PCA9620 60 x 8 LCD high-drive segment driver for automotive and industrial Rev. 3 -- 3 July 2013 Product data sheet 1. General description The PCA9620 is a peripheral device which interfaces to almost any Liquid Crystal Display (LCD)1 with low multiplex rates. It generates the drive signals for any static or multiplexed LCD containing up to eight backplanes, 60 segments, and up to 480 elements. The PCA9620 is compatible with most microprocessors or microcontrollers and communicates via a two-line bidirectional I2C-bus. Communication overheads are minimized using a display RAM with auto-incremented addressing and display memory switching. The PCA9620 features an internal charge pump with internal capacitors for on-chip generation of the LCD driving voltages 2. Features and benefits 1. AEC Q100 grade 2 compliant for automotive applications Low power consumption Extended operating temperature range from 40 C to +105 C 60 segments and 8 backplanes allowing to drive: up to 60 7-segment alphanumeric characters up to 30 14-segment alphanumeric characters any graphics of up to 480 elements 480-bit RAM for display data storage Selectable backplane drive configuration: static, 2, 4, 6, or 8 backplane multiplexing Programmable internal charge pump for on-chip LCD voltage generation up to 3 VDD2 400 kHz I2C-bus interface Selectable linear temperature compensation of VLCD Selectable display bias configuration Wide range for digital and analog power supply: from 2.5 V to 5.5 V Wide LCD supply range: from 2.5 V for low threshold LCDs and up to 9.0 V for high threshold (automobile) twisted nematic LCDs Display memory bank switching in static, duplex, and quadruplex drive modes Programmable frame frequency in steps of 10 Hz in the range of 60 Hz to 300 Hz; factory calibrated with a tolerance of 15 % covering the whole temperature and voltage range Selectable inversion scheme for LCD driving waveforms: frame or line inversion Integrated temperature sensor with temperature readout On chip calibration of internal oscillator frequency and VLCD The definition of the abbreviations and acronyms used in this data sheet can be found in Section 20 on page 73. PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 3. Applications Automotive Instrument cluster Car radio Climate control units Industrial Machine control systems Measuring equipment Signage Information boards Panels 4. Ordering information Table 1. Ordering information Type number Package Name Description Version PCA9620H LQFP80 plastic low profile quad flat package; 80 leads; body 12 12 1.4 mm SOT315-1 PCA9620U bare die 80 bonding pads PCA9620U 4.1 Ordering options Table 2. Ordering options Product type number Sales item (12NC) Orderable part number IC revision Delivery form PCA9620H/Q900/1 935291899518 PCA9620H/Q900/1,51 1 tape and reel, 13 inch, dry pack PCA9620U/5GA/Q1 935295801015 PCA9620U/5GA/Q1,01 1 wafer, unsawn 5. Marking Table 3. Marking codes Type number PCA9620 Product data sheet Marking code PCA9620H PCA9620H/Q900 PCA9620U PC9620-1 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 2 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 6. Block diagram VLCD BP0 to BP7 S0 to S59 60 VDD2 BACKPLANE OUTPUTS DISPLAY SEGMENT OUTPUTS LCD VOLTAGE SELECTOR CHARGE PUMP(1) (VOLTAGE MULTIPLIER) DISPLAY REGISTER DISPLAY CONTROL OUTPUT BANK SELECT LCD BIAS GENERATOR VSS DISPLAY RAM CLK TEMPERATURE SENSOR CLOCK SELECT AND TIMING OSCILLATOR POWER-ON RESET SCL PCA9620 COMMAND DECODER WRITE DATA CONTROL DATA POINTER, AUTO INCREMENT I2C-BUS CONTROLLER SDA 013aaa246 A0 A1 VDD1 T1 T2 T3 (1) The charge pump can generate a maximum output voltage of 3 VDD2. Fig 1. Block diagram of PCA9620 PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 3 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 7. Pinning information 61 S0 62 S1 63 S2 64 S3 65 S4 66 S5 67 S6 68 S7 69 S8 70 S9 71 S10 72 S11 73 S12 74 S13 75 S14 76 S15 77 S16 78 S17 79 S18 80 S19 7.1 Pinning S20 1 60 SDA S21 2 59 SCL S22 3 58 A1 S23 4 57 A0 S24 5 56 CLK S25 6 55 T3 S26 7 54 T2 S27 8 53 T1 S28 9 52 VSS S29 10 51 VDD1 PCA9620H S30 11 50 VDD2 S59 40 S58 39 S57 38 S56 37 S55 36 S54 35 S53 34 S52 33 S51 32 S50 31 S49 30 41 BP0 S48 29 42 BP1 S39 20 S47 28 43 BP2 S38 19 S46 27 44 BP3 S37 18 S45 26 45 BP4 S36 17 S44 25 46 BP5 S35 16 S43 24 47 BP6 S34 15 S42 23 48 BP7 S33 14 S41 22 49 VLCD S32 13 S40 21 S31 12 013aaa244 Top view. For mechanical details, see Figure 58 on page 63. Fig 2. Pin configuration for LQFP80 (PCA9620H) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 4 of 81 PCA9620 NXP Semiconductors S19 S18 S17 S16 S15 S14 S13 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 x 8 LCD high-drive segment driver for automotive and industrial S20 1 60 SDA S21 2 59 SCL S22 3 58 A1 S23 4 57 A0 S24 5 56 CLK S25 6 55 T3 S26 7 54 T2 S27 8 53 T1 S28 9 52 VSS S29 10 51 VDD1 S30 11 50 VDD2 S31 12 49 VLCD S32 13 48 BP7 S33 14 47 BP6 S34 15 46 BP5 S35 16 45 BP4 S36 17 44 BP3 S37 18 43 BP2 S38 19 42 BP1 S39 20 41 BP0 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 S40 S41 S42 S43 S44 S45 S46 S47 S48 S49 S50 S51 S52 S53 S54 S55 S56 S57 S58 S59 PCA9620U 013aaa510 Viewed from active side. For mechanical details, see Figure 59 on page 64. Fig 3. Pin configuration for PCA9620U (bare die) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 5 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 7.2 Pin description Table 4. Pin Type Description S0 to S59 61 to 80 and 1 to 40 output LCD segment BP0 to BP7 41 to 48 output LCD backplane VLCD 49 supply/output[1] LCD supply voltage VDD2 50 supply supply voltage 2 (charge pump) VDD1 51 supply supply voltage 1 (analog and digital) VSS 52 supply ground supply voltage T1 to T3 53 to 55 input test pins; must be tied to VSS in applications CLK 56 input/output internal oscillator output, external oscillator input A0, A1 57, 58 input I2C-bus slave address selection bit SCL 59 input I2C-bus serial clock SDA 60 input/output I2C-bus serial data [1] PCA9620 Product data sheet Pin description Symbol When the internal VLCD generation is used, this pin drives the VLCD voltage. In this case pin VLCD is an output. When the external supply is requested, then pin VLCD is an input and VLCD can be supplied to it. In this case, the internal charge pump must be disabled (see Table 9 on page 9). All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 6 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8. Functional description The PCA9620 is a versatile peripheral device designed to interface any microprocessor or microcontroller to a wide variety of LCDs. It can directly drive any static or multiplexed LCD containing up to 480 elements. 8.1 Commands of PCA9620 The PCA9620 is controlled by 22 commands, which are defined in Table 5. Any other combinations of operation code bits that are not mentioned in this document may lead to undesired operation modes of PCA9620. Table 5. Commands of PCA9620 Command name initialize Bits Reference 7 6 5 4 3 2 1 0 0 0 1 1 1 0 1 0 Section 8.1.1 OTP-refresh 1 1 0 1 0 0 0 0 Section 8.1.2 oscillator-ctrl 1 1 0 0 1 1 COE OSC Section 8.1.3 charge-pump-ctrl 1 1 0 0 0 0 CPE CPC Section 8.1.4 temp-msr-ctrl 1 1 0 0 1 0 TCE TME Section 8.1.5 temp-comp-SLA 0 0 0 1 1 SLA[2:0] temp-comp-SLB 0 0 1 0 0 SLB[2:0] temp-comp-SLC 0 0 1 0 1 SLC[2:0] temp-comp-SLD 0 0 1 1 0 SLD[2:0] set-VPR-MSB 0 1 0 0 VPR[7:4] set-VPR-LSB 0 1 0 1 VPR[3:0] display-enable 0 0 1 1 1 0 set-MUX-mode 0 0 0 0 0 M[2:0] set-bias-mode 1 1 0 0 0 1 load-data-pointer 1 0 P[5:0] frame-frequency 0 1 1 F[4:0] input-bank-select 0 0 0 0 1 IB[2:0] output-bank-select 0 0 0 1 0 OB[2:0] write-RAM-data B[7:0] Section 8.1.13 temp-read TD[7:0] Section 8.1.14, Section 8.4.7 invmode_CPF_ctrl 1 1 0 1 0 1 LF CPF Section 8.1.15 temp-filter 1 1 0 1 0 0 1 TFE Section 8.1.16 Table 30 Section 8.1.6 0 E Section 8.1.7 Section 8.1.8 B[1:0] Section 8.1.9 Section 8.1.10 Section 8.1.11 Section 8.1.12.1 8.1.1 Command: initialize This command generates a chip-wide reset which resets all command values to their default values (see Table 26 on page 17). It must be sent to the PCA9620 after power-on. After this command is sent, it is possible to send additional commands without the need to re-initialize the interface. Reset takes 100 ns to complete. For further information, see Section 8.3 on page 16. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 7 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 6. Initialize - initialize command bit description Bit Symbol Value Description 7 to 0 - 00111010 fixed value 8.1.2 Command: OTP-refresh In order to achieve the specified accuracy of VLCD, the frame frequency, and the temperature measurement, each IC is calibrated during production and testing of the device. This calibration is performed on EPROM cells called One Time Programmable (OTP) cells. These cells are read by the device at power-on, after a reset, and every time when the initialize command or the OTP-refresh command is sent. This command will take approximately 10 ms to finish. Table 7. OTP-refresh - OTP-refresh command bit description Bit Symbol Value Description 7 to 0 - 11010000 fixed value 8.1.3 Command: oscillator-ctrl The oscillator-ctrl command switches between internal and external oscillator and enables or disables pin CLK. Table 8. Oscillator-ctrl - oscillator control command bit description For further information, see Section 8.5 on page 40. Bit Symbol Value Description 7 to 2 - 110011 fixed value 1 COE 0 [1] PCA9620 Product data sheet control pin CLK 0[1] clock signal not available on pin CLK; pin CLK is in 3-state and may be left floating 1 clock signal available on pin CLK OSC oscillator source 0[1] internal oscillator running 1 external oscillator used; pin CLK becomes an input Default value. All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 8 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.1.4 Command: charge-pump-ctrl The charge-pump-ctrl command enables or disables the internal VLCD generation and controls the charge pump voltage multiplier setting. Table 9. Charge-pump-ctrl - charge pump control command bit description Bit Symbol Value Description 7 to 2 - 110000 fixed value 1 CPE 0 [1] charge pump switch 0[1] charge pump disabled; no internal VLCD generation; external supply of VLCD 1 charge pump enabled CPC charge pump voltage multiplier setting 0[1] VLCD = 2 VDD2 1 VLCD = 3 VDD2 Default value. 