BZX79C2V4RL Series 500 mW DO-35 Hermetically Sealed Glass Zener Voltage Regulators This is a complete series of 500 mW Zener diodes with limits and excellent operating characteristics that reflect the superior capabilities of silicon-oxide passivated junctions. All this in an axial-lead hermetically sealed glass package that offers protection in all common environmental conditions. http://onsemi.com Cathode Anode Specification Features: * Zener Voltage Range - 2.4 V to 33 V * ESD Rating of Class 3 (>16 KV) per Human Body Model * DO-204AH (DO-35) Package - Smaller than Conventional DO-204AA Package * Double Slug Type Construction * Metallurgical Bonded Construction AXIAL LEAD CASE 299 GLASS Mechanical Characteristics: CASE: Double slug type, hermetically sealed glass FINISH: All external surfaces are corrosion resistant and leads are MARKING DIAGRAM readily solderable L 79C xxx YWW MAXIMUM LEAD TEMPERATURE FOR SOLDERING PURPOSES: 230C, 1/16 from the case for 10 seconds POLARITY: Cathode indicated by polarity band MOUNTING POSITION: Any MAXIMUM RATINGS (Note 1.) Rating Max. Steady State Power Dissipation @ TL 75C, Lead Length = 3/8 Derate above 75C Operating and Storage Temperature Range Symbol Value Unit PD 500 mW 4.0 mW/C -65 to +200 C TJ, Tstg L = Assembly Location 79Cxxx = Device Code = (See Table Next Page) Y = Year WW = Work Week ORDERING INFORMATION Device Package Shipping BZX79CxxxRL Axial Lead 5000/Tape & Reel BZX79CxxxRL2* Axial Lead 5000/Tape & Reel 1. Some part number series have lower JEDEC registered ratings. * The "2" suffix refers to 26 mm tape spacing. Semiconductor Components Industries, LLC, 2001 May, 2001 - Rev. 1 1 Publication Order Number: BZX79C2V4RL/D BZX79C2V4RL Series ELECTRICAL CHARACTERISTICS (TL = 30C unless otherwise noted, VF = 1.5 V Max @ IF = 100 mA for all types) Symbol IF Parameter VZ Reverse Zener Voltage @ IZT IZT Reverse Current ZZT Maximum Zener Impedance @ IZT VBR I VZ VR V Temperature Coefficient of VBR (Typical) IR Reverse Leakage Current (TA = 25C) @ VR VR Breakdown Voltage IF Forward Current VF Forward Voltage @ IF C Capacitance (Typical) IR VF IZT Zener Voltage Regulator ELECTRICAL CHARACTERISTICS (TL = 30C unless otherwise noted, VF = 1.5 V Max @ IF = 100 mA for all types) Leakage Current VBR IR @ VR mV/C @ IZT ZZT (Note 4.) @ IZT (f = 1.0 kHz) Max mA A Volts Min Max pF 2.4 2.7 3.0 3.3 3.6 2.52 2.84 3.15 3.47 3.78 5 5 5 5 5 100 100 95 95 90 100 75 50 25 15 1 1 1 1 1 -3.5 -3.5 -3.5 -3.5 -3.5 0 0 0 0 0 255 230 215 200 185 3.71 4.47 4.85 5.32 5.89 3.9 4.7 5.1 5.6 6.2 4.10 4.94 5.36 5.88 6.51 5 5 5 5 5 90 80 60 40 10 10 3 2 1 3 1 2 2 2 4 -3.5 -3.5 -2.7 -2.0 0.4 0.3 0.2 1.2 2.5 3.7 175 130 110 95 90 79C6V8 79C7V5 79C8V2 79C10 79C12 6.46 7.13 7.79 9.5 11.4 6.8 7.5 8.2 10 12 7.19 7.88 8.61 10.5 12.6 5 5 5 5 5 15 15 15 20 25 2 1 0.7 0.2 0.1 4 5 5 7 8 1.2 2.5 3.2 4.5 6.0 4.5 5.3 6.2 8.0 10 85 80 75 70 65 BZX79C15RL BZX79C16RL BZX79C18RL BZX79C22RL BZX79C24RL 79C15 79C16 