OPA2227-EP www.ti.com SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 HIGH PRECISION, LOW NOISE OPERATIONAL AMPLIFIER Check for Samples: OPA2227-EP FEATURES 1 * * * * * * * * Low Noise: 3 nV/Hz Wide Bandwidth: 8 MHz, 2.3 V/s Settling Time: 5 s High CMRR: 138 dB (Typical) High Open-Loop Gain: 160 dB (Typical) Low Input Bias Current: 10 nA Maximum at 25C Low Offset Voltage: 100 V Maximum at 25C Wide Supply Range: 2.5 V to 18 V APPLICATIONS * * * * * * * * Data Acquisition Telecom Equipment Geophysical Analysis Vibration Analysis Spectral Analysis Professional Audio Equipment Active Filters Power Supply Control SUPPORTS DEFENSE, AEROSPACE, AND MEDICAL APPLICATIONS * * * * * * * Controlled Baseline One Assembly and Test Site One Fabrication Site Available in Military (-55C to 125C) Temperature Range (1) Extended Product Life Cycle Extended Product-Change Notification Product Traceability D PACKAGE (TOP VIEW) Out A -In A (1) 1 2 +In A 3 V- 4 A B 8 V+ 7 Out B 6 -In B 5 +In B Additional temperature ranges available - contact factory DESCRIPTION The OPA2227 operational amplifier combines low noise and wide bandwidth with high precision to make it the ideal choice for applications requiring both ac and precision dc performance. The OPA2227 is unity-gain stable and features high slew rate (2.3 V/s) and wide bandwidth (8 MHz). The OPA2227 operational amplifier is ideal for professional audio equipment. In addition, low quiescent current and low cost make them ideal for portable applications requiring high precision. The OPA2227 operational amplifier is a pin-for-pin replacement for the industry standard OP-27 with substantial improvements across the board. The dual and quad versions are available for space savings and perchannel cost reduction. The OPA2227 is available in an SOIC-8 package. Operation is specified from -55C to 125C. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2012, Texas Instruments Incorporated OPA2227-EP SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) TA PACKAGE TOP-SIDE MARKING -55C to 125C SOIC-8 - D 2227EP (1) ORDERABLE PART NUMBER VID NUMBER TRANSPORT MEDIA OPA2227MDREP V62/12610-01XE Tape and Reel, large OPA2227MDEP V62/12610-01XE-T Tube For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VALUE UNIT 18 V Voltage (V-) - 0.7 to (V+) + 0.7 V Current 20 mA Supply voltage Signal input terminals Output short-circuit (to ground) (2) (1) (2) Continuous Operating temperature -55 to 125 C Storage temperature -65 to 150 C Junction temperature 150 C Lead temperature (soldering, 10 s) 300 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. One channel per package. THERMAL INFORMATION OPA2227 THERMAL METRIC (1) D UNITS 8 PINS JA Junction-to-ambient thermal resistance (2) 91.9 JCtop Junction-to-case (top) thermal resistance (3) 39.9 (4) JB Junction-to-board thermal resistance JT Junction-to-top characterization parameter (5) JB Junction-to-board characterization parameter (6) 39.6 (7) N/A JCbot (1) (2) (3) (4) (5) (6) (7) 2 Junction-to-case (bottom) thermal resistance 40.6 3.9 C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88. The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB temperature, as described in JESD51-8. The junction-to-top characterization parameter, JT, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining JA, using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, JB, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining JA , using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88. Spacer Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP OPA2227-EP www.ti.com SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 ELECTRICAL CHARACTERISTICS At TA = 25C, VS = 5 V to 15 V, RL = 10 k (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNIT V OFFSET VOLTAGE Input offset voltage (VOS) 5 100 vs Temperature, TA = -55C to 125C 10 250 vs Temperature (dVOS/dT), TA = -55C to 125C 0.1 vs Power supply (PSRR) TA = -55C to 125C VS = 2.5 V to 18 V 0.5 vs Time Channel separation (dual) V V/C 2.1 V/V 0.2 V/mo dc 0.2 V/V f = 1 kHz, RL = 5 k 110 dB INPUT BIAS CURRENT Input bias current (IB) 2.5 TA = -55C to 125C 10 nA 10 nA See Typical Characteristics Input offset current (IOS) 2.5 TA = -55C to 125C See Typical Characteristics NOISE Input voltage noise, f = 0.1 Hz to 10 Hz Input voltage noise density (en) f = 10 Hz 90 nVp-p 15 nVrms 3.5 nV/Hz f = 100 Hz 3 nV/Hz f = 1 kHz 3 nV/Hz 0.4 pA/Hz Current noise density (in), f = 1 kHz INPUT VOLTAGE RANGE Common-mode voltage range (VCM) TA = -55C to 125C (V-) + 2 Common-mode rejection (CMRR) VCM = (V-) + 2 V to (V+) - 2 V TA = -55C to 125C (V+) - 2 V 120 138 dB 108 138 dB INPUT IMPEDANCE Differential Common-mode Open-loop voltage gain (AOL) 107 || 12 || pF VCM = (V-) + 2 V to (V+) - 2 V 9 || pF 10 || 3 OPEN-LOOP GAIN Open-loop voltage gain (AOL) VO = (V-) + 2 V to (V+) - 2 V, RL = 10 k TA = -55C to 125C VO = (V-) + 3.5 V to (V+) - 3.5 V, RL = 600 TA = -55C to 125C 132 160 112 160 132 160 112 160 dB FREQUENCY RESPONSE Gain bandwidth product (GBW) Slew rate (SR) Settling time: 8 MHz 2.3 V/s 0.1% G = 1, 10-V Step, CL = 100 pF 5 s 0.01% G = 1, 10-V Step, CL = 100 pF 5.6 s VIN x G = VS 1.3 s 0.00005 % Overload recovery time Total harmonic distortion + noise (THD+N) f = 1 kHz, G = 1, VO = 3.5 Vrms OUTPUT Voltage output TA = -55C to 125C RL = 10 k (V-) + 2 (V+) - 2 TA = -55C to 125C RL = 600 (V-) + 3.5 (V+) - 3.5 Short-circuit current (ISC) 45 Capacitive load drive (CLOAD) V mA See Typical Characteristics POWER SUPPLY Specified voltage range (VS) Operating voltage range Quiescent current (per amplifier) (IQ) IO = 0 A 5 15 V 2.5 18 V 3.7 3.95 Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP 3 OPA2227-EP SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 www.ti.com ELECTRICAL CHARACTERISTICS (continued) At TA = 25C, VS = 5 V to 15 V, RL = 10 k (unless otherwise noted). PARAMETER TEST CONDITIONS TA = -55C to 125C MIN TYP IO = 0 A MAX UNIT 4.30 mA TEMPERATURE RANGE Specified temperature range -55 125 C Operating temperature range -55 125 C Storage temperature range -65 150 C xxx Estimated Life (Hours) 1000000 100000 10000 1000 125 130 135 140 145 150 Continuous T J ( C) A. See datasheet for absolute maximum and minimum recommended operating conditions. B. Silicon operating life design goal is 10 years at 105C junction temperature (does not include package interconnect life). Figure 1. OPA2227-EP Wirebond Life Derating Chart 4 Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP OPA2227-EP www.ti.com SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 TYPICAL CHARACTERISTICS At TA = 25C, RL = 10 k, VS = 15 V (unless otherwise noted). OPEN-LOOP GAIN/PHASE vs FREQUENCY 180 0 160 -20 140 +CMRR -100 PSRR, CMRR (dB) -80 Phase () AOL (dB) 120 -60 100 80 140 -40 G 120 POWER SUPPLY AND COMMON-MODE REJECTION RATIO vs FREQUENCY 100 60 -120 40 -140 20 -160 0 -180 -20 -200 10k 100k 1M 10M 100M -0 -20 0.01 0.10 1 10 100 1k +PSRR 80 60 -PSRR 40 0.1 Frequency (Hz) 1 10 100 1k 10k 100k 1M Frequency (Hz) TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY INPUT VOLTAGE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY 0.01 100k 10k THD+Noise (%) Voltage Noise (nV/Hz) Current Noise (fA/Hz) VOUT = 3.5Vrms Current Noise 1k 100 10 0.001 0.0001 G = 1, RL = 10k Voltage Noise 0.00001 1 0.1 1 10 100 1k 20 10k 100 INPUT NOISE VOLTAGE vs TIME 10k 20k CHANNEL SEPARATION vs FREQUENCY Channel Separation (dB) 140 50nV/div 1k Frequency (Hz) Frequency (Hz) 120 100 80 Dual and quad devices. G = 1, all channels. Quad measured Channel A to D, or B to C; other combinations yield similiar or improved rejection. 