8.1.5 Command: temp-msr-ctrl The temp-msr-ctrl command enables or disables the temperature measurement block and the temperature compensation of VLCD. Table 10. Temp-msr-ctrl - temperature measurement control command bit description For further information, see Section 8.4.8 on page 38. Bit Symbol Value Description 7 to 2 - 110010 fixed value 1 TCE temperature compensation switch 0 no temperature compensation of VLCD possible 1[1] 0 temperature compensation of VLCD possible TME temperature measurement switch 0 temperature measurement disabled; 1[1] temperature measurement enabled; no temperature readout possible temperature readout possible [1] Default value. 8.1.6 Command: set-VPR-MSB and set-VPR-LSB With these two instructions, it is possible to set the target VLCD voltage for the internal charge pump, see Section 8.4.3 on page 33. Table 11. Bit Symbol Value Description 7 to 4 - 0100 fixed value VPR[7:4] 0000[1] 3 to 0 [1] PCA9620 Product data sheet Set-VPR-MSB - set VPR MSB command bit description to 1111 the four most significant bits of VPR[7:0] Default value. All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 9 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 12. Set-VPR-LSB - set VPR LSB command bit description Bit Symbol Value Description 7 to 4 - 0101 fixed value VPR[3:0] 0000[1] 3 to 0 [1] to 1111 the four least significant bits of VPR[7:0] Default value. 8.1.7 Command: display-enable Table 13. Display-enable - display enable command bit description Bit Symbol Value Description 7 to 1 - 0011100 fixed value 0 E 0[1] display disabled; backplane and segment outputs are internally connected to VSS 1 display enabled [1] Default value. 8.1.8 Command: set-MUX-mode Table 14. Set-MUX-mode - set multiplex drive mode command bit description Bit Symbol Value 7 to 3 - 00000 fixed value 2 to 0 M[2:0] 000[1], 011, 110, 111 1:8 multiplex drive mode: 8 backplanes 001 static drive mode: 1 backplane 010 1:2 multiplex drive mode: 2 backplanes 100 1:4 multiplex drive mode: 4 backplanes 101 1:6 multiplex drive mode: 6 backplanes [1] Description Default value. 8.1.9 Command: set-bias-mode Table 15. Set-bias-mode - set bias mode command bit description Bit Symbol Value Description 7 to 2 - 110001 fixed value B[1:0] 00[1], 1 4 bias 11 1 3 bias 10 1 2 bias 1 to 0 [1] 01 Default value. 8.1.10 Command: load-data-pointer The load-data-pointer command defines one of the 60 display RAM addresses where the following display data will be sent to. For further information, see Section 8.9.1 on page 43. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 10 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 16. Load-data-pointer - load data pointer command bit description Bit Symbol Value Description 7 to 6 - 10 fixed value 5 to 0 P[5:0] 000000 to 111111 6-bit binary value of 0 to 59 8.1.11 Command: frame-frequency With the frame-frequency command, the frame frequency and the output clock frequency can be configured. Table 17. Bit Symbol Value Description 7 to 5 - 011 fixed value 4 to 0 F[4:0] see Table 18 nominal frame frequency (Hz) Table 18. Product data sheet Frame frequency values F[4:0] Nominal frame frequency, ffr (Hz)[1] Resultant oscillator frequency, fosc (Hz) Duty cycle (%)[2] 00000 60 2880 20 : 80 00001 70 3360 7 : 93 00010 80 3840 47 : 53 00011 91 4368 40 : 60 00100 100 4800 33 : 67 00101 109 5232 27 : 73 00110 120 5760 20 : 80 00111 129.7 6226 13 : 87 01000 141.2 6778 5 : 95 01001 150 7200 50 : 50 01010 160 7680 47 : 53 01011 171.4 8227 43 : 57 01100 177.8 8534 41 : 59 01101 192 9216 36 : 64 01110[3] 200 9600 33 : 67 01111 208.7 10018 30 : 70 10000 218.2 10474 27 : 73 10001 228.6 10973 23 : 77 10010 240 11520 20 : 80 10011 252.6 12125 16 : 84 10100, 10101 266.7 12802 10 : 90 10110, 10111 282.4 13555 5 : 95 11000 to 11111 300 14400 50 : 50 [1] PCA9620 Frame frequency - frame frequency and output clock frequency command bit description Nominal frame frequency calculated for the default clock frequency of 9600 Hz. [2] Duty cycle definition: % HIGH-level time : % LOW-level time. [3] Default value. All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 11 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.1.12 Bank select commands For multiplex drive modes 1:4, 1:2 and static drive mode, it is possible to write data to one area of the RAM while displaying from another. These areas are named as RAM banks. Input and output banks can be set independently from one another with the input-bank-select and the output-bank-select command. For further information, see Section 8.9.2 on page 48. 8.1.12.1 Command: input-bank-select Input-bank-select - input bank select command bit description[1] Table 19. 8.1.12.2 Bit Symbol Value Description 7 to 3 - 00001 fixed value 2 to 0 IB[2:0] Product data sheet static drive mode 1:2 drive mode 1:4 drive mode 000[2] bank 0: RAM-row 0 001 bank 1: RAM-row 1 bank 0: RAM-rows 0 and 1 bank 0: RAM-rows 0, 1, 2, and 3 010 bank 2: RAM-row 2 011 bank 3: RAM-row 3 100 bank 4: RAM-row 4 101 bank 5: RAM-row 5 110 bank 6: RAM-row 6 111 bank 7: RAM-row 7 [1] Not applicable for multiplex drive mode 1:6 and 1:8. [2] Default value. bank 2: RAM-rows 2 and 3 bank 4: RAM-rows 4 and 5 bank 4: RAM-rows 4, 5, 6, and 7 bank 6: RAM-rows 6 and 7 Command: output-bank-select Output-bank-select - output bank select command bit description[1] Table 20. PCA9620 selects RAM bank to write to Bit Symbol Value 7 to 3 - 00010 2 to 0 OB[2:0] Description fixed value selects RAM bank to read from to the LCD static drive mode 1:2 drive mode 1:4 drive mode 000[2] bank 0: RAM-row 0 001 bank 1: RAM-row 1 bank 0: RAM-rows 0 and 1 bank 0: RAM-rows 0, 1, 2, and 3 010 bank 2: RAM-row 2 011 bank 3: RAM-row 3 100 bank 4: RAM-row 4 101 bank 5: RAM-row 5 110 bank 6: RAM-row 6 111 bank 7: RAM-row 7 [1] Not applicable for multiplex drive mode 1:6 and 1:8. [2] Default value. bank 2: RAM-rows 2 and 3 bank 4: RAM-rows 4 and 5 bank 6: RAM-rows 6 and 7 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 bank 4: RAM-rows 4, 5, 6, and 7 (c) NXP B.V. 2013. All rights reserved. 12 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.1.13 Command: write-RAM-data The write-RAM-data command writes data byte-wise to the RAM. After Power-On Reset (POR) the RAM content is random and should be brought to a defined status by clearing it (setting it logic 0). Write-RAM-data - write RAM data command bit description[1] Table 21. Bit Symbol Value Description 7 to 0 B[7:0] 00000000 to 11111111 writing data byte-wise to RAM [1] For this command bit RS of the control byte has to be set logic 1 (see Table 34 on page 54). More information about the display RAM can be found in Section 8.9 on page 42. 8.1.14 Command: temp-read The temp-read command allows reading out the temperature values measured by the internal temperature sensor. Table 22. Temp-read - temperature readout command bit description[1] For further information, see Table 10 on page 9 and Section 8.4.7 on page 37. Bit Symbol Value Description 7 to 0 TD[7:0] 00000000 to 11111111 readout representing the digital temperature [1] For this command bit R/W of the I2C-bus slave address byte has to be set logic 1 (see Table 33 on page 53). 8.1.15 Command: invmode_CPF_ctrl The invmode_CPF_ctrl command allows changing the drive scheme inversion mode and the charge pump frequency. The waveforms used to drive LCD displays inherently produce a DC voltage across the display cell. The PCA9620 compensates for the DC voltage by inverting the waveforms on alternate frames or alternate lines. The choice of compensation method is determined with the LF bit. Table 23. Bit Symbol Value Description 7 to 2 - 110101 fixed value 1 LF 0 [1] PCA9620 Product data sheet Invmode_CPF_ctrl - inversion mode and charge pump frequency prescaler command bit description set inversion mode 0[1] line inversion mode 1 frame inversion mode CPF set charge pump oscillator frequency 0[1] fosc(cp) ~ 1 MHz 1 fosc(cp) ~ 500 kHz Default value. All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 13 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial In frame inversion mode, the DC value is compensated across two frames and not within one frame. Changing the inversion mode to frame inversion reduces the power consumption, therefore it is useful when power consumption is a key point in the application. Frame inversion may not be suitable for all applications. The RMS voltage across a segment is better defined, however since the switching frequency is reduced there is possibility for flicker to occur. The waveforms of Figure 16 on page 25 to Figure 22 on page 31 are showing line inversion mode. Figure 23 on page 32 shows one example of frame inversion. 