P6KE6.8 thru P6KE540A
Vishay General Semiconductor
Document Number: 88369
Revision: 22-Oct-08
For technical questions within your region, please contact one of the following:
PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com
www.vishay.com
1
TRANSZORB® Transient Voltage Suppressors
FEATURES
• Glass passivated chip junction
• Available in uni-directional and bi-directional
• 600 W peak pulse power capability with a
10/1000 µs waveform, repetitive rate (duty
cycle): 0.01 %
• Excellent clamping capability
• Very fast response time
• Low incremental surge resistance
• Solder dip 260 °C, 40 s
• Component in accordance to RoHS 2002/95/EC
and WEEE 2002/96/EC
TYPICAL APPLICATIONS
Use in sensitive electronics protection against voltage
transients induced by inductive load switching and
lighting on ICs, MOSFET, signal lines of sensor units
for consumer, computer, industrial, automotive and
telecommunication.
MECHANICAL DATA
Case: DO-204AC, molded epoxy over passivated chip
Molding compound meets UL 94 V-0 flammability
rating
Base P/N-E3 - RoHS compliant, commercial grade
Base P/NHE3 - RoHS compliant, high reliability/
automotive grade (AEC Q101 qualified)
Terminals: Matte tin plated leads, solderable per
J-STD-002 and JESD22-B102
E3 suffix meets JESD 201 class 1A whisker test, HE3
suffix meets JESD 201 class 2 whisker test
Note:
• P6KE250 ~ P6KE540A and P6KE250C ~ P6KE440CA for
commercial grade only
Polarity: For uni-directional types the color band
denotes cathode end, no marking on bi-directional
types
DEVICES FOR BI-DIRECTION APPLICATIONS
For bi-directional types, use C or CA suffix
(e.g. P6KE440CA).
Electrical characteristics apply in both directions.
PRIMARY CHARACTERISTICS
VBR uni-directional 6.8 V to 540 V
VBR bi-directional 6.8 V to 440 V
PPPM 600 W
PD5.0 W
IFSM (uni-directional only) 100 A
TJ max. 175 °C
DO-204AC (DO-15)
Notes:
(1) Non-repetitive current pulse, per Fig. 3 and derated above TA = 25 °C per Fig. 2
(2) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 per minute maximum
(3) VF = 3.5 V for P6KE220(A) and below; VF = 5.0 V for P6KE250(A) and above
MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)
PARAMETER SYMBOL VALUE UNIT
Peak power dissipation with a 10/1000 µs waveform (1) (Fig. 1) PPPM 600 W
Peak pulse current with a 10/1000 µs waveform (1) IPPM See next table A
Power dissipation on infinite heatsink at TL = 75 °C (Fig. 5) PD 5.0 W
Peak forward surge current, 8.3 ms single half sine-wave (2) IFSM 100 A
Maximum instantaneous forward voltage at 50 A for uni-directional only (3) VF 3.5/5.0 V
Operating junction and storage temperature range TJ, TSTG - 55 to + 175 °C
P6KE6.8 thru P6KE540A
Vishay General Semiconductor
www.vishay.com For technical questions within your region, please contact one of the following:
PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com
Document Number: 88369
Revision: 22-Oct-08
2
ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
DEVICE TYPE
BREAKDOWN
VOLTAG E
VBR AT IT (1)
(V)
TEST
CURRENT
IT
(mA)
STAND-OFF
VOLTAGE VWM
(V)
MAXIMUM
REVERSE
LEAKAGE
AT VWM (3) ID
(µA)
PEAK
PULSE
CURRENT
IPPM (2) (A)
MAXIMUM
CLAMPING
VOLTAGE AT
IPPM VC (V)
MAXIMUM
TEMPERATURE
COEFFICIENT
OF VBR (%/°C)
MIN. MAX.
(+)P6KE6.8 6.12 7.48 10 5.50 1000 55.6 10.8 0.057
(+)P6KE6.8A 6.45 7.14 10 5.80 1000 57.1 10.5 0.057
(+)P6KE7.5 6.75 8.25 10 6.05 500 51.3 11.7 0.061
(+)P6KE7.5A 7.13 7.88 10 6.40 500 53.1 11.3 0.061
(+)P6KE8.2 7.38 9.02 10 6.63 200 48.0 12.5 0.065
(+)P6KE8.2A 7.79 8.61 10 7.02 200 49.6 12.1 0.065
(+)P6KE9.1 8.19 10.0 1.0 7.37 50 43.5 13.8 0.068
(+)P6KE9.1A 8.65 9.55 1.0 7.78 50 44.8 13.4 0.068
(+)P6KE10 9.00 11.0 1.0 8.10 10 40.0 15.0 0.073
(+)P6KE10A 9.50 10.5 1.0 8.55 10 41.4 14.5 0.073
(+)P6KE11 9.90 12.1 1.0 8.92 5.0 37.0 16.2 0.075
(+)P6KE11A 10.5 11.6 1.0 9.40 5.0 38.5 15.6 0.075
(+)P6KE12 10.8 13.2 1.0 9.72 5.0 34.7 17.3 0.078
(+)P6KE12A 11.4 12.6 1.0 10.2 5.0 35.9 16.7 0.078