60 40 1s/div 10 100 1k 10k 100k 1M Frequency (Hz) Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP 5 OPA2227-EP SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) At TA = 25C, RL = 10 k, VS = 15 V (unless otherwise noted). VOLTAGE NOISE DISTRIBUTION (10Hz) WARM-UP OFFSET VOLTAGE DRIFT 24 10 Offset Voltage Change (V) Percent of Units (%) 8 16 8 6 4 2 0 -2 -4 -6 -8 0 -10 0 3.16 3.25 3.34 3.43 3.51 3.60 0 3.69 3.78 50 Noise (nV/Hz) AOL, CMRR, PSRR vs TEMPERATURE 160 Input Bias Current (nA) AOL, CMRR, PSRR (dB) PSRR 110 100 90 80 10 0 -10 -20 -30 -40 -50 -25 0 25 50 75 100 -50 -60 -40 -20 125 0 Temperature ( C) INPUT OFFSET CURRENT vs TEMPERATURE 100 120 140 SHORT-CIRCUIT CURRENT vs TEMPERATURE Short-Circuit Current (mA) 5 4 3 2 1 0 -1 -2 -60 -40 -20 20 40 60 80 Temperature (C) 60 6 Input Offset Current (nA) 300 20 70 6 250 30 CMRR 130 60 -75 200 INPUT BIAS CURRENT vs TEMPERATURE 150 120 150 40 AOL 140 100 Time from Power Supply Turn-On (s) 0 20 40 60 80 Temperature (C) 100 120 140 50 40 -ISC +ISC 30 20 10 0 -75 -50 -25 0 25 50 75 100 125 Temperature (C) Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP OPA2227-EP www.ti.com SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 TYPICAL CHARACTERISTICS (continued) At TA = 25C, RL = 10 k, VS = 15 V (unless otherwise noted). QUIESCENT CURRENT vs TEMPERATURE QUIESCENT CURRENT vs SUPPLY VOLTAGE 3.8 18V 15V 12V 10V 4.5 4.0 Quiescent Current (mA) Quiescent Current (mA) 5.0 5V 2.5V 3.5 3.0 2.5 3.6 3.4 3.2 3.0 2.8 -60 -40 -20 0 20 40 60 80 100 120 140 0 2 4 6 Temperature ( C) 10 12 14 16 18 20 CHANGE IN INPUT BIAS CURRENT vs POWER SUPPLY VOLTAGE SLEW RATE vs TEMPERATURE 2.0 3.0 Curve shows normalized change in bias current with respect to VS = 10V. Typical I B may range from -2nA to +2nA at V S = 10V. 1.5 2.5 Positive Slew Rate 1.0 Negative Slew Rate 2.0 IB (nA) Slew Rate (V/V) 8 Supply Voltage (V) 1.5 0.5 0 -0.5 1.0 -1.0 RLOAD = 2k CLOAD = 100pF 0.5 -1.5 -2.0 0 -75 -50 -25 0 25 50 75 100 0 125 5 10 CHANGE IN INPUT BIAS CURRENT vs COMMON-MODE VOLTAGE 1.5 30 35 40 VS = 15V, 10V Step CL = 1500pF RL = 2k Settling Time (s) IB (nA) 25 SETTLING TIME vs CLOSED-LOOP GAIN 0.5 0 20 100 Curve shows normalized change in bias current with respect to VCM = 0V. Typical I B may range from -2nA to +2nA at V CM = 0V. 1.0 15 Supply Voltage (V) Temperature ( C) VS = 15V -0.5 0.01% 10 0.1% VS = 5V -1.0 1 -1.5 -15 -10 -5 0 5 10 15 1 Common-Mode Voltage (V) 10 Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP 100 Gain (V/V) 7 OPA2227-EP SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) At TA = 25C, RL = 10 k, VS = 15 V (unless otherwise noted). MAXIMUM OUTPUT VOLTAGE vs FREQUENCY V+ 14 (V+) -1V 13 (V+) -2V 12 -40C 125C 85C 25C 11 10 -10 -55C 85C -11 (V+) -3V -55C 125C -12 (V-) +3V -40C 25C -13 30 VS = 15V 25 Output Voltage (Vp-p) Output Voltage Swing (V) OUTPUT VOLTAGE SWING vs OUTPUT CURRENT 15 20 15 (V-) +2V -14 VS = 5V 10 5 (V-) +1V -15 V- 0 10 20 30 40 50 0 60 1k Output Current (mA) 10k 100k 1M 10M Frequency (Hz) SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE LARGE-SIGNAL STEP RESPONSE G = -1, CL = 1500pF 70 Gain = +10 50 40 2V/div Overshoot (%) 60 30 20 Gain = -10 Gain = -1 Gain = +1 10 0 1 10 100 1k 10k 100k 5s/div Load Capacitance (pF) SMALL-SIGNAL STEP RESPONSE G = +1, CL = 5pF 25mV/div 25mV/div SMALL-SIGNAL STEP RESPONSE G = +1, CL = 1000pF 400ns/div 8 400ns/div Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP OPA2227-EP www.ti.com SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 APPLICATION INFORMATION Basic Connection The OPA2227 is a precision operational amplifier with very low noise. It is unity-gain stable with a slew rate of 2.3 V/s and 8-MHz bandwidth. Applications with noisy or high impedance power supplies may require decoupling capacitors close to the device pins. In most