8.1.16 Command: temp-filter Table 24. Temp-filter - digital temperature filter command bit description Bit Symbol Value Description 7 to 1 - 1101001 fixed value 0 TFE [1] digital temperature filter switch 0[1] digital temperature filter disabled; the unfiltered digital value of TD[7:0] is immediately available for the readout and VLCD compensation, see Section 8.4.7 on page 37 1 digital temperature filter enabled Default value. 8.2 Possible display configurations The PCA9620 is a versatile peripheral device designed to interface between any microcontroller to a wide variety of LCD segment or dot matrix displays (see Figure 4). It can directly drive any static or multiplexed LCD containing up to eight backplanes and up to 60 segments. The display configurations possible with the PCA9620 depend on the number of active backplane outputs required. A selection of possible display configurations is given in Table 25. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 14 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial dot matrix 7-segment with dot 14-segment with dot and accent 013aaa312 Fig 4. Example of displays suitable for PCA9620 Table 25. Selection of possible display configurations Number of Backplanes Icons Digits/Characters 7-segment 14-segment Dot matrix/ Elements 8 480 60 30 480 dots (8 60) 6 320 45 22 360 dots (6 60) 4 240 30 15 240 dots (4 60) 2 120 15 7 120 dots (2 60) 1 60 7 3 60 dots (1 60) All of the display configurations in Table 25 can be implemented in the typical systems shown in Figure 5 (internal VLCD) and in Figure 6 (external VLCD). VDD2 VDD1 R tr 2Cb VDD1 HOST PROCESSOR/ MICROCONTROLLER VDD2 VLCD 60 segment drives SDA LCD PANEL (up to 480 elements) SCL PCA9620 8 backplanes A0 A1 CLK VSS 013aaa247 n.c. VSS VDD1 from 2.5 V to 5.5 V and VDD2 from 2.5 V to 5.5 V. Fig 5. PCA9620 Product data sheet Typical system configuration when using the internal VLCD generation All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 15 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial VLCD VDD1 R tr 2Cb VDD1 VDD2 VLCD 60 segment drives SDA HOST PROCESSOR/ MICROCONTROLLER LCD PANEL (up to 480 elements) SCL PCA9620 8 backplanes A0 A1 CLK VSS 013aaa248 n.c. VSS VDD1 from 2.5 V to 5.5 V, VDD2 from 2.5 V to 5.5 V and VLCD from 2.5 V to 9.0 V. Fig 6. Typical system configuration when using an external VLCD The host microcontroller maintains the two line I2C-bus communication channel with the PCA9620. The appropriate biasing voltages for the multiplexed LCD waveforms are generated internally. The only other connections required to complete the system are the power supplies (VDD1, VDD2, VSS, VLCD), the external capacitors, and the LCD panel selected for the application. The minimum recommended values for external capacitors on VDD1, VDD2, and VLCD are nominal 100 nF. When using bigger capacitors, especially on the VLCD, the generated ripple will be consequently smaller. However it will take longer for the internal charge pump to reach the target VLCD voltage first. If VDD1 and VDD2 are connected externally, the capacitors on VDD1 and VDD2 can be replaced by a single capacitor with a minimum value of 200 nF. Remark: In the case of insufficient decoupling, ripple of VDD1 and VDD2 will create additional VLCD ripple. The ripple on VLCD can be reduced by making the VSS connection as low-ohmic as possible. Excessive ripple on VLCD may cause flicker on the display. 8.3 Start-up and shut-down 8.3.1 Power-On Reset (POR) At power-on, the PCA9620 resets to starting conditions as follows: 1. All backplane outputs are set to VSS. 2. All segment outputs are set to VSS. 3. Selected drive mode is: 1:8 with 14 bias. 4. Input and output bank selectors are reset. 5. The I2C-bus interface is initialized. 6. The data pointer is cleared (set logic 0). 7. The Internal oscillator is running; no clock signal is available on pin CLK; pin CLK is in 3-state. 8. Temperature measurement is enabled. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 16 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 9. Temperature filter is disabled. 10. The internal VLCD voltage generation is disabled. The charge pump is switched off. 11. The VLCD temperature compensation is enabled. 12. The display is disabled. Remark: Do not transfer data on the I2C-bus for at least 1 ms after a power-on to allow the reset action to complete. The first command sent to the device after the power-on event must be the initialize command (see Section 8.1.1 on page 7). After Power-On Reset (POR) and before enabling the display, the RAM content should be brought to a defined status * by clearing it (setting it all logic 0) or * by writing meaningful content (for example, a graphic) otherwise unwanted display artifacts may appear on the display. Table 26. Reset states Bits labeled - are undefined at power-on. Command name PCA9620 Product data sheet Bits 7 6 5 4 3 2 1 0 initialize 0 0 1 1 1 0 1 0 OTP-refresh 1 1 0 1 0 0 0 0 oscillator-ctrl 1 1 0 0 1 1 0 0 charge-pump-ctrl 1 1 0 0 0 0 0 0 temp-msr-ctrl 1 1 0 0 1 0 1 1 temp-comp-SLA 0 0 0 1 1 0 0 0 temp-comp-SLB 0 0 1 0 0 0 0 0 temp-comp-SLC 0 0 1 0 1 0 0 0 temp-comp-SLD 0 0 1 1 0 0 0 0 set-VPR-MSB 0 1 0 0 0 0 0 0 set-VPR-LSB 0 1 0 1 0 0 0 0 display-enable 0 0 1 1 1 0 0 0 set-MUX-mode 0 0 0 0 0 0 0 0 set-bias-mode 1 1 0 0 0 1 0 0 load-data-pointer 1 0 0 0 0 0 0 0 frame-frequency 0 1 1 0 1 1 1 0 input-bank-select 0 0 0 0 1 0 0 0 output-bank-select 0 0 0 1 0 0 0 0 write-RAM-data - - - - - - - - temp-read 0 1 0 0 0 0 0 0 invmode_CPF_ctrl 1 1 0 1 0 1 0 0 temp-filter 1 1 0 1 0 0 1 0 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 17 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.3.2 Recommended start-up sequences This chapter describes how to proceed with the initialization of the chip in different application modes. START Power-on VDD1 and VDD2 at the same time Set VPR register to desired VLCD value Set multiplication factor for charge pump and enable it Wait 1 ms Initialize command Initiate an OTP-refresh Wait till VLCD reaches programmed value(1) Write RAM content to be displayed and enable the display(2) STOP 013aaa249 (1) This time depends on the external capacitor on pin VLCD. For a capacitor of 100 nF a delay of 5 ms to 15 ms is expected. When using the internal VLCD generation, the display must not be enabled before the generation of VLCD with the internal charge pump is completed. Otherwise unwanted display artifacts may appear on the display. (2) RAM data may be written before or during the ramp-up of VLCD. Fig 7. PCA9620 Product data sheet Recommended start-up sequence when using the internal charge pump and the internal clock signal All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 18 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial START Initiate an OTP-refresh Power-on VDD1, VDD2, and VLCD at the same time Write RAM content to be displayed and enable the display Wait 1 ms STOP Initialize command 013aaa250 Fig 8. Recommended start-up sequence when using an external supplied VLCD and the internal clock signal START Power-on VDD1 and VDD2 at the same time Apply external clock signal to pin CLK; set OSC bit logic 1(1) Wait till VLCD reaches programmed value(2) (1) Wait 1 ms Set VPR register to desired VLCD value Initialize command Initiate an OTP-refresh Set multiplication factor for charge pump and enable it Write RAM content to be displayed and enable the display(3) STOP 013aaa251 (1) The external clock signal can be applied after the generation of the VLCD voltage as well. (2) This time depends on the external capacitor on pin VLCD. For a capacitor of 100 nF a delay of 5 ms to 15 ms is expected. (3) RAM data may be written before or during the ramp-up of VLCD. Fig 9. PCA9620 Product data sheet Recommended start-up sequence when using the internal charge pump and an external clock signal All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 19 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial START Power-on VDD1, VDD2, and VLCD at the same time Apply external clock signal to pin CLK; set OSC bit logic 1 Wait 1 ms Write RAM content to be displayed and enable the display Initialize command STOP Initiate an OTP-refresh 013aaa252 Fig 10. Recommended start-up sequence when using an external supplied VLCD and an external clock signal 8.3.3 Recommended power-down sequences With the following sequences, the PCA9620 can be set to a state of minimum power consumption, called power-down mode. START Disable display by setting bit E logic 0 Stop generation of VLCD by setting bit CPE logic 0 Disable temperature measurement by setting bit TME logic 0 STOP 013aaa253 Fig 11. Recommended power-down sequence for minimum power-down current when using the internal charge pump and the internal clock signal PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 20 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial START Disable display by setting bit E logic 0 Disable temperature measurement by setting bit TME logic 0 STOP 013aaa254 Fig 12. Recommended power-down sequence when using an external supplied VLCD and the internal clock signal START Disable display by setting bit E logic 0 Stop generation of VLCD by setting bit CPE logic 0 Disable temperature measurement by setting bit TME logic 0 Bring pin CLK to 3-state by setting bit OSC and bit COE logic 0 External clock may be switched off STOP 013aaa255 Fig 13. Recommended power-down sequence when using the internal charge pump and an