(+)P6KE13 11.7 14.3 1.0 10.5 5.0 31.6 19.0 0.081
(+)P6KE13A 12.4 13.7 1.0 11.1 5.0 33.0 18.2 0.081
(+)P6KE15 13.5 16.5 1.0 12.1 1.0 27.3 22.0 0.084
(+)P6KE15A 14.3 15.8 1.0 12.8 1.0 28.3 21.2 0.084
(+)P6KE16 14.4 17.6 1.0 12.9 1.0 25.5 23.5 0.086
(+)P6KE16A 15.2 16.8 1.0 13.6 1.0 26.7 22.5 0.086
(+)P6KE18 16.2 19.8 1.0 14.5 1.0 22.6 26.5 0.088
(+)P6KE18A 17.1 18.9 1.0 15.3 1.0 23.8 25.2 0.088
(+)P6KE20 18.0 22.0 1.0 16.2 1.0 20.6 29.1 0.090
(+)P6KE20A 19.0 21.0 1.0 17.1 1.0 21.7 27.7 0.090
(+)P6KE22 19.8 24.2 1.0 17.8 1.0 18.8 31.9 0.092
(+)P6KE22A 20.9 23.1 1.0 18.8 1.0 19.6 30.6 0.092
(+)P6KE24 21.6 26.4 1.0 19.4 1.0 17.3 34.7 0.094
(+)P6KE24A 22.8 25.2 1.0 20.5 1.0 18.1 33.2 0.094
(+)P6KE27 24.3 29.7 1.0 21.8 1.0 15.3 39.1 0.096
(+)P6KE27A 25.7 28.4 1.0 23.1 1.0 16.0 37.5 0.096
(+)P6KE30 27.0 33.0 1.0 24.3 1.0 13.8 43.5 0.097
(+)P6KE30A 28.5 31.5 1.0 25.6 1.0 14.5 41.4 0.097
(+)P6KE33 29.7 36.3 1.0 26.8 1.0 12.6 47.7 0.098
(+)P6KE33A 31.4 34.7 1.0 28.2 1.0 13.1 45.7 0.098
(+)P6KE36 32.4 39.6 1.0 29.1 1.0 11.5 52.0 0.099
(+)P6KE36A 34.2 37.8 1.0 30.8 1.0 12.0 49.9 0.099
(+)P6KE39 35.1 42.9 1.0 31.6 1.0 10.6 56.4 0.100
(+)P6KE39A 37.1 41.0 1.0 33.3 1.0 11.1 53.9 0.100
(+)P6KE43 38.7 47.3 1.0 34.8 1.0 9.7 61.9 0.101
(+)P6KE43A 40.9 45.2 1.0 36.8 1.0 10.1 59.3 0.101
(+)P6KE47 42.3 51.7 1.0 38.1 1.0 8.8 67.8 0.101
(+)P6KE47A 44.7 49.4 1.0 40.2 1.0 9.3 64.8 0.101
P6KE6.8 thru P6KE540A
Vishay General Semiconductor
Document Number: 88369
Revision: 22-Oct-08
For technical questions within your region, please contact one of the following:
PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com
www.vishay.com
3
(+)P6KE51 45.9 56.1 1.0 41.3 1.0 8.2 73.5 0.102
(+)P6KE51A 48.5 53.6 1.0 43.6 1.0 8.6 70.1 0.102
(+)P6KE56 50.4 61.6 1.0 45.4 1.0 7.5 80.5 0.103
(+)P6KE56A 53.2 58.8 1.0 47.8 1.0 7.8 77.0 0.103
(+)P6KE62 55.8 68.2 1.0 50.2 1.0 6.7 89.0 0.104
(+)P6KE62A 58.9 65.1 1.0 53.0 1.0 7.1 85.0 0.104
(+)P6KE68 61.2 74.8 1.0 55.1 1.0 6.1 98.0 0.104
(+)P6KE68A 64.6 71.4 1.0 58.1 1.0 6.5 92.0 0.104
(+)P6KE75 67.5 82.5 1.0 60.7 1.0 5.6 108 0.105
(+)P6KE75A 71.3 78.8 1.0 64.1 1.0 5.8 103 0.105
(+)P6KE82 73.8 90.2 1.0 66.4 1.0 5.1 118 0.105
(+)P6KE82A 77.9 86.1 1.0 70.1 1.0 5.3 113 0.105
(+)P6KE91 81.9 100 1.0 73.7 1.0 4.6 131 0.106
(+)P6KE91A 86.5 95.5 1.0 77.8 1.0 4.8 125 0.106
(+)P6KE100 90.0 110 1.0 81.0 1.0 4.2 144 0.106
(+)P6KE100A 95.0 105 1.0 85.5 1.0 4.4 137 0.106
(+)P6KE110 99.0 121 1.0 89.2 1.0 3.8 158 0.107
(+)P6KE110A 105 116 1.0 94.0 1.0 3.9 152 0.107
(+)P6KE120 108 132 1.0 97.2 1.0 3.5 173 0.107
(+)P6KE120A 114 126 1.0 102 1.0 3.6 165 0.107
(+)P6KE130 117 143 1.0 105 1.0 3.2 187 0.107
(+)P6KE130A 124 137 1.0 111 1.0 3.4 179 0.107
(+)P6KE150 135 165 1.0 121 1.0 2.8 215 0.108
(+)P6KE150A 143 158 1.0 128 1.0 2.9 207 0.108
(+)P6KE160 144 176 1.0 130 1.0 2.6 230 0.108
(+)P6KE160A 152 168 1.0 136 1.0 2.7 219 0.108
(+)P6KE170 153 187 1.0 138 1.0 2.5 244 0.108
(+)P6KE170A 162 179 1.0 145 1.0 2.6 234 0.108
(+)P6KE180 162 198 1.0 146 1.0 2.3 258 0.108
(+)P6KE180A 171 189 1.0 154 1.0 2.4 246 0.108
(+)P6KE200 180 220 1.0 162 1.0 2.1 287 0.108
(+)P6KE200A 190 210 1.0 171 1.0 2.2 274 0.108
(+)P6KE220 198 242 1.0 175 1.0 1.7 344 0.108
(+)P6KE220A 209 231 1.0 185 1.0 1.8 328 0.108
(+)P6KE250 225 275 1.0 202 1.0 1.7 360 0.110
(+)P6KE250A 237 263 1.0 214 1.0 1.7 344 0.110
(+)P6KE300 270 330 1.0 243 1.0 1.4 430 0.110
(+)P6KE300A 285 315 1.0 256 1.0 1.4 414 0.110
(+)P6KE350 315 385 1.0 284 1.0 1.2 504 0.110
(+)P6KE350A 333 368 1.0 300 1.0 1.2 482 0.110
(+)P6KE400 360 440 1.0 324 1.0 1.0 574 0.110
(+)P6KE400A 380 420 1.0 342 1.0 1.1 548 0.110
ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
DEVICE TYPE
BREAKDOWN
VOLTAGE
VBR AT IT (1)
(V)
TEST
CURRENT
IT
(mA)
STAND-OFF
VOLTAGE VWM
(V)
MAXIMUM
REVERSE
LEAKAGE
AT VWM (3) ID
(µA)
PEAK
PULSE
CURRENT
IPPM (2) (A)
MAXIMUM
CLAMPING
VOLTAG E AT
IPPM VC (V)
MAXIMUM
TEMPERATURE
COEFFICIENT
OF VBR (%/°C)
MIN. MAX.
