SEMICONDUCTOR
TECHNICAL DATA
QUAD DIFFERENTIAL INPUT
OPERATIONAL AMPLIFIERS
ORDERING INFORMATION
PIN CONNECTIONS
Order this document by LM324/D
D SUFFIX
PLASTIC PACKAGE
CASE 751A
(SO–14)
N SUFFIX
PLASTIC PACKAGE
CASE 646
(LM224, LM324,
LM2902 Only)
14
1
14 1
8
Out 4
Inputs 4
VEE, Gnd
Inputs 3
Out 3
9
10
11
12
13
14
2
Out 1
VCC
Out 2
1
3
4
5
6
7
*
)
Inputs 1
Inputs 2
(Top View)
4
23
1
)
*
*
)
)
*
LM224N
Device Operating
Temperature Range Package
LM2902VD
LM2902VN
LM224D
LM324AD
LM324AN
LM324D
LM324N
TA = –40° to +125°C
TA = –25° to +85°C
TA = 0° to +70°C
Plastic DIP
Plastic DIP
SO–14
SO–14
SO–14
SO–14
Plastic DIP
Plastic DIP
LM2902D
LM2902N TA = –40° to +105°CSO–14
Plastic DIP
1
MOTOROLA ANALOG IC DEVICE DATA
The LM324 series are low–cost, quad operational amplifiers with true
differential inputs. They have several distinct advantages over standard
operational amplifier types in single supply applications. The quad amplifier
can operate at supply voltages as low as 3.0 V or as high as 32 V with
quiescent currents about one–fifth of those associated with the MC1741 (on
a per amplifier basis). The common mode input range includes the negative
supply, thereby eliminating the necessity for external biasing components in
many applications. The output voltage range also includes the negative
power supply voltage.
•Short Circuited Protected Outputs
•T rue Dif ferential Input Stage
•Single Supply Operation: 3.0 V to 32 V
•Low Input Bias Currents: 100 nA Maximum (LM324A)
•Four Amplifiers Per Package
•Internally Compensated
•Common Mode Range Extends to Negative Supply
•Industry Standard Pinouts
•ESD Clamps on the Inputs Increase Ruggedness without Affecting
Device Operation
MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.)
Rating Symbol LM224
LM324, LM324A LM2902,
LM2902V Unit
Power Supply Voltages Vdc
Single Supply VCC 32 26
Split Supplies VCC, VEE ±16 ±13
Input Differential
Voltage Range (See
Note 1)
VIDR ±32 ±26 Vdc
Input Common Mode
V oltage Range VICR –0.3 to 32 –0.3 to 26 Vdc
Output Short Circuit
Duration tSC Continuous
Junction Temperature TJ150 °C
Storage Temperature
Range Tstg –65 to +150 °C
Operating Ambient
Temperature Range TA–25 to +85
0 to +70 –40 to +105
–40 to +125 °C
NOTE: 1. Split Power Supplies.
Motorola, Inc. 1996 Rev 3
LM324, LM324A, LM224, LM2902, LM2902V
2MOTOROLA ANALOG IC DEVICE DATA
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.)
LM224 LM324A LM324 LM2902 LM2902V
Characteristics Symbol Min Typ Max Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit
Input Of fset Voltage V IO mV
VCC = 5.0 V to 30 V
(26 V for LM2902,
V), VICR = 0 V to
VCC –1.7 V, VO =
1.4 V, RS = 0 Ω
TA = 25°C– 2.0 5.0 – 2.0 3.0 – 2.0 7.0 – 2.0 7.0 – 2.0 7.0
TA = Thigh(1) – – 7.0 – – 5.0 – – 9.0 – – 10 – – 13
TA = Tlow(1) – – 7.0 – – 5.0 – – 9.0 – – 10 – – 10
Average Temperature
Coefficient of Input
Offset Voltage
∆VIO/∆T – 7.0 – – 7.0 30 – 7.0 – – 7.0 – – 7.0 – µV/°C
TA = Thigh to Tlow(1)
Input Offset Current IIO –3.0 30 – 5.0 30 – 5.0 50 – 5.0 50 – 5.0 50 nA