cases, 0.1-F capacitors are adequate. Offset Voltage and Drift The OPA2227 has very low offset voltage and drift. To achieve highest dc precision, circuit layout and mechanical conditions should be optimized. Connections of dissimilar metals can generate thermal potentials at the op amp inputs which can degrade the offset voltage and drift. These thermocouple effects can exceed the inherent drift of the amplifier and ultimately degrade its performance. The thermal potentials can be made to cancel by assuring that they are equal at both input terminals. In addition: * Keep thermal mass of the connections made to the two input terminals similar. * Locate heat sources as far as possible from the critical input circuitry. * Shield operational amplifier and input circuitry from air currents such as those created by cooling fans. Operating Voltage OPA2227 operational amplifier operates from 2.5-V to 18-V supplies with excellent performance. Unlike most operational amplifiers which are specified at only one supply voltage, the OPA2227 is specified for real-world applications; a single set of specifications applies over the 5-V to 15-V supply range. Specifications are assured for applications between 5-V and 15-V power supplies. Some applications do not require equal positive and negative output voltage swing. Power supply voltages do not need to be equal. The OPA2227 can operate with as little as 5 V between the supplies and with up to 36 V between the supplies. For example, the positive supply could be set to 25 V with the negative supply at -5 V or vice-versa. In addition, key parameters are assured over the specified temperature range, -55C to 125C. Parameters which vary significantly with operating voltage or temperature are shown in the Typical Performance Curves. Offset Voltage Adjustment The OPA2227 is laser-trimmed for very low offset and drift so most applications will not require external adjustment. Input Protection Back-to-back diodes (see Figure 2) are used for input protection on the OPA2227. Exceeding the turn-on threshold of these diodes, as in a pulse condition, can cause current to flow through the input protection diodes due to the amplifier's finite slew rate. Without external current-limiting resistors, the input devices can be destroyed. Sources of high input current can cause subtle damage to the amplifier. Although the unit may still be functional, important parameters such as input offset voltage, drift, and noise may shift. RF 500 - OPA2227 Input Output + Figure 2. Pulsed Operation When using the OPA2227 as a unity-gain buffer (follower), the input current should be limited to 20 mA. This can be accomplished by inserting a feedback resistor or a resistor in series with the source. Sufficient resistor size can be calculated: RX = VS/20 mA - RSOURCE (1) Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP 9 OPA2227-EP SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 www.ti.com where RX is either in series with the source or inserted in the feedback path. For example, for a 10-V pulse (VS = 10 V), total loop resistance must be 500 . If the source impedance is large enough to sufficiently limit the current on its own, no additional resistors are needed. The size of any external resistors must be carefully chosen since they will increase noise. See the Noise Performance section of this data sheet for further information on noise calculation. Figure 2 shows an example implementing a current limiting feedback resistor. Input Bias Current Cancellation The input bias current of the OPA2227 is internally compensated with an equal and opposite cancellation current. The resulting input bias current is the difference between with input bias current and the cancellation current. The residual input bias current can be positive or