P6KE6.8 thru P6KE540A
Vishay General Semiconductor
www.vishay.com For technical questions within your region, please contact one of the following:
PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com
Document Number: 88369
Revision: 22-Oct-08
4
Notes:
(1) Pulse test: tp ≤ 50 ms
(2) Surge current waveform per Fig. 3 and derate per Fig. 2ogm
(3) For bi-directional types with VWM of 10 V and less, the ID limit is doubled
(4) All terms and symbols are consistent with ANSI/IEEE C62.35
(+) Underwriters laboratory recognition for the classification of protectors (QVGQ2) under the UL standard for safety 497B and file number
E136766 for both uni-directional and bi-directional devices
Note:
(1) Automotive grade AEC-Q101 qualified
(+)P6KE440 396 484 1.0 356 1.0 0.95 631 0.110
(+)P6KE440A 418 462 1.0 376 1.0 1.00 602 0.110
P6KE480 432 528 1.0 389 1.0 0.88 686 0.110
P6KE480A 456 504 1.0 408 1.0 0.91 658 0.110
P6KE510 459 561 1.0 413 1.0 0.82 729 0.110
P6KE510A 485 535 1.0 434 1.0 0.86 698 0.110
P6KE540 486 594 1.0 437 1.0 0.78 772 0.110
P6KE540A 513 567 1.0 459 1.0 0.81 740 0.110
ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
DEVICE TYPE
BREAKDOWN
VOLTAG E
VBR AT IT (1)
(V)
TEST
CURRENT
IT
(mA)
STAND-OFF
VOLTAGE VWM
(V)
MAXIMUM
REVERSE
LEAKAGE
AT VWM (3) ID
(µA)
PEAK
PULSE
CURRENT
IPPM (2) (A)
MAXIMUM
CLAMPING
VOLTAGE AT
IPPM VC (V)
MAXIMUM
TEMPERATURE
COEFFICIENT
OF VBR (%/°C)
MIN. MAX.
THERMAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
PARAMETER SYMBOL VALUE UNIT
Typical thermal resistance, junction to lead RθJL 20 °C/W
Typical thermal resistance, junction to ambient RθJA 75 °C/W
ORDERING INFORMATION (Example)
PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE
P6KE6.8A-E3/54 0.432 54 4000 13" diameter paper tape and reel
P6KE6.8AHE3/54 (1) 0.432 54 4000 13" diameter paper tape and reel
P6KE6.8 thru P6KE540A
Vishay General Semiconductor
Document Number: 88369
Revision: 22-Oct-08
For technical questions within your region, please contact one of the following:
PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com
www.vishay.com
5
RATINGS AND CHARACTERISTICS CURVES
(TA = 25 °C unless otherwise noted)
Figure 1. Peak Pulse Power Rating Curve
Figure 2. Pulse Power or Current vs. Initial Junction Temperature
Figure 3. Pulse Waveform
t
d
- Pulse Width (s)
0.1
1
10
100
1.0 ms 10 ms
0.1 µs1.0 µs10 µs100 µs
Non-Repetitive Pulse
Waveform shown in Fig. 3
T
A
= 25 °C
P
PPM
- Peak Pulse Power (kW)
100
75
50
25
0
0 25 50 75 100 125 150 175 200
Peak Pulse Power (P
PP
) or Current (I
PP
)
Derating in Percentage, %
TJ - Initial Temperature (°C)
0
50
100
150
t
d
01.0 2.0 3.0 4.0
I
PPM
- Peak Pulse Current, % I
RSM
t - Time (ms)
tr = 10 µs
Peak Value
IPPM
Half Value -
IPPM
IPP
2
10/1000 µs Waveform
as defined by R.E.A.
TJ = 25 °C
Pulse Width (td)
is defined as the Point
where the Peak Current
decays to 50 % of IPPM
Figure 4. Typical Junction Capacitance Uni-Directional
Figure 5. Power Derating Curve
Figure 6. Maximum Non-Repetitive Forward Surge Current
10
100
1000
6000
10 100 2001.0
C
J
- Junction Capacitance (pF)
V
BR
- Breakdown Voltage (V)
TJ = 25 °C
f = 1.0 MHz
Vsig = 50 mVp-p
Measured at
Zero Bias
Measured at Stand-Off
Voltage VWM
6
5
4
3
2
1
0
0 25 50 75 100 125 150 175 200
L = 0.375" (9.5 mm)
Lead Lengths
P
D
- Power Dissipation (W)
T
L
- Lead Temperature (°C)
60 Hz
Resistive or
Inductive Load
200
100
50
10
1 5 10 50 100
I
FSM -
Peak Forward Surge Current (A)
Number of Cycles at 60 Hz
Uni-Directional Only
T
J
= T
J
max.