TA = Thigh to Tlow(1) – – 100 – – 75 – – 150 – – 200 – – 200
Average Temperature
Coefficient of Input
Offset Current
∆IIO/∆T – 10 – – 10 300 – 10 – – 10 – – 10 – pA/°C
TA = Thigh to Tlow(1)
Input Bias Current IIB ––90 –150 – –45 –100 – –90 –250 – –90 –250 – –90 –250 nA
TA = Thigh to Tlow(1) – – –300 – – –200 – – –500 – – –500 – – –500
Input Common Mode
V oltage Range(2) VICR V
VCC = 30 V (26 V for
LM2902, V) 0 – 28.3 0 – 28.3 0 – 28.3 0 – 24.3 0 – 24.3
VCC = 30 V (26 V for
LM2902, V),
TA = Thigh to Tlow
0 – 28 0 – 28 0 – 28 0 – 24 0 – 24
Differential Input
V oltage Range VIDR – – VCC – – VCC – – VCC – – VCC – – VCC V
Large Signal Open
Loop V oltage Gain AVOL V/mV
RL = 2.0 kΩ, VCC =
15 V, for Large VO
Swing, TA = Thigh
to Tlow(1)
50
25 100
––
–25
15 100
––
–25
15 100
––
–25
15 100
––
–25
15 100
––
–
Channel Separation
10 kHz ≤ f ≤ 20 kHz,
Input Referenced
CS – –120 – – –120 – – –120 – – –120 – – –120 – dB
Common Mode
Rejection, RS ≤ 10 kΩCMR 70 85 – 65 70 – 65 70 – 50 70 – 50 70 – dB
Power Supply
Rejection PSR 65 100 – 65 100 – 65 100 – 50 100 – 50 100 – dB
Output V oltage–High
Limit (TA = Thigh to
Tlow)(1)
VOH V
VCC = 5.0 V, RL =
2.0 kΩ, TA = 25°C3.3 3.5 – 3.3 3.5 – 3.3 3.5 – 3.3 3.5 – 3.3 3.5 –
VCC = 30 V (26 V for
LM2902, V),
RL = 2.0 kΩ
26 – – 26 – – 26 – – 22 – – 22 – –
VCC = 30 V (26 V for
LM2902, V),
RL = 10 kΩ
27 28 – 27 28 – 27 28 – 23 24 – 23 24 –
NOTES: 1.Tlow = –25°C for LM224 Thigh = +85°C for LM224
=0°C for LM324, A = +70°C for LM324, A
= –40°C for LM2902 = +105 °C for LM2902
= –40°C for LM2902V = +125°C for LM2902V
2.The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the
common mode voltage range is VCC –1.7 V.
LM324, LM324A, LM224, LM2902, LM2902V
3
MOTOROLA ANALOG IC DEVICE DATA
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.)
LM224 LM324A LM324 LM2902 LM2902V
Characteristics Symbol Min Typ Max Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit
Output V oltage – Low
Limit, VCC = 5.0 V, RL
= 10 kΩ, TA = Thigh to
Tlow(1)
VOL – 5.0 20 – 5.0 20 – 5.0 20 – 5.0 100 – 5.0 100 mV
Output Source Current
(VID = +1.0 V, VCC =
15 V)
IO +mA
TA = 25°C20 40 – 20 40 – 20 40 – 20 40 – 20 40 –
TA = Thigh to Tlow(1) 10 20 – 10 20 – 10 20 – 10 20 – 10 20 –
Output Sink Current IO –mA
(VID = –1.0 V, VCC =
15 V) TA = 25°C10 20 – 10 20 – 10 20 – 10 20 – 10 20 –
TA = Thigh to Tlow(1) 5.0 8.0 – 5.0 8.0 – 5.0 8.0 – 5.0 8.0 – 5.0 8.0 –
(VID = –1 .0 V, VO =
200 mV, TA = 25°C) 12 50 – 12 50 – 12 50 – – – – – – – µA
Output Short Circuit to
Ground(3) ISC –40 60 – 40 60 – 40 60 – 40 60 – 40 60 mA
Power Supply Current
(TA = Thigh to Tlow)(1) ICC mA
VCC = 30 V (26 V for
LM2902, V),
VO = 0 V, RL = ∞
– – 3.0 – 1.4 3.0 – – 3.0 – – 3.0 – – 3.0
VCC = 5.0 V,
VO = 0 V, RL = ∞– – 1.2 – 0.7 1.2 – – 1.2 – – 1.2 – – 1.2
NOTES: 1.Tlow = –25°C for LM224 Thigh = +85°C for LM224
=0°C for LM324, A = +70°C for LM324, A
= –40°C for LM2902 = +105 °C for LM2902
= –40°C for LM2902V = +125°C for LM2902V
2.The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the
common mode voltage range is VCC –1.7 V.