negative. When the bias current is cancelled in this manner, the input bias current and input offset current are approximately equal. A resistor added to cancel the effect of the input bias current (as shown in Figure 3) may actually increase offset and noise and is therefore not recommended. Conventional Op Amp Configuration R2 R1 Op Amp RB = R2 || R1 External Cancellation Resistor Figure 3. Input Bias Current Cancellation Noise Performance Figure 4 shows total circuit noise for varying source impedances with the operational amplifier in a unity-gain configuration (no feedback resistor network, therefore no additional noise contributions). Two different operational amplifiers are shown with total circuit noise calculated. The OPA2227 has very low voltage noise, making it ideal for low source impedances (less than 20 k). A similar precision operational amplifier, the OPA277, has somewhat higher voltage noise but lower current noise. It provides excellent noise performance at moderate source impedance (10 k to 100 k). Above 100 k, a FET-input op amp such as the OPA132 (very low current noise) may provide improved performance. The equation is shown for the calculation of the total circuit noise. Note that en = voltage noise, in = current noise, RS = source impedance, k = Boltzmann's constant = 1.38 x 10-23 J/K and T is temperature in K. For more details on calculating noise, see "Basic Noise Calculations." VOLTAGE NOISE SPECTRAL DENSITY vs SOURCE RESISTANCE Votlage Noise Spectral Density, E 0 Typical at 1k (V/Hz) 1.00+03 EO OPA2227 RS 1.00E+02 Resistor Noise OPA2227 1.00E+01 Resistor Noise EO2 = en2 + (in RS)2 + 4kTRS 1.00E+00 100 1k 10k 100k 1M Source Resistance, RS () Figure 4. Noise Performance of the OPA2227 in Unity-Gain Buffer Configuration 10 Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP OPA2227-EP www.ti.com SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 Basic Noise Calculations Design of low noise operational amplifier circuits requires careful consideration of a variety of possible noise contributors: noise from the signal source, noise generated in the operational amplifier, and noise from the feedback network resistors. The total noise of the circuit is the root-sum-square combination of all noise components. The resistive portion of the source impedance produces thermal noise proportional to the square root of the resistance. This function is shown plotted in Figure 4. Since the source impedance is usually fixed, select the operational amplifier and the feedback resistors to minimize their contribution to the total noise. Figure 4 shows total noise for varying source impedances with the operational amplifier in a unity-gain configuration (no feedback resistor network and therefore no additional noise contributions). The operational amplifier itself contributes both a voltage noise component and a current noise component. The voltage noise is commonly modeled as a time-varying component of the offset voltage. The current noise is modeled as the timevarying component of the input bias current and reacts with the source resistance to create a voltage component of noise. Consequently, the lowest noise operational amplifier for a given application depends on the source impedance. For low source impedance, current noise is negligible and voltage noise generally dominates. For high source impedance, current noise may dominate. Figure 5 shows both inverting and noninverting operational amplifier circuit configurations with gain. In circuit configurations with gain, the feedback network resistors also contribute noise. The current noise of the operational amplifier reacts with the feedback resistors to create additional noise components. The feedback resistor values can generally be chosen to make these noise sources negligible. The equations for total noise are shown for both configurations. Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP 11 OPA2227-EP SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 www.ti.com Noise in Noninverting Gain Configuration R2 R1 EO RS VS Noise in Inverting Gain Configuration R2 R1 EO RS VS For op amps at 1kHz, en = 3nV/Hz and in = 0.4pA/Hz. Figure 5. Noise Calculation in Gain Configurations 12 Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP OPA2227-EP www.ti.com SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 Figure 6 shows the 0.1-Hz to 10-Hz bandpass filter used to test the noise of the OPA2227. The filter circuit was designed using Texas Instruments' FilterPro software (available at www.ti.com). Figure 7 shows the configuration of the OPA2227 for noise testing. R1 2M R2 2M R8 402k R11 178k R3 1k R4 9.09k C4 22nF C6 10nF R6 40.2k C1 1F C2 1F U1 C3 0.47F (OPA2227) Input from Device Under Test R7 97.6k R9 178k 2 6 1 U2 3 R10 226k C5 0.47F (OPA2227) 5 U2 7 VOUT (OPA2227) R5 634k Figure 6. 0.1-Hz to 10-Hz Bandpass Filter Used to Test Wideband Noise of the OPA2227 22pF 100k 10 2 3 OPA2227 1 VOUT Device Under Test Figure 7. Noise Test Circuit Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP 13 OPA2227-EP SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 www.ti.com 1.1k 1.43k 2.2nF dc Gain = 1 330pF 1.1k 1.65k VIN 2 OPA2227 33nF 1.43k 1 1.91k 6 3 OPA2227 68nF 7 5 2.21k VOUT 10nF fN = 13.86kHz fN = 20.33kHz Q = 1.186 Q = 4.519 f = 7.2kHz Figure 8. Three-Pole, 20-kHz Low Pass, 0.5-dB Chebyshev Filter 0.1F 100 100k 2 3 Dexter 1M Thermopile Detector OPA2227 1 Output NOTE: Use metal film resistors and plastic film capacitor. Circuit must be well shielded to achieve low noise. Responsivity 2.5 x 104V/W Output Noise 30Vrms, 0.1Hz to 10Hz Figure 9. Long-Wavelength Infrared Detector Amplifier 14 Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP OPA2227-EP www.ti.com SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 +15V 0.1F 1k 1k Audio In 1/2 OPA2227 200 200 To Headphone 1/2 OPA2227 This application uses two op amps in parallel for higher output current drive. 0.1F -15V Figure 10. Headphone Amplifier Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP 15 OPA2227-EP SBOS594A - MARCH 2012 - REVISED NOVEMBER 2012 www.ti.com Bass Tone Control R2 50k R1 7.5k 3 1 CW 2 R3 7.5k R10 100k Midrange Tone Control C1 940pF R5 50k R4 2.7k 3 VIN CW 1 2 R6 2.7k C2 0.0047F Treble Tone Control R7 7.5k R8 50k 3 CW 1 2 R9 7.5k C3 680pF R11 100k 2 3 OPA2227 1 VOUT Figure 11. Three-Band ActiveTone Control (Bass, Midrange and Treble) 16 Submit Documentation Feedback Copyright (c) 2012, Texas Instruments Incorporated Product Folder Links: OPA2227-EP PACKAGE OPTION ADDENDUM www.ti.com 24-Jan-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Qty Drawing Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Top-Side Markings (3) (4) OPA2227MDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -55 to 125 2227EP V62/12610-01XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -55 to 125 2227EP (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Only one of markings shown within the brackets will appear on the physical device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF OPA2227-EP : * Catalog: OPA2227 Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 24-Jan-2013 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 25-Feb-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device OPA2227MDREP Package Package Pins Type Drawing SOIC D 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.4 B0 (mm) K0 (mm) P1 (mm) 5.2 2.1 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 25-Feb-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA2227MDREP SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: OPA2227MDREP V62/12610-01XE