8.3 ms Single Half Sine-Wave
P6KE6.8 thru P6KE540A
Vishay General Semiconductor
www.vishay.com For technical questions within your region, please contact one of the following:
PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com
Document Number: 88369
Revision: 22-Oct-08
6
PACKAGE OUTLINE DIMENSIONS in inches (millimeters)
APPLICATION NOTE
This P6KE TVS series is a low cost commercial
product for use in applications where large voltage
transients can permanently damage voltage-sensitive
components.
The P6KE series device types are designed in a small
package size where power and space is a
consideration. They are characterized by their high
surge capability, extremely fast response time, and low
impedance, (Ron). Because of the unpredictable
nature of transients, and the variation of the
impedance with respect to these transients,
impedance, per se, is not specified as a parametric
value. However, a minimum voltage at low current
conditions (BV) and a maximum clamping voltage (Vc)
at a maximum peak pulse current is specified.
In some instances, the thermal effect (see Vc
Clamping Voltage) may be responsible for 50 % to
70 %. of the observed voltage differential when
subjected to high current pulses for several duty
cycles, thus making a maximum impedance
specification insignificant.
In case of a severe current overload or abnormal
transient beyond the maximum ratings, the Transient
Voltage Suppressor will initially fail 'short' thus tripping
the system's circuit breaker or fuse while protecting the
entire circuit. Curves depicting clamping voltage vs.
various current pulses are available from the factory.
Extended power curves vs. pulse time are also
available.
Figure 7. Typical Transient Thermal Impedance
tp - Pulse Duration (s)
Transient Thermal Impedance (°C/W)
10
100
1
0.1
0.001 0.01 0.1 1 10 100 1000
DO-204AC (DO-15)
0.034 (0.86)
0.028 (0.71)
DIA.
0.140 (3.6)
0.104 (2.6)
DIA.
1.0 (25.4)
MIN.
0.300 (7.6)
0.230 (5.8)
1.0 (25.4)
MIN.
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Packaging Information
www.vishay.com Vishay General Semiconductor
Revision: 01-Feb-13 1Document Number: 88869
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging Information
Notes
(1) Formerly sold by Vishay Telefunken® (Telefunken® is a registered trademark of Electro Holding GmbH).
• “P” and bold letter denotes preferred package code.
• A “T” suffix added to the packaging codes for SMA, SMB and SMC products indicates that the patented folded-frame construction is used.
This does not apply to TR and TR3 codes or TRANSZORB® TVS in SMA and SMB.
PACKAGING ORDERING CODE
ANTI-STATIC
PACKAGE CODE
PREFERRED
PACKAGE CODE PACKAGING DESCRIPTION
51 Bulk
52, 52T P DO-214AA (SMB)/DO-215AA (SMBG), 12 mm tape, 7" diameter plastic reel
2D P DO-218AB (SM5-8A), 24 mm tape, 13" diameter plastic reel, anode towards sprocket hole
2E DO-218AB (SM5-8A), 24 mm tape, 13" diameter plastic reel, cathode towards sprocket hole
2M Tube packaging for 5KP/6KA type lead formed components
2N DO-218AB, 24 mm tape, 13 "diameter plastic reel with dry packaging, anode towards sprocket hole
53 26 mm horizontal taping and ammo box packaging
54 P 52.4 mm horizontal tape, 13" diameter paper reel
5A, 5AT P DO-214AC (SMA), 12 mm tape, 13" diameter plastic reel
5B, 5BT P DO-214AA (SMB)/DO-215AA (SMBG), 12 mm tape, 13" diameter plastic reel
5CA P DO-214BA (GF1), 12 mm tape, 13" diameter plastic reel
57, 57T P DO-214AB (SMC)/DO-215AB (SMCG), 16 mm tape, 7" diameter plastic reel
6A P DO-221AC (SlimSMA), 12 mm tape, 7"diameter plastic reel
6B P DO-221AC (SlimSMA), 12 mm tape, 13"diameter plastic reel
9A, 9AT P DO-214AB (SMC)/DO-215AB (SMCG), 16 mm tape, 13" diameter plastic reel
61, 61T P DO-214AC (SMA), 12 mm tape, 7" diameter plastic reel
67A P DO-214BA (GF1), 12 mm tape, 7" diameter plastic reel
72 P Bulk pack for bridge and special axial-leaded formed devices
73 52.4 mm horizontal tape and ammo box packaging
77 P DFS bridge, 16 mm tape, 13" diameter paper reel
80 P TO-269AA (MB-S) bridge, 12 mm tape, 13" diameter paper reel
81 P TO-263AB 24 mm tape, 13" diameter reinforced hub plastic reel
8A P SMPD, 24 mm tape, 13" diameter plastic reel
8W P TO-263AB (wire bond) 24 mm tape, 13" diameter reinforced hub plastic reel
83 P DO-213AA (GL34) 8 mm tape, 13" diameter plastic reel
84A P DO-220AA (SMP) 12 mm tape, 7" diameter plastic reel
85A P DO-220AA (SMP) 12 mm tape, 13" diameter plastic reel
86A P TO-277A (SMPC), 12 mm tape, 7" diameter plastic reel
87A P TO-277A (SMPC), 12 mm tape, 13" diameter plastic reel
38 Lead forming bulk packaging in anti-static bags
89A P MicroSMP, 8 mm tape, 7" diameter plastic reel
90 Euroform, reel, cathode first off reel, lead coated
91 Euroform, ammo pack, cathode first out of ammo pack, lead coated
92 Euroform, reel, cathode last off reel, lead coated
93 Euroform, ammo pack, cathode last out of ammo pack, lead coated
45 P Anti-static tube packaging for Bridge and Power Pack
4W P Anti-static tube packaging for wire bond TO-220, ITO-220, TO-262 and TO-263
96 P DO-213AB (GL41), 12 mm tape, 7" diameter plastic reel
97 P DO-213AB (GL41), 12 mm tape, 13" diameter plastic reel
98 P DO-213AA (GL34), 8 mm tape, 7" diameter plastic reel
100 MPG06 pseudo radial tape, cathode first out of ammo pack
H P Tape in 7" diameter plastic reel
I P Tape in 13" diameter plastic reel
TR P DO-214AC (SMA), 12 mm tape, 7" diameter plastic reel (1)
TR3 P DO-214AC (SMA), 12 mm tape, 13" diameter plastic reel (1)
Packaging Information
www.vishay.com Vishay General Semiconductor
Revision: 01-Feb-13 2Document Number: 88869
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
BULK PACKAGING
CASE TYPES
PREFERRED
PACKAGE
CODE
PACKAGING
BOX SIZE QUANTITY
INCHES cm EA.