Representative Circuit Diagram
(One–Fourth of Circuit Shown)
Output
Bias Circuitry
Common to Four
Amplifiers
VCC
VEE/Gnd
Inputs
Q2
Q3 Q4
Q5
Q26
Q7
Q8
Q6
Q9 Q11
Q10 Q1 2.4 k
Q25
Q22
40 k
Q13
Q14
Q15
Q16
Q19
5.0 pF
Q18
Q17
Q20
Q21
2.0 k
Q24
Q23
Q12
25
+
–
LM324, LM324A, LM224, LM2902, LM2902V
4MOTOROLA ANALOG IC DEVICE DATA
CIRCUIT DESCRIPTION
The LM324 series is made using four internally
compensated, two–stage operational amplifiers. The first
stage of each consists of differential input devices Q20 and
Q18 with input buffer transistors Q21 and Q17 and the
differential to single ended converter Q3 and Q4. The first
stage performs not only the first stage gain function but also
performs the level shifting and transconductance reduction
functions. By reducing the transconductance, a smaller
compensation capacitor (only 5.0 pF) can be employed, thus
saving chip area. The transconductance reduction is
accomplished by splitting the collectors of Q20 and Q18.
Another feature of this input stage is that the input common
mode range can include the negative supply or ground, in
single supply operation, without saturating either the input
devices or the differential to single–ended converter. The
second stage consists of a standard current source load
amplifier stage.
Large Signal Voltage Follower Response
VCC = 15 Vdc
RL = 2.0 k
Ω
TA = 25
°
C
5.0
µ
s/DIV
1.0 V/DIV
Each amplifier is biased from an internal–voltage regulator
which has a low temperature coefficient thus giving each
amplifier good temperature characteristics as well as
excellent power supply rejection.
Single Supply Split Supplies
VCC
VEE/Gnd
3.0 V to VCC(max)
1
2
3
4
VCC
1
2
3
4
VEE
1.5 V to VCC(max)
1.5 V to VEE(max)
LM324, LM324A, LM224, LM2902, LM2902V
5
MOTOROLA ANALOG IC DEVICE DATA
VOR, OUTPUT VOLT AGE RANGE (V )
pp
VO, OUTPUT VOLT AGE (mV)
14
12
10
8.0
6.0
4.0
2.0
01.0 10 100 1000
f, FREQUENCY (kHz)
550
500
450
400
350
300
250
200
00 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
t, TIME (
µ
s)
2.4
2.1
1.8
1.5
1.2
0.9
0.6
0.3
00 5.0 10 15 20 25 30 35
VCC, POWER SUPPLY VOLTAGE (V) VCC, POWER SUPPLY VOLTAGE (V)
90
80
70 0 2.0 4.0 6.0 8.0 10 12 14 16 18 20
I , POWER SUPPLY CURRENT (mA)
CC
I , INPUT BIAS CURRENT (nA)
IB
VCC = 30 V
VEE = Gnd
TA = 25
°
C
CL = 50 pF
Input
Output
V , INPUT VOLTAGE (V)
I
Figure 1. Input Voltage Range Figure 2. Open Loop Frequency
18
16
14
12
10
8.0
6.0
4.0
2.0
0
20
0 2.0 4.0 6.0 8.0 10 12 14 16 18 20
±
VCC/VEE, POWER SUPPLY VOLTAGES (V)
120
100
80
60
40
20
0
–201.0 10 100 1.0 k 10 k 100 k 1.0 M
f, FREQUENCY (Hz)
±
A , LARGE–SIGNAL
VOL
OPEN LOOP VOLTAGE GAIN (dB)
Positive
Negative
VCC = 15 V
VEE = Gnd
TA = 25
°
C
TA = 25
°
C
RL =
R
RL = 2.0 k
Ω
VCC = 15 V
VEE = Gnd
Gain = –100
RI = 1.0 k
Ω
RF = 100 k
Ω
Figure 3. Large–Signal Frequency Response Figure 4. Small–Signal Voltage Follower
Pulse Response (Noninverting)
Figure 5. Power Supply Current versus
Power Supply Voltage Figure 6. Input Bias Current versus
Power Supply Voltage
LM324, LM324A, LM224, LM2902, LM2902V
6MOTOROLA ANALOG IC DEVICE DATA
2
1
R1
TBP
R1 + R2
R1
R1 + R2
eo
e1
e2
eo = C (1 + a + b) (e2 – e1)
R1 a R1
b R1
R
–
+
+
–
–
+R
+
–
R1
R2
VO
Vref
Vin
VOH
VO
VOL
VinL = R1 (VOL – Vref) + Vref