79C18 79C22 79C24 14.25 15.2 17.1 20.9 22.8 15 16 18 22 24 15.75 16.8 18.9 23.1 25.2 5 5 5 5 5 30 40 45 55 70 0.05 0.05 0.05 0.05 0.05 10.5 11.2 12.6 15.4 16.8 9.2 10.4 12.9 16.4 18.4 13 14 16 20 22 55 52 47 34 33 BZX79C27RL BZX79C30RL BZX79C33RL 79C27 79C30 79C33 25.65 28.5 31.35 27 30 33 28.35 31.5 34.65 5 5 5 80 80 80 0.05 0.05 0.05 18.9 21 23.1 - - - 23.5 26 29 30 27 25 Zener Voltage (Note 3.) VZ (Volts) Device (Note 2.) Device Marking Min Nom BZX79C2V4RL BZX79C2V7RL BZX79C3V0RL BZX79C3V3RL BZX79C3V6RL 79C2V4 79C2V7 79C3V0 79C3V3 79C3V6 2.28 2.57 2.85 3.14 3.42 BZX79C3V9RL BZX79C4V7RL BZX79C5V1RL BZX79C5V6RL BZX79C6V2RL 79C3V9 79C4V7 79C5V1 79C5V6 79C6V2 BZX79C6V8RL BZX79C7V5RL BZX79C8V2RL BZX79C10RL BZX79C12RL C VZ = 0 0, f = 1.0 MHz 2. TOLERANCE AND VOLTAGE DESIGNATION Tolerance designation - the type numbers listed have zener voltage min/max limits as shown. 3. REVERSE ZENER VOLTAGE (VZ) MEASUREMENT Reverse zener voltage is measured under pulse conditions such that TJ is no more than 2C above TA. 4. ZENER IMPEDANCE (ZZ) DERIVATION ZZT and ZZK are measured by dividing the ac voltage drop across the device by the ac current applied. The specified limits are for I Z(ac) = 0.1 IZ(dc) with the ac frequency = 1.0 kHz. http://onsemi.com 2 BZX79C2V4RL Series PD, STEADY STATE POWER DISSIPATION (WATTS) 0.7 HEAT SINKS 0.6 0.5 0.4 3/8" 3/8" 0.3 0.2 0.1 0 0 20 40 60 80 100 120 140 160 TL, LEAD TEMPERATURE (C) Figure 1. Steady State Power Derating http://onsemi.com 3 180 200 BZX79C2V4RL Series JL , JUNCTIONTOLEAD THERMAL RESISTANCE (C/W) APPLICATION NOTE -- ZENER VOLTAGE Since the actual voltage available from a given zener diode is temperature dependent, it is necessary to determine junction temperature under any set of operating conditions in order to calculate its value. The following procedure is recommended: Lead Temperature, TL, should be determined from: TL = LAPD + TA. LA is the lead-to-ambient thermal resistance (C/W) and PD is the power dissipation. The value for LA will vary and depends on the device mounting method. LA is generally 30 to 40C/W for the various clips and tie points in common use and for printed circuit board wiring. The temperature of the lead can also be measured using a thermocouple placed on the lead as close as possible to the tie point. The thermal mass connected to the tie point is normally large enough so that it will not significantly respond to heat surges generated in the diode as a result of pulsed operation once steady-state conditions are achieved. Using the measured value of TL, the junction temperature may be determined by: 500 400 L L 300 2.4-60V 200 62-200V 100 0 0 0.2 0.4 0.6 0.8 1 L, LEAD LENGTH TO HEAT SINK (INCH) Figure 2. Typical Thermal Resistance 1000 7000 5000 TYPICAL LEAKAGE CURRENT AT 80% OF NOMINAL BREAKDOWN VOLTAGE 2000 1000 700 500 TJ = TL + TJL. TJL is the increase in junction temperature above the lead temperature and may be found from Figure 2 for dc