DF-M, DF-S, DFL-S 45 Anti-static plastic tubes 17.4 length 44.1 length 50
GSIB-3S 45 Anti-static plastic tubes 25.1 length 63.9 length 20
GSIB-5S, PB 45 Anti-static plastic tubes 24.2 length 61.5 length 20
GBU, BU 45 Anti-static plastic tubes 18.5 length 47 length 20
GBL 45 Anti-static plastic tubes 17.5 length 44.5 length 20
KBPM 45 Anti-static plastic tubes 18.5 length 47 length 30
TO-220AB/AC, ITO-220AC/AB, TO-262AA 45, 4W Anti-static plastic tubes 21.0 length 53.7 length 50
TO-247AD 45 Anti-static plastic tubes 20.0 length 50.8 length 30
TO-269AA (MB-S) 45 Anti-static plastic tubes 20.3 x 0.41 51.5 x 1.04 100
KBPM 51 Anti-static PVC tray 12.5 x 6.5 x 1.25 31.7 x 16.5 x 3.17 600
GBL 51 Anti-static PVC tray 12.5 x 6.1 x 1.0 30.9 x 15.5 x 2.5 400
GBPC12-35W 51 Paper box 12.5 x 12.5 x 1.7 31.7 x 31.7 x 4.3 100
GBPC1, GBPC6 51 Paper box 7.5 x 7.5 x 1.43 19.0 x 19.0 x 3.6 100
KBL 51 Anti-static PVC tray 12.2 x 6.1 x 1.5 30.9 x 15.5 x 3.8 300
GBPC12-35 51 Paper box 12.5 x 12.5 x 1.7 31.7 x 31.7 x 4.3 100
KBU4, 6, 8 51 Anti-static PVC tray 12.2 x 6.1 x 1.5 30.9 x 15.5 x 3.8 250
WOG, 2WOG 51 Plastic bags - - 100
GBU, /BU 51 Paper tray 13.1 x 6.6 x 1.2 33.2 x 17.2 x 3.0 250
KBPM 72 Paper box 7.4 x 7.4 x 1.5 18.8 x 18.8 x 3.8 200
Packaging Information
www.vishay.com Vishay General Semiconductor
Revision: 01-Feb-13 3Document Number: 88869
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
AXIAL-LEADED TAPE AND REEL PACKAGING
All axial-leaded devices are packed in accordance with EIA standard RS-296-E. The diagrams given below refer to these
specifications.
Fig. 1 Fig. 2
TABLE 1 - AMMO PACK PACKAGING
PACKAGING AVAILABLE PRODUCT
OUTLINES
PREFERRED
PACKAGE CODE
DIMENSION
A
DIMENSION
B
DIMENSION
C
QUANTITY
BOX
26 mm horizontal tape,
ammo pack
DO-204AL (DO-41), MPG06
DO-204AC
P300
53
53
53
9.7"
(247 mm)
1.7"
(44 mm)
3.7"
(95 mm)
3.0K
1.5K
0.75K
52 mm horizontal tape,
ammo pack
DO-204AL, MPG06
DO-204AC
DO201AD, GP20
P600
73
73
73
73
10.0"
(255 mm)
3.15"
(80 mm)
4.53"
(115 mm)
3.0K
2.0K
1.0K
0.3K
Radial
(avisert, panasert, euroform)
vertical tape
GP10-E, RGP10-E,
GP10-E, RGP10-E 91, 93 13.4"
(340 mm)
1.8"
(47 mm)
7.9"
(200 mm)
2.0K
2.5K
2.0K
Pseudo/radial tape,
ammo pack MPG06 100 13.4"
(340 mm)
1.8"
(47 mm)
7.9"
(200 mm) 2.0K
A
C
B
Inspection Hole
(Both Sides)
Ammo Pack can be Opened on Either Side,
Depending on Desired Device Polarity
Component Pitch A 2, 3
Inside Tape Spacing B 2, 3
Lead to Lead Eccentricity |D1 - D2| -
Lead Extension K -
Lead Bending E 2
Cumulative Pitch P 3
Exposed Adhesive S -
Tape Width T -
All polarized components shall be oriented in the same direction
Description Symbol
E
D1D2
A
P
K
S
B
W
|D1 - D2| = 1.4 (0.055) Max. 0.8 (0.031) Max. Typ. 0.0
0.8 (0.031)
Max.
Dimensions A, M, K, P, S and T apply to both sides
Dimensions in millimeters (inches)
E
T
6.0 ± 0.4
(0.236 ± 0.0157)
The “C” dimension of Fig. 2 is between flanges of the component
reel and shall be 1.5 mm (0.059") to 8.00 mm (0.315") greater than
the overall taped component width “W” (Fig. 1). Where “W”
dimension is 68.2 mm (2.68") max.
38.1 (1.50) Dia.
14.3 (0.56) Dia.
D Dia.
(Table 2)
Kraft
Paper
91.9 (3.62) Dia.
50.8 (2.00) Dia.