VinH = (VOH – Vref) + Vref
H = R1 + R2 (VOH – VOL)
R1
–
+
–
+
–
+
R
C
R2 R1 R3
C1
100 k
R
C
R
C1 R2
100 k
Vin
V ref
V ref Vref
V ref
Bandpass
Output
fo = 2
π
RC
R1 = QR
R2 =
R3 = TN R2
C1 = 10C
1
Notch Output
Vref =V
CC
Hysteresis
1
CR
VinL VinH
Vref
Where: TBP = Center Frequency Gain
Where: TN= Passband Notch Gain
R = 160 k
Ω
C = 0.001
µ
F
R1 = 1.6 M
Ω
R2 = 1.6 M
Ω
R3 = 1.6 M
Ω
For: fo= 1.0 kHz
For: Q= 10
For: TBP = 1
For: TN= 1
–
+
MC1403
1/4
LM324
–
+
R1
VCC VCC
VO
2.5 V
R2
50 k
10 k
Vref
Vref = VCC
2
5.0 k
RCRC
+
–VO
2
π
RC
1
For: fo = 1.0 kHz
R = 16 k
Ω
C = 0.01
µ
F
VO = 2.5 V 1 + R1
R2
1
VCC
fo =
1/4
LM324
1/4
LM324
1/4
LM324
1/4
LM324
1
CR
1/4
LM324
1/4
LM324 1/4
LM324 1/4
LM324
1/4
LM324
Figure 7. Voltage Reference Figure 8. Wien Bridge Oscillator
Figure 9. High Impedance Differential Amplifier Figure 10. Comparator with Hysteresis
Figure 11. Bi–Quad Filter
LM324, LM324A, LM224, LM2902, LM2902V
7
MOTOROLA ANALOG IC DEVICE DATA
2
1
Vref =V
CC
1
2
For less than 10% error from operational amplifier,
If source impedance varies, filter may be preceded with
voltage follower buffer to stabilize filter parameters.
where fo and BW are expressed in Hz.
Qo fo
BW < 0.1
Given: fo= center frequency
A(fo) = gain at center frequency
Choose value fo, C
Then: R3 = Q
π
fo C
R3
R1 = 2 A(fo)
R1 R3
4Q2 R1 – R3
R2 =
+
–+
–
–
+
Vref =V
CC
Vref
f = R1 + RC
4 CRf R1 R3 = R2 R1
R2 + R1
R2
300 k
75 k
R3
R1
100 k
C
T riangle Wave
Output
Square
Wave
Output
VCC
R3
R1
R2
Vref
Vin
CC
VO
CO = 10 C
Rf
if
Vref
CO
1/4
LM324
1/4
LM324 1/4
LM324
Figure 12. Function Generator Figure 13. Multiple Feedback Bandpass Filter
LM324, LM324A, LM224, LM2902, LM2902V
8MOTOROLA ANALOG IC DEVICE DATA
OUTLINE DIMENSIONS
NOTES:
1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE
POSITION AT SEATING PLANE AT MAXIMUM
MATERIAL CONDITION.
2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
3. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.
4. ROUNDED CORNERS OPTIONAL.
17
14 8
B
A
F
HG D K
C
N
L
J
M
SEATING
PLANE
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.715 0.770 18.16 19.56
B0.240 0.260 6.10 6.60
C0.145 0.185 3.69 4.69
D0.015 0.021 0.38 0.53
F0.040 0.070 1.02 1.78
G0.100 BSC 2.54 BSC
H0.052 0.095 1.32 2.41
J0.008 0.015 0.20 0.38
K0.115 0.135 2.92 3.43
L0.300 BSC 7.62 BSC
M0 10 0 10
N0.015 0.039 0.39 1.01
____
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
–A–
–B–
G
P7 PL
14 8
71 M
0.25 (0.010) B M
S
B
M
0.25 (0.010) A S
T
–T–
F
RX 45
SEATING
PLANE
D14 PL K
C
J
M
_
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A8.55 8.75 0.337 0.344
B3.80 4.00 0.150 0.157
C1.35 1.75 0.054 0.068
D0.35 0.49 0.014 0.019
F0.40 1.25 0.016 0.049
G1.27 BSC 0.050 BSC
J0.19 0.25 0.008 0.009
K0.10 0.25 0.004 0.009
M0 7 0 7
P5.80 6.20 0.228 0.244
R0.25 0.50 0.010 0.019
____
D SUFFIX
PLASTIC PACKAGE
CASE 751A–03
(SO–14)
ISSUE F
N SUFFIX
PLASTIC PACKAGE
CASE 646–06
(LM224, LM324, LM2902 Only)
ISSUE L
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Af firmative Action Employer .
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center ,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: RMF AX0@email.sps.mot.com – TOUCHT ONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
LM324/D
*LM324/D*
◊