external clock signal PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 21 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial START Disable display by setting bit E logic 0 Disable temperature measurement by setting bit TME logic 0 Bring pin CLK to 3-state by setting bit OSC and bit COE logic 0 External clock may be switched off STOP 013aaa256 Fig 14. Recommended power-down sequence when using an external supplied VLCD and an external clock signal Remark: It is necessary to run the power-down sequence before removing the supplies. Depending on the application, care must be taken that no other signals are present at the chip input or output pins when removing the supplies (refer to Section 10 on page 55). Otherwise it may cause unwanted display artifacts. The PCA9620 will not be damaged by uncontrolled removal of supply voltages Remark: Static voltages across the liquid crystal display can build up when the external LCD supply voltage (VLCD) is on while the IC supply voltage (VDD1 or VDD2) is off, or vice versa. It may cause unwanted display artifacts. To avoid such artifacts, external VLCD, VDD1, and VDD2 must be applied or removed together. Remark: A clock signal must always be supplied to the device when the device is active; removing the clock may freeze the LCD in a DC state, which is not suitable for the liquid crystal. It is recommended to first disable the display and afterwards to remove the clock signal. 8.4 LCD voltage 8.4.1 LCD voltage selector The LCD voltage selector co-ordinates the multiplexing of the LCD in accordance with the selected LCD drive configuration. The operation of the voltage selector is controlled by the set-bias-mode command (see Table 15 on page 10) and the set-MUX-mode command (see Table 14 on page 10). Intermediate LCD biasing voltages are obtained from an internal voltage divider. The biasing configurations that apply to the preferred modes of operation, together with the biasing characteristics as functions of VLCD and the resulting discrimination ratios (D), are given in Table 27. Discrimination is a term which is defined as the ratio of the Von(RMS) and Voff(RMS) across a segment. It can be thought of as a measurement of contrast. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 22 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 27. LCD drive modes: summary of characteristics LCD drive mode Number of: Backplanes Levels LCD bias configuration V off RMS ----------------------V LCD V on RMS ---------------------V LCD VLCD[2] V on RMS D = ----------------------- [1] V off RMS static 1 2 static 0 1 Von(RMS) 1:2 multiplex 2 3 1 2 0.354 0.791 2.236 2.828 Voff(RMS) 1:2 multiplex 2 4 1 3 0.333 0.745 2.236 3.0 Voff(RMS) 5 1 4 0.395 0.729 1.845 2.529 Voff(RMS) 4 3 1 2 0.433 0.661 1.527 2.309 Voff(RMS) 4 4 1 3 0.333 0.577 1.732 3.0 Voff(RMS) 5 1 4 0.331 0.545 1.646 3.024 Voff(RMS) 3 1 2 0.456 0.612 1.341 2.191 Voff(RMS) 1:2 multiplex[3] 1:4 multiplex[3] 1:4 multiplex 1:4 multiplex[3] 1:6 multiplex[3] 2 4 6 1:6 multiplex 6 4 1 3 0.333 0.509 1.527 3.0 Voff(RMS) 1:6 multiplex 6 5 1 4 0.306 0.467 1.527 3.266 Voff(RMS) 3 1 2 0.467 0.586 1.254 2.138 Voff(RMS) 4 1 3 0.333 0.471 1.414 3.0 Voff(RMS) 5 1 4 0.293 0.424 1.447 3.411 Voff(RMS) 1:8 multiplex[3] 1:8 multiplex[3] 1:8 multiplex 8 8 8 [1] Determined from Equation 3. [2] Determined from Equation 2. [3] In these examples the discrimination factor and hence the contrast ratios are smaller. The advantage of these LCD drive modes is a power saving from a reduction of the LCD voltage VLCD. A practical value for VLCD is determined by equating Voff(RMS) with a defined LCD threshold voltage (Vth(off)), typically when the LCD exhibits approximately 10 % contrast. In the static drive mode a suitable choice is VLCD > 3Vth(off). 1 Bias is calculated by ------------- , where the values for a are 1+a a = 1 for 12 bias a = 2 for 13 bias a = 3 for 14 bias The RMS on-state voltage (Von(RMS)) for the LCD is calculated with Equation 1: V on RMS = V LCD a 2 + 2a + n -----------------------------2 n 1 + a (1) where VLCD is the resultant voltage at the LCD segment and where the values for n are n = 1 for static mode n = 2 for 1:2 multiplex n = 4 for 1:4 multiplex n = 6 for 1:6 multiplex n = 8 for 1:8 multiplex The RMS off-state voltage (Voff(RMS)) for the LCD is calculated with Equation 2: PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 23 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial V off RMS = V LCD a 2 - 2a + n -----------------------------2 n 1 + a (2) Discrimination is the ratio of Von(RMS) to Voff(RMS) and is determined from Equation 3: V on RMS --------------------- = V off RMS 2 a + 1 + n - 1 -------------------------------------------2 a - 1 + n - 1 (3) It should be noted that VLCD is sometimes referred as the LCD operating voltage. 8.4.1.1 Electro-optical performance Suitable values for Von(RMS) and Voff(RMS) are dependent on the LCD liquid used. The RMS voltage, at which a pixel will be switched on or off, determine the transmissibility of the pixel. For any given liquid, there are two threshold values defined. One point is at 10 % relative transmission (at Vth(off)) and the other at 90 % relative transmission (at Vth(on)), see Figure 15. For a good contrast performance, the following rules should be followed: V on RMS V th on (4) V off RMS V th off (5) Von(RMS) and Voff(RMS) are properties of the display driver and are affected by the selection of a, n (see Equation 1 to Equation 3) and the VLCD voltage. Vth(off) and Vth(on) are properties of the LCD liquid and can be provided by the module manufacturer. It is important to match the module properties to those of the driver in order to achieve optimum performance. 100 % Relative Transmission 90 % 10 % Vth(off) OFF SEGMENT Vth(on) GREY SEGMENT VRMS [V] ON SEGMENT 013aaa494 Fig 15. Electro-optical characteristic: relative transmission curve of the liquid PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 24 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.4.2 LCD drive mode waveforms 8.4.2.1 Static drive mode The static LCD drive mode is used when a single backplane is provided in the LCD. Tfr LCD segments VLCD BP0 VSS state 1 (on) VLCD state 2 (off) Sn VSS VLCD Sn+1 VSS (a) Waveforms at driver. VLCD state 1 0V -VLCD VLCD state 2 0V -VLCD (b) Resultant waveforms at LCD segment. 013aaa207 Vstate1(t) = VSn(t) VBP0(t). Vstate2(t) = V(Sn + 1)(t) VBP0(t). Von(RMS)(t) = VLCD. Voff(RMS)(t) = 0 V. Fig 16. Static drive mode waveforms (line inversion mode) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 25 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.4.2.2 1:2 Multiplex drive mode When two backplanes are provided in the LCD, the 1:2 multiplex mode applies. The PCA9620 allows the use of 12 bias or 13 bias in this mode as shown in Figure 17 and Figure 18. Tfr VLCD BP0 LCD segments VLCD/2 VSS state 1 VLCD BP1 state 2 VLCD/2 VSS VLCD Sn VSS VLCD Sn+1 VSS (a) Waveforms at driver. VLCD VLCD/2 state 1 0V -VLCD/2 -VLCD VLCD VLCD/2 state 2 0V -VLCD/2 -VLCD (b) Resultant waveforms at LCD segment. 013aaa208 Vstate1(t) = VSn(t) VBP0(t). Vstate2(t) = VSn(t) VBP1(t). Von(RMS)(t) = 0.791VLCD. Voff(RMS)(t) = 0.354VLCD. Fig 17. Waveforms for the 1:2 multiplex drive mode with 12 bias (line inversion mode) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 26 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Tfr BP0 BP1 Sn Sn+1 VLCD 2VLCD/3 LCD segments VLCD/3 VSS state 1 VLCD 2VLCD/3 state 2 VLCD/3 VSS VLCD 2VLCD/3 VLCD/3 VSS VLCD 2VLCD/3 VLCD/3 VSS (a) Waveforms at driver. VLCD 2VLCD/3 VLCD/3 state 1 0V -VLCD/3 -2VLCD/3 -VLCD VLCD 2VLCD/3 VLCD/3 state 2 0V -VLCD/3 -2VLCD/3 -VLCD (b) Resultant waveforms at LCD segment. 013aaa209 Vstate1(t) = VSn(t) VBP0(t). Vstate2(t) = VSn(t) VBP1(t). Von(RMS)(t) = 0.745VLCD. Voff(RMS)(t) = 0.333VLCD. Fig 18. Waveforms for the 1:2 multiplex drive mode with 13 bias (line inversion mode) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 27 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.4.2.3 1:4 Multiplex drive mode When four backplanes are provided in the LCD, the 1:4 multiplex drive mode applies, as shown in Figure 19. Tfr BP0 VLCD 2VLCD/3 VLCD/3 VSS BP1 VLCD 2VLCD/3 VLCD/3 VSS BP2 VLCD 2VLCD/3 VLCD/3 VSS BP3 VLCD 2VLCD/3 VLCD/3 VSS Sn VLCD 2VLCD/3 VLCD/3 VSS Sn+1 VLCD 2VLCD/3 VLCD/3 VSS Sn+2 VLCD 2VLCD/3 VLCD/3 VSS Sn+3 VLCD 2VLCD/3 VLCD/3 VSS state 1 VLCD 2VLCD/3 VLCD/3 0V -VLCD/3 -2VLCD/3 -VLCD state 2 VLCD 2VLCD/3 VLCD/3 0V -VLCD/3 -2VLCD/3 -VLCD LCD segments state 1 state 2 (a) Waveforms at driver. (b) Resultant waveforms at LCD segment. 