Cathode Lead
Colored Tape
C
Anode Lead
White Tape
Packaging Information
www.vishay.com Vishay General Semiconductor
Revision: 01-Feb-13 4Document Number: 88869
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
AXIAL-LEADED TAPE AND REEL PACKAGING
Note
• Package codes, 61/5A, 52/5B are matrix-frame constructions for TRANSZORB® TVS in SMA and SMB only.
TABLE 2 - REEL AND AMMO PACK TAPING SPECIFICATIONS
COMPONENT
CASE TYPE
PREFERRED
PACKAGE
CODE
UNITS
PER REEL
COMPONENT
PITCH
“A” Fig. 1
INSIDE TAPE
SPACING “B”
Fig. 1
REEL DIMENSION
“D” Fig. 2
LEAD BENDING
“E” Fig. 1
EA. INCHES mm INCHES mm INCHES mm INCHES mm
1.5KA (PAR) 54 1400 0.395 10.0 2.06 52.4 13.0 330 0.047 1.2
DO-204AC 54 4000 0.200 5.0 2.06 52.4 13.0 330 0.047 1.2
DO-201AD 54 1400 0.395 10.0 2.06 52.4 13.0 330 0.047 1.2
DO-204AL 54 5500 0.200 5.0 2.06 52.4 13.0 330 0.047 1.2
DFS Surface Mount 77 1500
Fig. 13
- - 13.0 330 Fig. 13 -
DO-214BA (GF1) 67A/5CA 1500/6500 - - 7.0/13.0 178/330 Fig. 13 -
DO-213AA (GL34) 98/83 2500/9000 - - 7.0/13.0 178/330 Fig. 13 -
DO-213AB (GL41) 96/97 1500/5000 - - 7.0/13.0 178/330 Fig. 13 -
GP10E Radial Fig. 7 and Fig. 8 2500 0.500 12.7 - - 13.0 330 0.079 2.0
GP10E 54 5500 0.200 5.0 2.06 52.4 13.0 330 0.047 1.2
GP20/1.5KE 54 1400 0.395 10.0 2.06 52.4 13.0 330 0.047 1.2
MPG06 100 5500 0.200 5.0 2.06 52.4 13.0 330 0.047 1.2
P600 54 800 0.395 10.0 2.06 52.4 13.0 330 0.047 1.2
DO-220AA (SMP) 84A/85A 3000/10 000
Fig. 13
- - 7.0/13.0 178/330 Fig. 13 -
SMPD 8A 2000 - - 13.0 330 Fig. 13 -
MicroSMP 89A 4500 - - 7.0 178 Fig. 13 -
TO-277A (SMPC) 86A/87A 1500/6500 - - 7.0/13.0 178/330 Fig. 13 -
DO-214AC (SMA) 61, 61T, TR/5A,
5AT, TR3 1800/7500 - - 7.0/13.0 178/330 Fig. 13 -
DO-214AA (SMB)/
DO-215AA (SMBG) 52, 52T/5B, 5BT 750/3200 - - 7.0/13.0 178/330 Fig. 13 -
DO-214AB (SMC)/
DO-215AB (SMCG) 57T/9AT 850/3500 - - 7.0/13.0 178/330 Fig. 13 -
DO-218AB 2D 750 - - 13.0 330 Fig. 13 -
TO-263AB 81, 8W 800 - - 13.0 330 Fig. 13 -
TO-269AA (MB-S) 80 3000 - - 13.0 330 Fig. 13 -
DO-221AC
(SlimSMA) 6A/6B 3500/14 000 - - 7.0/13.0 178/330 Fig. 13 -
TABLE 3 - COMPONENT AND INSIDE HORIZONTAL TAPE SPACING
COMPONENT
BODY DIAMETER
COMPONENTS SPACING
A (LEAD TO LEAD)
INSIDE TAPE
SPACING "B"
CUMULATIVE
PITCH TOLERANCE
0 mm to 5 mm
(0.0" to 0.197")
5.0 mm ± 0.5 mm
(0.197" ± 0.020")
26 mm + 1.5 mm/- 0.0 mm
(1.024" + 0.059"/- 0.0")
Not to exceed 1.5 mm (0.059")
over 6 consecutive components
0 mm to 5 mm
(0.0" to 0.197")
5.0 mm ± 0.5 mm
(0.197" ± 0.020")
52.4 mm + 1.5 mm/- 0.4 mm
(2.062" + 0.059"/- 0.016")
5.01 mm to 10 mm
(0.197" to 0.394")
10 mm ± 0.5 mm
(0.394" ± 0.020")
52.4 mm + 1.5 mm/- 0.4 mm
(2.062" + 0.059"/- 0.016")
Packaging Information
www.vishay.com Vishay General Semiconductor
Revision: 01-Feb-13 5Document Number: 88869
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DIMENSIONS in millimeters (inches)
Fig. 3 - Euroform
Fig. 4 - Panasert
Available for GP10 Products only Utilizing 0.65 mm (0.025") Diameter Leads for
Euroform tape by adding suffix “E” (GP10GE, 1N4004GPE). Lead coating is standard.
Tape
5.68 (0.224)
4.68 (0.184)
(Center to Center)
20.5
18.5
(0.807)
(0.728) 11.0
MAX.
(0.433)
4.55 (0.179)
3.15 (0.124)
(Center to Center)
1.0 MAX. (2)
(0.40)
(Center to Center)
6.5 MAX.
(0.256)
16.5 (0.650)
15.5 (0.610)
4.3 (0.169)
3.7 (0.146)
DIA.
2.5
MIN.
(0.098)
12.0 MAX.
(0.472)
7.35 (0.29)
5.35 (0.21)
0.6 MAX.
(0.024)
9.75 (0.384)
8.50 (0.335)
19.0 (0.748)
17.5 (0.689)
13.5 (0.531)
12.5 (0.492) User Direction Feed
32.0 (1.26)
23.0 (0.905)
2.72 (0.107)
2.03 (0.080)
Body DIA.
