SUR
VF SYG
UB
-----
2.0
2.0
3.8
2.4
2.4
4.5
V IF=20mA
Reverse Current
SUR
IR SYG
UB
----- -----
10
10
50
μA VR=5V
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 5 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Typical Electro-Optical Characteristics Curves
SUR
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 6 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Typical Electro-Optical Characteristics Curves
SYG
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 7 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Typical Electro-Optical Characteristics Curves
UB
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 8 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 9 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Aluminum moistue-proof bag LabelDesiccant
Label
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 10 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level：90%
LTPD：10%
No. Items Test Condition
Test
Hours/Cycles Sample
Size Ac/Re
1 Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec. 6 Min. 22 PCS. 0/1
2 Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles 22 PCS. 0/1
3 Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles 22 PCS. 0/1
4 High Temperature
Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1
5 Low Temperature
Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1
6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1
7 High Temperature /
High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 11 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of the
hand solder.
EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 12 of 12
Device No. : DSE-153- Prepared date: 08-04-2004 Prepared by : Kenny Wang
15-23BSURSYGUBC/S530-A2/TR8
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
E
VERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com