013aaa211 Vstate1(t) = VSn(t) VBP0(t). Vstate2(t) = VSn(t) VBP1(t). Von(RMS)(t) = 0.577VLCD. Voff(RMS)(t) = 0.333VLCD. Fig 19. Waveforms for the 1:4 multiplex drive mode with 13 bias (line inversion mode) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 28 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.4.2.4 1:6 Multiplex drive mode When six backplanes are provided in the LCD, the 1:6 multiplex drive mode applies. The PCA9620 allows the use of 13 bias or 14 bias in this mode as shown in Figure 20 and Figure 21. Tfr BP0 VLCD 2VLCD / 3 VLCD / 3 VSS BP1 VLCD 2VLCD / 3 VLCD / 3 VSS BP2 VLCD 2VLCD / 3 VLCD / 3 VSS BP3 VLCD 2VLCD / 3 VLCD / 3 VSS BP4 VLCD 2VLCD / 3 VLCD / 3 VSS BP5 VLCD 2VLCD / 3 VLCD / 3 VSS Sn VLCD 2VLCD / 3 VLCD / 3 VSS Sn + 1 VLCD 2VLCD / 3 VLCD / 3 VSS LCD segments state 1 state 2 (a) Waveforms at driver VLCD 2VLCD / 3 state 1 VLCD / 3 VSS -VLCD / 3 -2VLCD / 3 -VLCD state 2 VLCD 2VLCD / 3 VLCD / 3 VSS -VLCD / 3 -2VLCD / 3 -VLCD (b) Resultant waveforms at LCD segment 001aal399 Vstate1(t) = VSn(t) VBP0(t). Vstate2(t) = VSn + 1(t) VBP0(t). Von(RMS)(t) = 0.509VLCD. Voff(RMS)(t) = 0.333VLCD. Fig 20. Waveforms for 1:6 multiplex drive mode with 13 bias (line inversion mode) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 29 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Tfr LCD segments VLCD 3VLCD / 4 state 1 state 2 BP0 VLCD / 4 VSS VLCD 3VLCD / 4 BP1 VLCD / 4 VSS VLCD 3VLCD / 4 BP2 VLCD / 4 VSS VLCD 3VLCD / 4 BP3 VLCD / 4 VSS VLCD 3VLCD / 4 BP4 VLCD / 4 VSS VLCD 3VLCD / 4 BP5 VLCD / 4 VSS VLCD Sn VLCD / 2 VSS VLCD Sn + 1 VLCD / 2 VSS (a) Waveforms at driver VLCD 3VLCD / 4 state 1 VLCD / 4 VSS -VLCD / 4 -3VLCD / 4 -VLCD VLCD 3VLCD / 4 VLCD / 2 VLCD / 4 VSS state 2 -VLCD / 4 -VLCD / 2 -3VLCD / 4 -VLCD (b) Resultant waveforms at LCD segment 001aal400 Vstate1(t) = VSn(t) VBP0(t). Vstate2(t) = VSn + 1(t) VBP0(t). Von(RMS)(t) = 0.467VLCD. Voff(RMS)(t) = 0.306VLCD. Fig 21. Waveforms for 1:6 multiplex drive mode with 14 bias (line inversion mode) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 30 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.4.2.5 VLCD 3VLCD / 4 1:8 Multiplex drive mode Tfr LCD segments state 1 state 2 BP0 VLCD / 4 VSS VLCD 3VLCD / 4 BP1 VLCD / 4 VSS VLCD 3VLCD / 4 BP2 VLCD / 4 VSS VLCD 3VLCD / 4 BP3 VLCD / 4 VSS VLCD 3VLCD / 4 BP4 3LCD / 4 VSS VLCD 3VLCD / 4 BP5 VLCD / 4 VSS VLCD 3VLCD / 4 BP6 VLCD / 4 VSS VLCD 3VLCD / 4 BP7 VLCD / 4 VSS VLCD Sn VLCD / 2 VSS VLCD Sn + 1 VLCD / 2 VSS (a) Waveforms at driver VLCD 3VLCD / 4 state 1 VLCD / 4 VSS -VLCD / 4 -3VLCD / 4 -VLCD state 2 VLCD 3VLCD / 4 VLCD / 2 VLCD / 4 VSS -VLCD / 4 -VLCD / 2 -3VLCD / 4 -VLCD (b) Resultant waveforms at LCD segment 001aal398 Vstate1(t) = VSn(t) VBP0(t). Vstate2(t) = VSn + 1(t) VBP0(t). Von(RMS)(t) = 0.424VLCD. Voff(RMS)(t) = 0.293VLCD. Fig 22. Waveforms for 1:8 multiplex drive mode with 14 bias (line inversion mode) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 31 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial VLCD 3/4 VLCD Tfr frame n Tfr frame n+1 LCD segments state 1 BP0 state 2 1/4 VLCD VSS VLCD 3/4 VLCD BP1 1/4 VLCD VSS VLCD 3/4 VLCD BP2 1/4 VLCD VSS VLCD 3/4 VLCD BP3 1/4 VLCD VSS VLCD 3/4 VLCD BP4 1/4 VLCD VSS VLCD 3/4 VLCD BP5 1/4 VLCD VSS VLCD 3/4 VLCD BP6 1/4 VLCD VSS VLCD 3/4 VLCD BP7 1/4 VLCD VSS VLCD Sn 1/2 VLCD VSS VLCD Sn + 1 1/2 VLCD VSS (a) Waveforms at driver state 1 VLCD 3/4 VLCD 1/2 VLCD 1/4 VLCD VSS 1/4 VLCD 1/2 VLCD 3/4 VLCD VLCD state 2 VLCD 3/4 VLCD 1/2 VLCD 1/4 VLCD VSS 1/4 VLCD 1/2 VLCD 3/4 VLCD VLCD (b) Resultant waveforms at LCD segment 001aam359 Vstate1(t) = VSn(t) VBP0(t). Vstate2(t) = VSn + 1(t) VBP0(t). Von(RMS)(t) = 0.424VLCD. Voff(RMS)(t) = 0.293VLCD. Fig 23. Waveforms for 1:8 multiplex drive mode with 14 bias (frame inversion mode) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 32 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial When eight backplanes are provided in the LCD, the 1:8 multiplex drive mode applies, as shown in Figure 22 and Figure 23. 8.4.3 VLCD generation VLCD can be generated and controlled on the chip by using software commands. When the internal charge pump is used, the programmed VLCD is available on pin VLCD. The charge pump generates a VLCD of up to 3 VDD2. The charge pump can be enabled or disabled with the CPE bit (see Table 9 on page 9). With bit CPC, the charge pump multiplier setting can be configured. The final value of VLCD is a combination of the programmed VPR[7:0] value and the output of the temperature compensation block, VT[7:0]. The system is shown in Figure 24. SLA SLB SLC SLD 0 OFFSET TEMPERATURE READOUT 8 8 TD -40 0 +20 +50 +80 TEMPERATURE n VPR[7:0] m 8 VLCD 013aaa257 Fig 24. VLCD generation including temperature compensation In Equation 6 the main parameters are the programmed digital value term and the compensated temperature term. V LCD = VPR 7:0 + VT 7:0 n + m (6) 1. VPR[7:0] is the binary value of the programmed voltage. 2. VT[7:0] is the binary value of the temperature compensated voltage. Its value comes from the temperature compensation block and is a two's complement which has the value 0h at 20 C. 3. m and n are fixed values (see Table 28). Table 28. Symbol Parameters of VLCD generation Value Unit m 3 V n 0.03 V Figure 25 shows how VLCD changes with the programmed value of VPR[7:0]. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 33 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial It has to be taken into account that the charge pump has to be configured (via bit CPC) properly to obtain the desired voltage range. For example, if VDD2 = 3.0 V and CPC is set to 2 VDD2 (logic 0) then the maximum theoretical value that the charge pump can reach is VLCD = 6.0 V. But in reality, lower values will be reached due to internal resistances, see Section 8.4.5. So, if the requested value for VLCD = 7.0 V then the charge pump has to be configured with CPC set to 3 VDD2 (logic 1). V LCD (2) 9V n (1) VDD2 m 00 01 02 03 04 05 06 ........................ C7 C8 C9 CA ... FC FD FE FF VPR[7:0] 013aaa258 (1) If VDD2 > 3.0 V then VPR[7:0] must be set so that VLCD > VDD2. (2) Automatic limitation for VLCD > 9.0 V. Fig 25. VLCD programming of PCA9620 (assuming VT[7:0] = 0h) Programmable range of VPR[7:0] is from 0h to FFh. This would allow achieving VLCD > 9.0 V, but the PCA9620 has a built-in automatic limitation of VLCD at 9.0 V. If VDD2 is higher than 3.0 V, then it is important that VPR[7:0] is set to a value such that the resultant VLCD (including the temperature correction of VT[7:0]) is higher than VDD2. 8.4.4 External VLCD supply VLCD can be directly supplied to the VLCD pin. In this case, the internal charge pump must not be enabled otherwise a high current may occur on pin VDD2 and pin VLCD. When VLCD is supplied externally, no internal temperature compensation occurs on this voltage even if bit TCE is set logic 1 (see Section 8.4.8 on page 38). The VLCD voltage which is supplied externally will be available at the segments and backplanes of the device through the chosen bias system. Also programming the VPR[7:0] bit field has no effect on the VLCD which is externally supplied. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 34 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.4.5 Charge pump driving capability Figure 26 illustrates the main factor determining how much current the charge pump can deliver. Regulated desired VLCD This supplies the segments and backplanes Theoretical VLCD value VLCD = 2 x VDD2 or VLCD = 3 x VDD2 Output Resistance Ro(cp) 013aaa259 Fig 26. Charge pump model (used to characterize the driving strength) The output resistance of the charge pump is specified in Table 36 on page 57. With these values, it can be calculated how much current the charge pump can drive under certain conditions. Example: Assuming that the normal operation point is at 25 C with VLCD = 7.0 V and VDD2 = 5.0 V and the charge pump is set to 2 VDD2. Then the theoretical value of VLCD is 10.0 V and the desired one is 7.0 V. The difference between the theoretical maximum value and desired one is 3.0 V. The charge pump resistance is nominally 0.85 k. Equation 7 shows the possible current that the charge pump could deliver: I load = V LCD R o cp (7) The result of this example is: I load = 3.0 V 0.85 k = 3.5 mA In cases where no extreme driving capability is needed, a command is available for decreasing the charge pump frequency (see Table 23 on page 13) and thus reducing the total current consumption. If the charge pump frequency is halved, then the driving capability is halved as well, whereas the output resistance doubles. 8.4.6 Charge pump frequency settings and power efficiency The PCA9620 offers the possibility to use different frequency settings for the charge pump. Bit CPF controls the frequency at which the charge pump is running (see Table 23 on page 13). This frequency has a direct influence on the current consumption of the IC but also on the charge pump driving capability. Using a lower charge pump frequency decreases the current consumption and the driving capability. The power efficiency of the charge pump determines in certain applications which frequency settings to choose for the CPF bit. Concerning the example shown in Figure 27: The current consumption was measured with * charge pump set to 2 VDD2 * VDD2 = 3.0 V * VPR[7:0] set to maximum to obtain the highest possible VLCD with this setup, which is close to 6.0 V The current load on pin VLCD determines the output power delivered by the IC: PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 35 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial P o = I load V LCD (8) The current consumption on pin VDD2 determines the input power taken by the IC: P i = I DD2 V DD2 (9) The ratio between these two numbers determines the charge pump power efficiency: p = Po Pi (10) 001aan027 90 p (%) 7 VLCD (V) 70 5 (3) (4) (1) (2) 50 3 30 0 200 400 600 1 1000 800 Iload (A) Charge pump set to 2 VDD2; VDD2 = 3 V. (1) p, full charge pump frequency. (2) p, half charge pump frequency. (3) VLCD, full frequency. (4) VLCD, half frequency. Fig 27. Power efficiency of the charge pump Loading the charge pump with higher currents decreases the output voltage. This decrease is determined by the charge pump driving capability, respectively by the output resistance of the charge pump (see Table 36 on page 57). The power efficiency calculation is only valid when the charge pump is running at its maximum peak frequency and regulates the generated VLCD voltage with full speed. In this case, the ripple on the VLCD voltage equals the internal charge pump frequency. Approximately, this could also be calculated with the parameter of the output resistance of the charge pump (see Table 36 on page 57), the load current, and the voltage needed to be provided by using Equation 7 on page 35. This value of Iload is close to the value of the load current needed for the application. If the application runs with VDD2 = 3.0 V, the load currents are up to 400 A (DC measured), and the VLCD generated voltages are up to 5.0 V, then - concerning power efficiency - it would be the best to have a charge pump frequency set to half frequency. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 36 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial If it is desired to change the charge pump frequency, it is recommended to make a graph like Figure 27 and understand what the application requirements are. This would basically imply to find out what would be the maximum VLCD requirements and what would be the maximum load currents required. Then it can be decided which is the best setting of bit CPF. Tuning the charge pump frequency might be a difficult task to do. It requires good knowledge of the application in which the IC is being used; therefore, NXP is recommending to keep the CPF bit set logic 0 to have the maximum charge pump frequency, thus having the maximum driving strength. 8.4.7 Temperature readout The PCA9620 has a built-in temperature sensor which provides an 8 bit digital value, TD[7:0], of the ambient temperature. This value can be read through the I2C interface (see Figure 50 on page 54). The actual temperature is determined from TD[7:0] using Equation 11: T (C) = 0.9375 TD 7:0 - 40 (11) The measurement needs about 5 ms to complete. it is repeated periodically as soon as bit TME is set logic 1 (see Table 10 on page 9). The time between measurements is linked to the system clock and hence varies with changes in the chosen frame frequency, see Table 29. Table 29. Temperature measurement update rate Selected frame frequency Temperature measurement update rate 60 Hz 3.3 s 200 Hz 1s 300 Hz 0.67 s Due to the nature of a temperature sensor, oscillations on the VLCD may occur. To avoid it, a filter has been implemented in PCA9620. The system is shown in Figure 28. TEMPERATURE MEASUREMENT BLOCK TD[7:0] unfiltered DIGITAL TEMPERATURE FILTER TD[7:0] filtered To the readout register via I2C-bus and to the VLCD compensation block enabled or disabled by bit TFE 013aaa260 Fig 28. Temperature measurement block with digital temperature filter Like any other filtering, the digital temperature filter (see Figure 28) introduces a certain delay in the measurement of temperature. This behavior is illustrated in Figure 29. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 37 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 001aal393 50 16 T (C)(3) T (C) 40 12 30 8 (1) (2) 20 4 (3) 10 0 -4 160 0 0 40 80 120 t (s) (1) Environment temperature, T1 (C). (2) Measured temperature, T2 (C). (3) Temperature deviation, T = T2 T1. Fig 29. Temperature measurement delay This delay may cause undesired effects at start-up when the environment temperature may be different than the reset value of the PCA9620 which is 20 C. In this case, it takes up to 30 s until the correct measured temperature value will be available. A control bit, TFE, is implemented to enable or disable the digital temperature filter. This bit is set logic 0 by default which means that the filter is disabled and the unfiltered environment temperature value is available to calculate the desired VLCD. 8.4.8 Temperature compensation of VLCD Due to the temperature dependency of the liquid crystal viscosity, the LCD controlling voltage VLCD might have to be adjusted at different temperatures to maintain optimal contrast. The temperature behavior of the liquid comes from the LCD manufacturer. The slope has to be set to compensate for the liquid behavior. Internal temperature compensation may be enabled via bit TCE. The ambient temperature range is split up into four equally sized regions and a different temperature coefficient can be applied to each (see Figure 30). Each coefficient can be selected from a choice of eight different slopes. Each one of these coefficients (see Table 30) may be independently selected via the temp-comp-SLA to temp-comp-SLD commands (see Table 5 on page 7). PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 38 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 30. Temperature coefficients SLA[2:0] to SLD[2:0] value Corresponding slope factor (mV/C) Temperature coefficients MA, MB, MC, MD[1] 000[2] 0 0.00 001 4 0.125 010 8 0.25 011 16 0.5 100 40 1.25 101 +4 0.125 110 +8 0.25 111 +16 0.5 [1] The relationship between the temperature coefficients MA to MD and the slope factor is derived from the 0.9375 0.03 slope 1000 following equation: Mx = ---------------- -------------- . [2] Default value. The slope factors imply a linear correction, however the implementation is set in steps of 30 mV (parameter n in Table 28 on page 33). SLA SLB SLC SLD TD[7:0] 0h 40h 20h 7Fh 60h VLCD with temperature compensation (V) zero offset at 20 C MA -40 MB -10 MC 20 MD 50 79 Temperature (C) 013aaa261 Fig 30. Example of segmented temperature coefficients Remark: After reset, VLCD is fixed because the VPR[7:0] bit field is reset logic 0. The value of VT[7:0] is generated by the reset value of TD[7:0] (40h, representing 20 C). Temperature compensation is implemented by adding an offset VT[7:0] to the VPR[7:0] value. VT[7:0] is a two's complement number that equals 0h at 20 C. The final result for VLCD calculation is an 8-bit positive number (see Equation 6 on page 33). Remark: Care must be taken that the ranges of VPR[7:0] and VT[7:0] do not cause clipping and hence undesired results. The device will not permit overflow or underflow and will clamp results to either end of the range. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 39 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial The Voffset(LCD) value can be calculated with the equations given in Table 31: V offset LCD = m V T Table 31. (12) Calculation of the temperature compensated voltage VT Temperature range TD[7:0] Offset equation for VT T 40 C 0h V T = - 32 MA - 32 MB 40 C T 10 C 0h to 20h V T = TD 7:0 - 32 MA - 32 MB 10 C < T 20 C 21h to 40h V T = TD 7:0 - 64 MB 20 C < T 50 C 41h to 60h V T = TD 7:0 - 64 MC 50 C < T < 80 C 61h to 7Eh V T = TD 7:0 - 96 MD + 32 MC 80 C T 7Fh[1] V T = 31 MD + 32 MC [1] No temperature compensation is possible above 80 C. Above this value, the system maintains the compensation value from 80 C. Example: Assumed that Tamb = 8 C; TD[7:0] = 22h; MB = 0.5: V offset LCD = m V T = m TD[7:0] - 64 MB = 30mV 34 - 64 - 0.5 = 30mV - 30 - 0.5 = 450mV (13) The VT[7:0] term is calculated using the digital temperature value TD[7:0] which is provided by the temperature measurement block (Section 8.4.7). Therefore the accuracy of the temperature measurement block (Tacc, see Table 36 on page 57) will be directly translated to the LCD voltage deviation VLCD. Since VT[7:0] = f[T,slope] and Tacc = 6 C then V T = T acc slope , where slope has one of the possible values specified in Table 30. This term will be added to the total LCD voltage deviation Voffset(LCD)tot over the temperature range. So the total VLCD offset will be: V offset LCD tot = V LCD + V T . 8.5 Oscillator The internal logic and LCD drive signals of the PCA9620 are timed by a frequency fclk which either is the built-in oscillator frequency fosc or equals an external clock frequency. 8.5.1 Internal oscillator When the internal oscillator is used, it is possible to make the clock signal available on pin CLK by using the oscillator-ctrl command (see Table 8 on page 8). If this is not intended, pin CLK should be left open. At power-on the signal at pin CLK is disabled and pin CLK is in 3-state. The duty cycle of the output clock provided on the CLK pin is not always 50 : 50. Table 18 on page 11 shows the expected duty cycle for each of the chosen frame frequencies. 8.5.2 External clock In applications where an external clock needs to be applied to the PCA9620, bit OSC (see Table 8 on page 8) must be set logic 1. In this case pin CLK becomes an input. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 40 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial The CLK signal is a signal that is fed into the VDD1 domain so it must have an amplitude equal to the VDD1 voltage supplied to the chip and be referenced to VSS. The clock frequency (fclk) determines the LCD frame frequency ffr. Remark: If an external clock is used then this clock signal must always be supplied to the device; removing the clock may freeze the LCD in a DC state, which is not suitable for the liquid crystal. Removal of the clock is possible when following the correct procedures. See Figure 13 on page 21 and Figure 14 on page 22. 