0.65 (0.0256)
0.55 (0.022)
Lead DIA.
± 1.0 (2)
(± 0.039)
0.6 (0.025)
0.4 (0.016)
13.0 (0.512)
12.4 (0.488)
12.7 (0.50)
(Nominal)
A (1)
B (1)
Note:
(1) Measurement
difference between
leads, A and B =
0.4 (0.016) MAX.
(2) Component
Alignment
Tape
19.0 (0.748)
17.5 (0.689)
9.75 (0.384)
8.50 (0.335)
User Direction Feed
16.0 MIN.
(0.630)
32.0 (1.26)
23.0 (0.905)
5.5 MIN.
(0.217)
(Center to Center)
6.5 MAX.
(0.256)
4.3 (0.169)
3.7 (0.146)
DIA.
5.68 (0.224)
4.68 (0.184)
(Center to Center)
16.5 (0.650)
15.5 (0.610)
1.0 MAX. (1)
(0.40)
7.0 MIN.
(0.276)
1.3 MIN.
(0.059)
2.72 (0.107)
2.03 (0.080)
Body DIA.
0.86 (0.034)
0.55 (0.022)
Lead DIA.
± 1.0 (1)
(± 0.039)
0.6 (0.025)
0.4 (0.016)
13.0 (0.512)
12.4 (0.488)
11.0
MAX.
(0.433)
4.55 (0.179)
3.15 (0.124)
(Center to Center)
12.7 (0.50)
(Nominal)
Note:
(1) Component Alignment
Packaging Information
www.vishay.com Vishay General Semiconductor
Revision: 01-Feb-13 6Document Number: 88869
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DIMENSIONS in millimeters (inches)
Fig. 5 - Avisert
Fig. 6 - Pseudo Radial
Note:
(1) Component Alignment
Available only for GP10 style products utilizing 0.65 mm (0.025") or 0.76 mm (0.030")
diameter leads for Panasert and Avisert tape. Lead coating is available on GP10 products only.
User Direction Feed
13.0 (0.512)
12.4 (0.488)
6.5 MAX.
(0.256)
5.68 (0.224)
4.68 (0.184)
(Center to Center)
(Center to Center)
1.0 MAX. (1)
(0.40)
16.5 (0.650)
15.5 (0.610)
4.55 (0.179)
3.15 (0.124)
(Center to Center)
4.3 (0.169)
3.7 (0.146)
2.72 (0.107)
2.03 (0.080)
Body DIA.
0.86 (0.034)
0.55 (0.022)
Lead DIA.
± 1.0 (1)
(± 0.039)
3.0 MAX.
(0.118)
0.6 (0.025)
0.4 (0.016)
16.0 MIN.
(0.630)
32.0 (1.26)
23.0 (0.905) 5.5 MIN.
(0.217)
Tape
19.0 (0.748)
17.5 (0.689)
9.75 (0.384)
8.50 (0.335)
11.0
MAX.
(0.433)
12.7 (0.50)
(Nominal)
Standard Polarity Cathode Oriented Away from Sprocket Holes (Optional Polarity Cathode Oriented Toward Sprocket Holes)
16.0 (0.63)
MIN.
2.0 (0.079)
MAX.
11.0
(4.33)
MAX.
13.0 (0.51)
12.4 (0.49)
4.3 (0.169)
3.7 (0.146)
DIA.
12.5
(0.492)
MIN.
Tape
19.0 (0.748)
17.5 (0.689)
9.75 (0.384)
8.50 (0.335)
± 1.0 (1)
(± 0.039)
1.0 (0.039) MAX.
0.6 (0.025)
0.4 (0.016)
Available only for MPG06 Product in Ammo Pack in Accordance with EIA Standard RS-468-A Utilizing
0.61 mm (0.024") Diameter Leads. Maximum Cumulative Pitch Tolerance: 1.0 mm (0.039")/20 Pitch.
User Direction Feed
0.66 (0.026)
0.55 (0.022)
Lead DIA.
2.54 (0.01)
2.29 (0.090)
Body DIA.
3.2 (0.125)
2.9 (0.115)
3.06 (0.118)
MAX.
5.68 (0.224)
4.68 (0.184)
4.51 (0.178)
3.11 (0.122)
(Center to Center)
12.7 (0.50)
(Nominal)
1.0 MAX. (1)
(0.40)
Note:
(1) Component Alignment
Packaging Information
www.vishay.com Vishay General Semiconductor
Revision: 01-Feb-13 7Document Number: 88869
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RADIAL TAPE PACKAGING
Fig. 7 and Fig. 8 - Reel and Ammo Box Packaging
Fig. 9 - Reel Dimensions
Notes
• “C” dimension between the reel flanges shall be governed by the overall width of the taped components and shall be 1.5 mm (0.057") to
8.0 mm (0.315") greater than the overall width
• All leaded devices are packaged in accordance with EIA standard RS-468-A specification and are available on reel or in fan fold box (ammo
pack)
• All dimensions are in millimeters and (inches). The above packaging is only available from Taiwan.
PKG90
PKG92
PKG91
PKG93
PREFERRED PACKAGE CODE
EUROFORM PKG90, PKG91, PKG92, PKG93
55 (2.17) MAX. 330 (13.0) MAX.
Core DIA.
34.9 to 102
(1.37 to 4.02)
“C”
Arbor Hole DIA.
30 ± 5 ID
(1.181 ± 0.197)
Packaging Information
www.vishay.com Vishay General Semiconductor
Revision: 01-Feb-13 8Document Number: 88869
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SURFACE MOUNT TAPE AND REEL PACKAGING
Fig. 10
Fig. 11
Fig. 12
Component
Cavity
Embossed Carrier
Tape
Top Cover Tape
Thickness:
0.10 mm (0.004")
Max.
R Ref.