power: 200 TJL = JLPD. I R , LEAKAGE CURRENT ( A) For worst-case design, using expected limits of IZ, limits of PD and the extremes of TJ(TJ) may be estimated. Changes in voltage, VZ, can then be found from: V = VZTJ. VZ, the zener voltage temperature coefficient, is found from Figures 4 and 5. Under high power-pulse operation, the zener voltage will vary with time and may also be affected significantly by the zener resistance. For best regulation, keep current excursions as low as possible. Surge limitations are given in Figure 7. They are lower than would be expected by considering only junction temperature, as current crowding effects cause temperatures to be extremely high in small spots, resulting in device degradation should the limits of Figure 7 be exceeded. 100 70 50 20 10 7 5 2 1 0.7 0.5 +125C 0.2 0.1 0.07 0.05 0.02 0.01 0.007 0.005 +25C 0.002 0.001 3 4 5 6 7 8 9 10 11 12 13 VZ, NOMINAL ZENER VOLTAGE (VOLTS) Figure 3. Typical Leakage Current http://onsemi.com 4 14 15 BZX79C2V4RL Series TEMPERATURE COEFFICIENTS +12 VZ , TEMPERATURE COEFFICIENT (mV/ C) VZ , TEMPERATURE COEFFICIENT (mV/ C) (-55C to +150C temperature range; 90% of the units are in the ranges indicated.) +10 +8 +6 +4 +2 RANGE 0 VZ@IZT (NOTE 2) -2 -4 2 3 4 5 6 7 8 9 VZ, ZENER VOLTAGE (VOLTS) 10 11 12 100 70 50 30 20 3 2 1 10 200 180 160 140 100 VZ@IZT (NOTE 2) 120 130 140 150 160 170 180 190 20 200 +2 20mA 0 0.01mA 1mA NOTE: BELOW 3 VOLTS AND ABOVE 8 VOLTS NOTE: CHANGES IN ZENER CURRENT DO NOT NOTE: AFFECT TEMPERATURE COEFFICIENTS -2 -4 3 4 C, CAPACITANCE (pF) C, CAPACITANCE (pF) 100 70 50 200 1V BIAS 20 10 50% OF VZBIAS 5 7 8 TA=25C 0 BIAS 30 20 1VOLTBIAS 10 7 5 50% OF VZBIAS 3 2 2 1 6 Figure 5. Effect of Zener Current 0V BIAS 50 5 VZ, ZENER VOLTAGE (VOLTS) TA=25C 100 100 VZ@IZ TA=25C +4 Figure 4c. Range for Units 120 to 200 Volts 500 70 +6 VZ, ZENER VOLTAGE (VOLTS) 1000 30 50 VZ, ZENER VOLTAGE (VOLTS) Figure 4b. Range for Units 12 to 100 Volts VZ , TEMPERATURE COEFFICIENT (mV/ C) VZ , TEMPERATURE COEFFICIENT (mV/ C) Figure 4a. Range for Units to 12 Volts 120 VZ@IZ(NOTE 2) RANGE 10 7 5 1 2 5 10 20 50 1 100 120 VZ, ZENER VOLTAGE (VOLTS) 140 160 180 190 200 220 VZ, ZENER VOLTAGE (VOLTS) Figure 6a. Typical Capacitance 2.4-100 Volts Figure 6b. Typical Capacitance 120-200 Volts http://onsemi.com 5 Ppk , PEAK SURGE POWER (WATTS) BZX79C2V4RL Series 100 70 50 RECTANGULAR WAVEFORM TJ=25C PRIOR TO INITIAL PULSE 11V-91V NONREPETITIVE 5% DUTY CYCLE 30 1.8V-10V NONREPETITIVE 20 10 7 5 10% DUTY CYCLE 20% DUTY CYCLE 3 2 1 0.01 0.02 0.05 0.1 0.2 0.5 1 2 5 10 20 50 100 200 500 1000 PW, PULSE WIDTH (ms) Figure 7a. Maximum Surge Power 1.8-91 Volts Ppk , PEAK SURGE POWER (WATTS) RECTANGULAR WAVEFORM, TJ=25C ZZ , DYNAMIC IMPEDANCE (OHMS) 1000 500 1000 700 500 300 200 200 47V 100 100 70 50 30 20 100-200VOLTS NONREPETITIVE 10 7 5 3 2 1 0.01 0.1 1 10 100 27V 50 20 6.2V 10 5 2 1 1000 0.1 0.2 0.5 Figure 7b. Maximum Surge Power DO-204AH 100-200 Volts 5mA 20 