8.5.3 Timing and frame frequency The timing of the PCA9620 organizes the internal data flow of the device. It includes the transfer of display data from the display RAM to the display segment outputs. The timing also generates the LCD frame frequency which it derives as an integer division of the clock frequency. The frame frequency is a fixed division of the internal clock or of the frequency applied to pin CLK when an external clock is used: f clk f fr = ------48 (14) When the internal clock is used, the clock and frame frequency can be programmed by software such that the nominal frame frequency can be chosen in steps of 10 Hz in the range of 60 Hz to 300 Hz (see Table 18 on page 11). Furthermore the nominal frame frequency is factory-calibrated with an accuracy of 15 %. When the internal clock is enabled at pin CLK by using bit COE, the duty ratio of the clock may change when choosing different values for the frame frequency prescaler. Table 18 on page 11 shows the different output duty ratios for each frame frequency prescaler setting. 8.6 Backplane outputs The LCD drive section includes eight backplane outputs: BP0 to BP7. The backplane output signals are generated based on the selected LCD multiplex drive mode. Table 32 describes which outputs are active for each of the multiplex drive modes and what signal is generated. Table 32. Multiplex drive mode Output pin 1:8 1:6 Product data sheet BP0 BP1 BP2 BP3 BP4 BP5 BP6 BP7 BP0 BP1 BP2 BP3 BP4 BP5 BP6 BP7 BP0 BP1 BP2 BP3 BP4 BP5 BP0[1] BP1[1] BP1[1] BP2[1] BP3[1] Signal 1:4 BP0 BP1 BP2 BP3 BP0[1] 1:2 BP0 BP1 BP0[1] BP1[1] BP0[1] BP1[1] BP0[1] BP1[1] static BP0 BP0[1] BP0[1] BP0[1] BP0[1] BP0[1] BP0[1] BP0[1] [1] PCA9620 Mapping of output pins and corresponding output signals with respect to the multiplex driving mode These pins may optionally be connected to the display to improve drive strength. Connect only with the corresponding output pin carrying the same signal. If not required, they can be left open-circuit. All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 41 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.7 Segment outputs The LCD drive section includes 60 segment outputs (S0 to S59) which must be connected directly to the LCD. The segment output signals are generated based on the multiplexed backplane signals and with data resident in the display register. When less than 60 segment outputs are required, the unused segment outputs must be left open-circuit. 8.8 Display register The display register holds the display data while the corresponding multiplex signals are generated. 8.9 Display RAM The display RAM is a static 60 8-bit RAM which stores LCD data. Logic 1 in the RAM bit map indicates the on-state of the corresponding LCD element; similarly, logic 0 indicates the off-state. There is a one-to-one correspondence between * the bits in the RAM bitmap and the LCD elements * the RAM columns and the segment outputs * the RAM rows and the backplane outputs. The display RAM bit map, Figure 31, shows row 0 to row 7 which correspond with the backplane outputs BP0 to BP7, and column 0 to column 59 which correspond with the segment outputs S0 to S59. In multiplexed LCD applications, the data of each row of the display RAM is time-multiplexed with the corresponding backplane (row 0 with BP0, row 1 with BP1, and so on). When display data is transmitted to the PCA9620, the display bytes received are stored in the display RAM in accordance with the selected LCD multiplex drive mode. The data is stored as it arrives and does not wait for the acknowledge cycle as with the commands. Depending on the current multiplex drive mode, data is stored singularly, in pairs, quadruples, sextuples or bytes. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 42 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial columns display RAM columns/segment outputs (S) static drive mode 0 1 2 3 4 55 56 57 58 59 0 bank 0 1 bank 1 2 bank 2 3 bank 3 4 bank 4 5 bank 5 6 bank 6 7 bank 7 multiplex 1:2 drive mode 0 1 2 3 4 55 56 57 58 59 0 bank 0 1 rows display RAM rows/ backplane outputs (BP) 2 bank 2 3 4 bank 4 5 6 bank 6 7 0 multiplex 1:4 drive mode 1 2 3 4 55 56 57 58 59 0 1 bank 0 2 3 4 5 bank 4 6 7 013aaa262 The display RAM bitmap shows the direct relationship between the display RAM column and the segment outputs, between the bits in a RAM row and the backplane outputs, and between the RAM rows and banks. Fig 31. Display RAM bitmap 8.9.1 Data pointer The addressing mechanism for the display RAM is realized using the data pointer. It allows the loading of an individual display data byte, or a series of display data bytes into any location of the display RAM. The sequence commences with the initialization of the data pointer by the load-data-pointer command. Following this command, an arriving data byte is stored starting at the display RAM address indicated by the data pointer. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 43 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial The data pointer is automatically incremented in accordance with the chosen LCD multiplex drive mode configuration. That is, after each byte is stored, the contents of the data pointer are incremented * * * * * by eight (static drive mode) by four (1:2 multiplex drive mode) by two (1:4 multiplex drive mode) by one or two (1:6 multiplex drive mode), see Figure 38 on page 47 by one (1:8 multiplex drive mode) If the data pointer reaches the end of the RAM row, it is automatically wrapped around to address 0. This means that it can be continuously written to or read from the display RAM. The data pointer should always be set to an address where the remaining RAM is divisible by eight because odd bits will be discarded (see Figure 33). This behavior is only shown in static drive mode because the 60 RAM cells cannot be divided by eight without remainder. If an I2C-bus data access is terminated early, then the state of the data pointer is unknown. The data pointer must then be re-written before further RAM accesses. 8.9.1.1 RAM filling in static drive mode In the static drive mode the eight transmitted data bits are placed in eight successive display RAM columns in row 0 (see Figure 32). columns display RAM columns/segment outputs (S) rows 0 1 2 3 4 5 6 7 55 56 57 58 59 display RAM rows/ 0 b7 b6 b5 b4 b3 b2 b1 b0 backplane outputs (BP) b7 b6 b5 b4 b3 b2 b1 b0 MSB LSB transmitted data byte 013aaa263 Fig 32. Display RAM filling order in static drive mode In order to fill the whole RAM row, 8 bytes must be sent to the PCA9620, but the last 4 bits from the last byte are discarded, and the data pointer is wrapped around to column 0 to start a possible RAM content update (see Figure 33). PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 44 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial data pointer 0 1 2 3 4 5 6 48 49 50 51 52 53 54 55 56 57 58 59 7 0 a7 a6 a5 a4 a3 a2 a1 a0 f7 f6 f5 f4 f3 f2 f1 f0 g7 g6 g5 g4 g3 g2 g1 g0 discarded display RAM wrap around 013aaa287 Fig 33. Discarded bits and data pointer wrap around at the end of data transmission 8.9.1.2 RAM filling in 1:2 multiplex drive mode In the 1:2 multiplex drive mode the eight transmitted data bits are placed in four successive display RAM columns of two rows (see Figure 34). columns display RAM columns/segment outputs (S) rows 0 1 2 3 4 5 6 7 55 56 57 58 59 display RAM rows/ 0 b7 b5 b3 b1 backplane outputs 1 b6 b4 b2 b0 (BP) LSB b7 b6 b5 b4 b3 b2 b1 b0 MSB transmitted data byte 013aaa264 Fig 34. Display RAM filling order in 1:2 multiplex drive mode In order to fill the whole two RAM rows 15 bytes need to be sent to the PCA9620. After the last byte sent, the data pointer is wrapped around to column 0 to start a possible RAM content update (see Figure 35). Even if a data byte is transmitted during the wrapping of the data pointer, then all the bits in the byte will be written correctly. data pointer 0 1 2 3 4 5 6 7 55 56 57 58 59 0 b1 display RAM 1 b0 b7 b5 b3 b6 b4 b2 wrap around 013aaa288 Fig 35. Data pointer wrap around in 1:2 multiplex drive mode 8.9.1.3 RAM filling in 1:4 multiplex drive mode In the 1:4 multiplex drive mode the eight transmitted data bits are placed in two successive display RAM columns of four rows (see Figure 36). PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 45 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial columns display RAM columns/segment outputs (S) 0 1 2 0 b7 b3 1 b6 b2 rows 3 4 5 6 7 55 56 57 58 59 2 b5 b1 display RAM rows/ backplane outputs (BP) 3 b4 b0 b7 b6 b5 b4 b3 b2 b1 b0 MSB LSB transmitted data byte 013aaa265 Fig 36. Display RAM filling order in 1:4 multiplex drive mode In order to fill the whole four RAM rows 30 bytes need to be sent to the PCA9620. After the last byte sent, the data pointer is wrapped around to column 0 to start a possible RAM content update (see Figure 37). Even if a data byte is transmitted during the wrapping of the data pointer, all the bits in the byte will be written correctly. columns display RAM columns/segment outputs (S) data pointer display RAM 0 1 0 b3 1 b2 2 3 4 5 6 7 55 56 57 58 59 b7 b6 2 b1 b5 3 b0 b4 wrap around 013aaa289 Fig 37. Data pointer wrap around in 1:4 multiplex drive mode 8.9.1.4 RAM filling in 1:6 multiplex drive mode In the 1:6 multiplex drive mode the RAM is organized in six rows and 60 columns. The eight transmitted data bits are placed in such a way, that a column is filled up (see Figure 38). PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 46 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial columns display RAM columns/segment outputs (S) data pointer incrementation 0 1 2 3 4 5 6 7 55 56 57 58 59 0 a7 a1 b3 c5 rows 1 a6 a0 b2 c4 2 a5 b7 b1 c3 display RAM rows/ backplane outputs (BP) 3 a4 b6 b0 c2 4 a3 b5 c7 c1 5 a2 b4 c6 c0 MSB LSB a7 a6 a5 a4 a3 a2 a1 a0 b7 b6 b5 b4 b3 b2 b1 b0 c7 c6 c5 c4 c3 c2 c1 c0 transmitted data bytes 013aaa266 Fig 38. Display RAM filling order in 1:6 multiplex drive