H3M-AC200/220/240-A - Omron

CSM_H3M_DS_E_2_1

Solid-state Timer

H3M

Solid-state Timer with Variable Time Ranges

• Four time ranges are selectable per timer unit.

• Wide timing range of 0.05 second to 30 hours can be covered

by a combination of five timer units.

• Standard surface mounting type is easily convertible to flush

mounting type with the use of a special adapter (Y92F-40).

• Requires only 40 x 50 mm for mounting space.

• Equipped with power-ON & time-out indicators.

• All standard models approved by UL, CSA, and LR.

Ordering Information

Note: 1. Specify both the model number and supply voltage when ordering.

2. Sockets and adapters for surface/track mounting are available optionally and therefore, place the order for them as necessary.

Timer hold-down clips (F-hook and L-hook) are supplied with the timer.

■Accessories (Order Separately)

Adapter

Y92F-40

Specifications

■Time Ranges

Four time ranges are available for each timer by changing the time range selector switch positions to different combinations.

Operation/resetting system Time-limit contact Instantaneous

contact

Mounting

Surface mounting Flush mounting

Time-limit operation/ self-resetting DPDT --- H3M H3M with Y92F-40 adapter

SPDT SPDT H3M-H H3M-H with Y92F-40 adapter

Time range code Time range selector switch

A0.05 to 0.5 s 0.5 to 5 s 0.05 to 0.5 min 0.5 to 5 min

B0.1 to 1 s 1 to 10 s 0.1 to 1 min 1 to 10 min

C0.3 to 3 s 3 to 30 s 0.3 to 3 min 3 to 30 min

Time range code Time multiplying key

D0.1 to 1 min 1 to 10 min 0.1 to 1 hrs 1 to 10 hrs

E0.3 to 3 min 3 to 30 min 0.3 to 3 hrs 3 to 30 hrs

H3M

■Ratings

Note: 1. Color indicators for the rated voltage are provided on the front of the Timer.

Blue: 100/110/120 VAC

Red: 200/220/240 VAC

None: Other voltages

2. With DC ratings, single-phase full-wave rectified power sources may be used.

3. 90% to 110% for 12-VDC models.

■Characteristics

Note: For the timer with time range code A, add ±10 ms to the respective characteristics when the time range selector switches are in the x 1 s

(0.05 to 0.5 s) position.

Rated supply voltage 100/110/120 VAC (50/60 Hz), 200/220/240 VAC (50/60 Hz),

12, 24, 48, 100, 110 VDC (see note 2)

Operating voltage range AC: 85% to 110% of rated supply voltage

DC: 80% to 110% of rated supply voltage (see note 3)

Power consumption AC: Approx. 5 VA/2 W

DC: Approx. 2 W

Control outputs 5 A at 250 VAC, resistive load (cosφ = 1)

Accuracy of operating time ±1% max. (see note)

Setting error ±10% max.

Reset time 0.1 s max.

Influence of voltage ±1% max. (see note)

Influence of temperature ±2% max. (see note)

Insulation resistance 100 MΩ min. (at 500 VDC)

Dielectric strength 2,000 VAC, 50/60 Hz for 1 min (between current-carrying and non-current-carrying parts)

1,500 VAC, 50/60 Hz for 1 min (between contact and control circuit)

1,000 VAC, 50/60 Hz for 1 min (between non-continuous contacts)

Vibration resistance Destruction: 10 to 55 Hz with 0.75-mm double amplitude

Malfunction: 10 to 55 Hz with 0.5-mm double amplitude

Shock resistance Destruction: 1,000 m/s2 (approx. 100G)

Malfunction: 100 m/s2 (approx. 10G)

Ambient temperature Operating: –10°C to 50°C

Storage: –25°C to 65°C

Ambient humidity Operating: 35% to 85%

Life expectancy Mechanical: 20,000,000 operations min. (under no load at 1,800 operations/h)

Electrical: 100,000 operations min. (5 A at 250 VAC, resistive load at 1,800 operations/h)

Approved standards UL (File No. E41515), CSA (File No. LR22310)

Weight Approx. 100 g

H3M

Engineering Data

Operation

■Timing Chart

Switching operations (×103)

Load current (A)

Reference: A maximum current of 0.15 A can be switched at 125 VDC (cosφ = 1).

Maximum current of 0.1 A can be switched if L/R is 7 ms. In both cases,

a life of 100,000 operations can be expected.The minimum applicable

load is 10 mA at 5 VDC (failure level: P).