20mA 1000 50 100 50 20 75C 10 25C 5 150C 0C 2 2 20 100 2 1 10 200 10 7 5 1 5 MAXIMUM MINIMUM 500 I F , FORWARD CURRENT (mA) ZZ , DYNAMIC IMPEDANCE (OHMS) 100 70 50 2 Figure 8. Effect of Zener Current on Zener Impedance TJ=25C iZ(rms)=0.1 IZ(dc) f=60Hz IZ=1mA 200 1 IZ, ZENER CURRENT (mA) PW, PULSE WIDTH (ms) 1000 700 500 TJ=25C iZ(rms)=0.1 IZ(dc) f=60Hz VZ=2.7V 3 5 7 10 20 30 50 70 100 1 0.4 VZ, ZENER VOLTAGE (VOLTS) 0.5 0.6 0.7 0.8 0.9 1 VF, FORWARD VOLTAGE (VOLTS) Figure 9. Effect of Zener Voltage on Zener Impedance http://onsemi.com 6 Figure 10. Typical Forward Characteristics 1.1 BZX79C2V4RL Series 20 10 I Z , ZENER CURRENT (mA) TA=25 1 0.1 0.01 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 29 30 VZ, ZENER VOLTAGE (VOLTS) Figure 11. Zener Voltage versus Zener Current -- VZ = 1 thru 16 Volts 10 I Z , ZENER CURRENT (mA) TA=25 1 0.1 0.01 15 16 17 18 19 20 21 22 23 24 25 26 27 28 VZ, ZENER VOLTAGE (VOLTS) Figure 12. Zener Voltage versus Zener Current -- VZ = 15 thru 30 Volts http://onsemi.com 7 BZX79C2V4RL Series I Z , ZENER CURRENT (mA) 10 TA=25 1 0.1 0.01 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 250 260 VZ, ZENER VOLTAGE (VOLTS) Figure 13. Zener Voltage versus Zener Current -- VZ = 30 thru 105 Volts I Z , ZENER CURRENT (mA) 10 1 0.1 0.01 110 120 130 140 150 160 170 180 190 200 210 220 230 240 VZ, ZENER VOLTAGE (VOLTS) Figure 14. Zener Voltage versus Zener Current -- VZ = 110 thru 220 Volts http://onsemi.com 8 BZX79C2V4RL Series OUTLINE DIMENSIONS Zener Voltage Regulators - Axial Leaded 500 mW DO-35 Glass GLASS DO-35/D0-204AH CASE 299-02 ISSUE A NOTES: 1. PACKAGE CONTOUR OPTIONAL WITHIN A AND B HEAT SLUGS, IF ANY, SHALL BE INCLUDED WITHIN THIS CYLINDER, BUT NOT SUBJECT TO THE MINIMUM LIMIT OF B. 2. LEAD DIAMETER NOT CONTROLLED IN ZONE F TO ALLOW FOR FLASH, LEAD FINISH BUILDUP AND MINOR IRREGULARITIES OTHER THAN HEAT SLUGS. 3. POLARITY DENOTED BY CATHODE BAND. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. B D K F A DIM A B D F K F K MILLIMETERS MIN MAX 3.05 5.08 1.52 2.29 0.46 0.56 --1.27 25.40 38.10 INCHES MIN MAX 0.120 0.200 0.060 0.090 0.018 0.022 --0.050 1.000 1.500 All JEDEC dimensions and notes apply. http://onsemi.com 9 BZX79C2V4RL Series Notes http://onsemi.com 10 BZX79C2V4RL Series Notes http://onsemi.com 11 BZX79C2V4RL Series ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (Mon-Fri 2:30pm to 7:00pm CET) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (Mon-Fri 2:00pm to 7:00pm CET) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (Mon-Fri 12:00pm to 5:00pm GMT) Email: ONlit@hibbertco.com CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com Toll-Free from Mexico: Dial 01-800-288-2872 for Access - then Dial 866-297-9322 ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 1-303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, UK, Ireland For additional information, please contact your local Sales Representative. http://onsemi.com 12 BZX79C2V4RL/D