Bending
Radius
Tape with
Components shall
Pass Around
Bending Radius
without Damage,
for Reels with Hub
Diameters
Approaching
Minimum
Dimension
B
NA
T
D
C
G
DIMENSIONS in millimeters (inches)
TAPE SIZE A
MAX.
B
MIN. C D
MIN.
N
MIN.
G
MAX.
T
MAX.
8 mm (0.315) 330 ± 2.0 (13.0 ± 0.079)
178 ± 2.0 (7.0 ± 0.079) 1.5 (0.059) 13.0 ± 0.20
(0.51 ± 0.0008) 20.2 (0.795) 50 (1.97) 9.9 (0.389) 14.4 (0.567)
12 mm (0.472) 330 ± 2.0 (13.0 ± 0.079)
178 ± 2.0 (7.0 ± 0.079) 1.5 (0.059) 13.0 ± 0.20
(0.51 ± 0.0008) 20.2 (0.795) 50 (1.97) 14.4 (0.567) 18.4 (0.724)
16 mm (0.630) 330 ± 2.0 (13.0 ± 0.079)
178 ± 2.0 (7.0 ± 0.079) 1.5 (0.059) 13.0 ± 0.20
(0.51 ± 0.0008) 20.2 (0.795) 50 (1.97) 18.4 (0.724) 22.4 (0.802)
24 mm (0.945) 330 ± 2.0 (13.0 ± 0.079)
178 ± 2.0 (7.0 ± 0.079) 1.5 (0.059) 13.0 ± 0.20
(0.51 ± 0.0008) 20.2 (0.795) 50 (1.97) 26.4 (1.039) 30.4 (1.197)
Packaging Information
www.vishay.com Vishay General Semiconductor
Revision: 01-Feb-13 9Document Number: 88869
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SURFACE MOUNT TAPE AND REEL PACKAGING
Fig. 13
Notes
(1) A0, B0, and K0 are determined by the maximum dimensions of the component size. The clearance between the component and the cavity
must be within 0.05 mm (0.002") min. to 0.5 mm (0.02") max. for 8 mm tape and 12 mm tape, 0.15 mm (0.066") min. to 0.90 mm (0.035")
max. for 16 mm tape and 0.15 mm (0.006") min. to 1.0 mm (0.59") max. for 24 mm tape.
(2) All surface mount components are packed in accordance with EIA standard 481-C
8 mm, 12 mm, 16 mm, AND 24 mm EMBOSSED TAPE in millimeters (inches)
TAPE SIZE D0E1P0P2A0, B0, K0S1 MIN. T MAX. T1 MAX.
8 mm, 12 mm 1.5 ± 0.1
(0.059 ± 0.004)
1.75 ± 0.1
(0.069 ± 0.004)
4.0 ± 0.1
(0.157 ± 0.004)
2.0 ± 0.05
(0.79 ± 0.002) (1) 0.6
(0.024)
0.600
(0.024)
0.1
(0.004)
16 mm, 24 mm 2.0 ± 0.1
(0.79 ± 0.004)
DIMENSIONS in millimeters (inches)
CASE TYPE TAPE
SIZE B1 MAX. D1 MIN. E2 MAX. F P1R REF. T2 MAX. W
DO-213AA (GL34) 8
(0.315)
4.2
(0.165) 1.0
(0.39)
6.25
(0.246) 3.5 ± 0.05
(0.138 ± 0.002)
4.0 ± 0.10
(0.57 ± 0.004)
25
(0.984)
2.4
(0.094) 8.0 ± 0.30
(0.315 ± 0.012)
MicroSMP 3.28
(0.129)
6.05
(0.238)
1.919
(0.076)
DO-213AB (GL41)
12
(0.472)
8.2
(0.323)
1.5
(0.059)
10.25
(0.404)
5.5 ± 0.05
(0.217 ± 0.002)
30
(1.181)
4.5
(0.177)
12.0 ± 0.30
(0.472 ± 0.012)
DO-214BA (GF1) 3.25
(0.128)
DO-214AC(SMA) 2.64
(0.104)
DO-220AA (SMP) 1.84
(0.072)
TO-277A (SMPC) 7.0
(2.76)
8.0 ± 0.10
(0.315 ± 0.004)
1.43
(0.056)
DO-214AA (SMB)/
DO-215AA (SMBG)
8.2
(0.323)
2.77
(0.109)
DO-214AB (SMC)/
DO-215AB (SMCG) 16
(0.630)
12.1
(0.476)
14.25
(0.561)
7.5 ± 0.05
(0.295 ± 0.002)
2.64
(0.104) 16.0 ± 0.2
(0.630 ± 0.008)
DFS 12.0 ± 0.10
(0.472 ± 0.004)
3.91
(0.154)
TO-263AB
DO-218AB 24
(0.945)
20.1
(0.791)
22.25
(0.876)
11.5 ± 0.1
(0.453 ± 0.004)
16.0 ± 0.10
(0.630 ± 0.004)
5.31
(0.209) 24.0 ± 0.3
(0.945 ± 0.008)
SMPD 1.5
(0.059)
12.0 ± 0.10
(0.472 ± 0.004)
2.35
(0.093)
DO-221AC
(SlimSMA)
12
(0.472)
6.2
(0.244)
10.25
(0.404)
5.5 ± 0.05
(0.217 ± 0.002)
4.0 ± 0.10
(0.157 ± 0.001)
1.53
(0.060)
12.0 ± 0.3
(0.472 ± 0.012)
Notes
(1)
For machine reference only, including draft and
radii concentric around B
0
(2)
See note 1 and table
K0
T
P0
B1
(1)
F
E
W
P2
P
B0
A
0
(2)
0
1
E2
D
D1 for components
2.0 mm x 1.2 mm and larger
Top
Cover
Tape
De-Reeling Direction
T
T
2
10 P0itches Cumulative Tolerance on Tape ± 0.2
1
S1