Freescale Semiconductor Technical Data MRFIC1505 Rev. 1, 08/2004 MRFIC1505/MRFIC1505A Integrated GPS Downconverter 1.575 GHz GPS DOWNCONVERTER This integrated circuit is intended for GPS receiver applications. The dual conversion design is implemented in Motorola's low-cost, high-performance MOSAIC 5. silicon bipolar process and is packaged in a low-cost surface mount LQFP-48 package. In addition to the mixers, a VCO, PLL, Crystal Oscillator, A/D converter and a loop filter are integrated on-chip. Output IF is nominally 4.1 MHz. * 105 dB Typical Conversion Gain * 2.7 V Operation * 28 mA Typical Current Consumption * Low-Cost, Low-Profile Plastic LQFP Package MOSAIC 5 is a trademark of Motorola, Inc. Ordering Information Operating Temperature Range Package MRFIC1505R2 TA = -40 to 85C LQFP-48 MRFIC1505AR2 TA = -40 to 85C LQFP-48 Device (c) Freescale Semiconductor, Inc., 2004. All rights reserved. Plastic Package Case 932 (LQFP-48) Maximum Ratings Symbol Value Unit DC Supply Voltage Rating VDD 5.0 Vdc DC Supply Current IDD 60 mA Operating Ambient Temperature TA -40 to 85 C Tstg -65 to 150 C - 260 C Storage Temperature Range Lead Soldering Temperature Range Note: Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the limits in the Electrical Characteristics tables. Electrical Characteristics (VCC = 2.7 to 3.3 V; TA = -40 to 85C; Enable = 2.7 V unless otherwise noted) Characteristic Total Device Supply Voltage Supply Current (TA = 25C, VCC = 2.7 V, Enable = 2.7V) Supply Current (TA = 25C, VCC = 2.7 V, Enable = 2.7V) RF Amplifier RF Input Frequency Input Impedance Input VSWR Gain Noise Figure 1.0 dB Compression (Measured at Output) First Mixer Input Frequency Gain Noise Figure 1.0 dB compression (Measured at Output) First Local Oscillator Frequency First Intermediate Frequenc LO Leakage at IF Port LO Leakage at RF Port Output Impedance First IF Amplifier and Second Mixer Input Frequency Input Impedance Output Impedance Second Local Oscillator Frequency Second Intermediate Frequency LO Leakage at IF Port Gain Cascaded Noise Figure 1.0 dB Compression Point (Measured at Output) Limiting Amplifier Second Intermediate Frequency Input Signal Level Output Voltage Swing (into 10 pf ll100 k DC Output Level Gain Reference Oscillator Reference Frequency Reference Frequency Input Level (Crystal Output Pin) 2 Symbol Min Typ Max Unit VCC 2.7 3.0 3.3 V ICC - 28 36 mA ICC - 2.0 4.0 mA fin Zin VSWRin G NF P1dB - - - 13 - - 1575.42 50 2.0 15 2.0 1.0 - - - - - - MHz - dB dB dBm fin G NF P1dB fLO1 fIF1 - - Zout - 10 - - - - - - - 1575.42 14 13 -13 1636.8 61.38 -40 -50 50 - - - - - - - - - MHz dB dB dBm MHz MHz dBm dBm fin Zin Zout fLO2 fIF2 - G NF P1dB - - - - - - 40 - - 61.38 230 50 65.47 4.092 -40 43 9.3 -13 - - - - - - - - - MHz MHz MHz dBm dB dB dBm fIF2 - Vout - G - 4.0 800 - - 4.092 11 - 1.4 50 - 31 - - - MHz Mv mVpp V dB fr - - - 16.368 500 - - MHz mVpp Freescale Semiconductor Electrical Characteristics (VCC = 2.7 to 3.3 V; TA = -40 to 85C; Enable = 2.7 V unless otherwise noted) Characteristic Reference Oscillator Output Voltage Level (Into 15 pf II 10 k) Reference Clock Input Drive Level PLL First Local Oscillator Frequency Second Local Oscillator Frequency VCO C/N (at 10 kHz Offset) VCO Gain (TBD Varactor) Enable Enable Active Level Disable Active Level Voltage Regulator Regulator Output Voltage (VCC = 2.7 to 3.3 V, Iout = 3.0 mA) MRFIC505 Temperature Sense Specs Temperature Sensor Output Voltage @ 25C Temperature Sensor Slope over Temperature MRFIC505A Temperature Sense Specs Temperature Sensor Output Voltage @ 25C Temperature Sensor Slope over Temperature Freescale Semiconductor Symbol - - Min 750 400 Typ - 800 Max - 1500 Unit mVpp mVpp fLO1 fLO2 - - - - - - 1636.8 65.47 -80 200 - - - - MHz MHz dBc/Hz MHz/V - - 0.8 x VCC - VCC 0 - 0.2 x VCC V V VO 2.1 2.3 2.5 V - - 1.2 - 1.28 5.0 1.375 - V mV/C - - 1.270 - 1.395 5.0 1.463 - V mV/C 3 Figure 1 Applications Schematic (1636.8 MHz LO) 4 Freescale Semiconductor Outline Dimensions PLASTIC PACKAGE CASE 932-03 (LQFP-48) ISSUE F 4X NOTES: 1 DIMENSIONING AND TOLERANCING PER ASME 2 DATUM 3 CONTROLLING Y14.5M,PLANE 1994.AB DIMENSION: IS LOCATED MILLIMETER. AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT 4 DATUMS THE BOTTOM T, U, AND OF THE Z TOPARTING BE DETERMINED LINE. AT 5 DIMENSIONS DATUM PLANE S AND AB. V TO BE DETERMINED AT 6 DIMENSIONS SEATING PLANE A AND AC.B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.250 PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE 7 DIMENSION DETERMINED D DOES AT DATUM NOTPLANE INCLUDE AB.DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 8 MINIMUM 0.350. SOLDER PLATE THICKNESS SHALL BE 9 EXACT 0.0076. SHAPE OF EACH CORNER IS OPTIONAL. 0.200 AB T-U Z 9 DETAIL Y A P A1 48 37 1 36 T U V B AE B1 12 25 13 AE V1 24 DIM A A1 B B1 C D E F G H J K L M N P R S S1 V V1 W AA Z S1 T, U, Z S DETAIL Y 4X 0.200 AC T-U Z 0.080 AC G AB AD AC MILLIMETERS MIN MAX 7.000 BSC 3.500 BSC 7.000 BSC 3.500 BSC 1.400 1.600 0.170 0.270 1.350 1.450 0.170 0.230 0.500 BSC 0.050 0.150 0.090 0.200 0.500 0.700 0 _ 7 _ 12 _ REF 0.090 0.160 0.250 BSC 0.150 0.250 9.000 BSC 4.500 BSC 9.000 BSC 4.500 BSC 0.200 REF 1.000 REF M _ BASE METAL TOP & BOTTOM 0.250 J C E GAUGE PLANE N R F D 0.080 M AC T-U Z SECTION AE-AE W H L _ K DETAIL AD AA Freescale Semiconductor 5 NOTES 6 Freescale Semiconductor NOTES Freescale Semiconductor 7 How to Reach Us: Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Technical Information Center 3-20-1, Minami-Azabu, Minato-ku Tokyo 106-0047, Japan 0120 191014 or +81 3 3440 3569 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2004. All rights reserved. MRFIC1505 Rev. 1 08/2004