H3M H3M-H

Set time Set time Set time Set time

Rt Rt

Rt: Resetting time Rt: Resetting time

7-2 (Power)

1-4 (NC)

1-3 (NO)

8-5 (NC)

8-6 (NO)

2-7 (Power)

8-5 (NC)

8-6 (NO)

1-4 (NC)

1-3 (NO)

Power ON

indicator lamp

Time-out

indicator

Power ON

indicator lamp

Time-out

indicator

H3M

Dimensions

Note: All units are in millimeters unless otherwise indicated.

■Accessories (Order Separately)

H3M(-H)

Y92F-40 Adapter with Flush Mounting

Track Mounted/Front Connecting Socket

PF085A

Terminal Arrangement

(Top View)

Mounting Holes

Eight, M3.5 × 7 sems

Four, 5 dia. or M4 holes

Note: When two or more timers mounted in line are to be continuously energized at the same time after the lapse

of the set time, be sure to limit the carry current to less than 1 A. When using the timers at an ambient

temperature of more than 40°C, be sure to reset the timers immediately after the set time has elapsed.

Mounting Height of

Timer with Socket

Note: PF085A can be used as a

front connecting socket.

Two, 4.5 dia.

holes

63.5

75.5

Hold-down Clips (Attached)

PHC-1 For PF085A

F-hook

H3M

P3G-08

Terminal Arrangement

(Bottom View)

Terminal Arrangement

(Bottom View)

Mounting Holes

Back Connecting Socket

PL08

Mounting Track

PFP-100N/PFP-50N

End Plate

PFP-M

Note: This dimension applies to PFP-50N.

Spacer

PFP-S

(See note)

Two, 2 dia.

holes

Mounting Height of

Timer with Socket

Mounting Height of

Timer with Socket

Two, 3.5 dia. or M3

socket mounting

holes

H3M

Installation

■Connection

Safety Precautions

Refer to Safety Precautions for All Timers.

Power Source Connection

Because the AC-operated version is a capacitive load, the solid-state

relay to be used must be rated at a dielectric strength two times as

that of the timer to switch the power source of the timer.

The H3M contains a capacitor-drop power circuit. Use a sinusoidal

power supply with a commercial frequency. Do not use power

supplies with a high frequency component (such as inverter power

supplies) for Timers with 100 to 240-VAC specifications. Using these

power supplies can damage internal circuits.

How to Change the Time Range

The H3M is provided with two time range selector switches. One is

on the lower right side A of the front panel and the other on the lower

left side. Change the positional combination of the time range

selector switches with a flat-blade screwdriver as desired.

!CAUTION

Be sure to turn the power off before changing the time specification.

Changing the time range while the timer is in operation may result in

a malfunction.

Connections

Connecting the Operating Power Supply

If using an AC power supply, connect it between terminals 2 and 7. If

using a DC power supply, connect the positive line to terminal 7 and

the negative line to terminal 2. An AC power supply can be

connected without considering polarity, but the DC power supply

lines must be connected as specified.

Other Precautions

•A DC power supply must have 50% or less ripple and the average

voltage must be within the rated supply voltage specification.

•A P3G-08 Socket can be used instead of a US-08 Socket to reduce

the depth. Also, the P3G-08 has screw terminals, making

maintenance easier.

H3M H3M-H

US-08 P3G-08

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Read and Understand This Catalog

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or

comments.

Warranty and Limitations of Liability

WARRANTY

OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)

from date of sale by OMRON.

OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR

FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS

DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED.

LIMITATIONS OF LIABILITY

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS

IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT

LIABILITY.

In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS

OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT

SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

Application Considerations

SUITABILITY FOR USE

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's

application or use of the products.

At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the

products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,

machine, system, or other application or use.

The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible

uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:

•

Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.

•

Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,

safety equipment, and installations subject to separate industry or government regulations.

•

Systems, machines, and equipment that could present a risk to life or property.

Please know and observe all prohibitions of use applicable to the products.

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE

SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND

INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

PROGRAMMABLE PRODUCTS

OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.

Disclaimers

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time based on improvements and other reasons.

It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.

However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or

establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual

specifications of purchased products.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

PERFORMANCE DATA

Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the

result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON

Warranty and Limitations of Liability.

ERRORS AND OMISSIONS

The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,

typographical, or proofreading errors, or omissions.

2008.11

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/