mode The remaining bits are wrapped up into the next column. In order to fill the whole RAM addresses 45 bytes need to be sent to the PCA9620. After the last byte sent, the data pointer is wrapped around to column 0 to start a possible RAM content update (see Figure 39). Even if a data byte is transmitted during the wrapping of the data pointer, all the bits in the byte will be written correctly. data pointer display RAM 0 1 2 3 4 5 6 7 55 56 57 58 59 0 b3 c5 a7 a1 1 b2 c4 a6 a0 2 b1 c3 a5 b7 3 b0 c2 a4 b6 4 c7 c1 a3 b5 5 c6 c0 a2 b4 wrap around 013aaa290 Fig 39. Data pointer wrap around in 1:6 multiplex drive mode 8.9.1.5 RAM filling in 1:8 multiplex drive mode In the 1:8 multiplex drive mode the eight transmitted data bits are placed into eight rows of one display RAM column (see Figure 40). PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 47 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial columns transmitted data byte display RAM columns/segment outputs (S) MSB LSB b7 b6 b5 b4 b3 b2 b1 b0 0 1 2 3 4 5 6 7 55 56 57 58 59 0 b7 1 b6 rows 2 b5 3 b4 display RAM rows/ backplane outputs (BP) 4 b3 5 b2 6 b1 7 b0 013aaa267 Fig 40. Display RAM filling order in 1:8 multiplex drive mode In order to fill the whole RAM addresses 60 bytes need to be sent to the PCA9620. After the last byte sent, the data pointer is wrapped around to column 0 to start a possible RAM content update (see Figure 41). In this case, there is no situation possible where a transmitted data byte can be written over the RAM boundary. data pointer display RAM 0 1 2 3 4 5 6 7 55 56 57 58 59 0 b7 a7 1 b6 a6 2 b5 a5 3 b4 a4 4 b3 a3 5 b2 a2 6 b1 a1 7 b0 a0 wrap around 013aaa291 Fig 41. Data pointer wrap around in 1:8 multiplex drive mode 8.9.2 Bank selection A RAM bank can be thought of as a collection of RAM rows. The PCA9620 includes a RAM bank switching feature in the static, 1:2, and 1:4 multiplex drive modes. The RAM bank switching gives the provision for preparing display information in an alternative bank and to be able to switch to it once it is complete. Input and output banks can be set independently from one another with the input-bank-select and the output-bank-select commands; Figure 42 shows the concept. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 48 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial INPUT-BANK-SELECT COMMAND CONTROLS THE INPUT DATA PATH OUTPUT-BANK-SELECT COMMAND CONTROLS THE OUTPUT DATA PATH BANK 0 MICROCONTROLLER RAM DISPLAY BANK 4 013aaa422 Fig 42. Example of bank selection in 1:4 multiplex mode In Figure 42 an example is shown for 1:4 multiplex drive mode. The displayed data is read from the first four rows of the memory (bank 0), while the transmitted data is stored in the second four rows of the memory (bank 4) which is currently not accessed for the reading. Therefore different content can be loaded into the first and second four RAM rows which will be immediately displayed on the LCD by switching it with the output-bank-select command (see Figure 43). columns display RAM columns/segment outputs (S) 0 1 2 3 4 5 6 7 55 56 57 58 59 0 1 rows to the LCD 2 display RAM rows/ backplane outputs (BP) output RAM bank 3 4 5 to the RAM 6 7 input RAM bank 013aaa424 Fig 43. Example of the input-bank-select and the output-bank-select command with multiplex drive mode 1:4 8.9.2.1 Input-bank-select The input-bank-select command (see Table 19 on page 12) loads display data into the display RAM in accordance with the selected LCD drive configuration. * In static drive mode, an individual content can be stored in each RAM bank (bank 0 to bank 7 which corresponds to row 0 to row 7). * In 1:2 multiplex drive mode, individual content for RAM bank 0 (row 0 and row 1), RAM bank 2 (row 2 and row 3), RAM bank 4 (row 4 and 5) and RAM bank 6 (row 6 and row 7) can be stored. * In 1:4 multiplex drive mode individual content can be stored in RAM bank 0 (row 0 to row 3) and RAM bank 4 (row 4 to row 7). The input-bank-select command works independently to the output-bank-select. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 49 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 8.9.2.2 Output-bank-select The output-bank-select command (see Table 20 on page 12) selects the display RAM transferring it to the display register in accordance with the selected LCD drive configuration. * In the static drive mode, it is possible to request the content of RAM bank 1 (row 1) to RAM bank 7 (row 7) for display instead of the default RAM bank 0 (row 0). * In 1:2 multiplex drive mode, the content of RAM bank 2 (row 2 and row 3) or of RAM bank 4 (row 4 and row 5) or of RAM bank 6 (row 6 and row 7) may be selected instead of the default RAM bank 0 (row 0 and row 1). * In 1:4 multiplex drive mode, the content of RAM bank 4 (row 4, 5, 6, and 7) may be selected instead of RAM bank 0 (row 0, 1, 2, and 3). The output-bank-select command works independently to the input-bank-select. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 50 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 9. I2C-bus interface characteristics The I2C-bus is for bidirectional, two-line communication between different ICs or modules. The two lines are a Serial DAta line (SDA) and a Serial CLock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus is not busy. 9.1 Bit transfer One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse as changes in the data line at this time will be interpreted as a control signal (see Figure 44). SDA SCL data line stable; data valid change of data allowed mba607 Fig 44. Bit transfer 9.2 START and STOP conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW change of the data line, while the clock is HIGH is defined as the START condition (S). A LOW-to-HIGH change of the data line while the clock is HIGH is defined as the STOP condition (P). The START and STOP conditions are shown in Figure 45. SDA SDA SCL SCL S P START condition STOP condition mbc622 Fig 45. Definition of START and STOP conditions 9.3 System configuration A device generating a message is a transmitter; a device receiving a message is the receiver. The device that controls the message is the master; and the devices which are controlled by the master are the slaves. The system configuration is shown in Figure 46. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 51 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial MASTER TRANSMITTER/ RECEIVER SLAVE TRANSMITTER/ RECEIVER SLAVE RECEIVER MASTER TRANSMITTER MASTER TRANSMITTER/ RECEIVER SDA SCL mga807 Fig 46. System configuration 9.4 Acknowledge The number of data bytes transferred between the START and STOP conditions from transmitter to receiver is unlimited. Each byte of eight bits is followed by an acknowledge cycle. * A slave receiver which is addressed must generate an acknowledge after the reception of each byte. * Also a master receiver must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. * The device that acknowledges must pull-down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse (set-up and hold times must be taken into consideration). * A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition. Acknowledgement on the I2C-bus is shown in Figure 47. data output by transmitter not acknowledge data output by receiver acknowledge SCL from master 1 2 8 9 S START condition clock pulse for acknowledgement mbc602 Fig 47. Acknowledgement on the I2C-bus PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 52 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 9.5 I2C-bus controller The PCA9620 acts as an I2C-bus slave receiver. It does not initiate I2C-bus transfers or transmit data to an I2C-bus master receiver. The only data output from PCA9620 are the acknowledge signals and the temperature readout byte of the selected device. 9.6 Input filters To enhance noise immunity in electrically adverse environments, RC low-pass filters are provided on the SDA and SCL lines. 9.7 I2C-bus slave address Device selection depends on the I2C-bus slave address. Four different I2C-bus slave addresses can be used to address the PCA9620 (see Table 33). Table 33. I2C slave address Slave address Bit 7 6 5 4 3 2 1 MSB slave address 0 0 LSB 1 1 1 0 A1 A0 R/W The least significant bit of the slave address byte is bit R/W. Bit 1 and bit 2 of the slave address are defined by connecting the inputs A0 and A1 to either VSS (logic 0) or VDD (logic 1). Therefore, four instances of PCA9620 can be distinguished on the same I2C-bus. 9.8 I2C-bus protocol R/W = 0 slave address control byte A A C R S 0 1 1 1 0 0 A 1 0 O S RAM/command byte M A S B L S P B EXAMPLES a) transmit two bytes of RAM data S 0 1 1 1 0 A A 0 A 0 1 1 0 RAM DATA A RAM DATA A A COMMAND A 0 0 A COMMAND A P A COMMAND A 0 1 A RAM DATA A A P b) transmit two command bytes S 0 1 1 1 0 A A 0 A 1 0 1 0 c) transmit one command byte and two RAM date bytes S 0 1 1 1 0 A A 0 A 1 0 1 0 RAM DATA A P 013aaa293 Fig 48. I2C-bus protocol write mode PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 53 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial The I2C-bus protocol is shown in Figure 48. The sequence is initiated with a START condition (S) from the I2C-bus master which is followed by one of the four PCA9620 slave addresses available. All PCA9620's with the corresponding A1 and A0 level acknowledge in parallel to the slave address, but all PCA9620 with the alternative A1 and A0 levels ignore the whole I2C-bus transfer. After acknowledgement, a control byte follows which defines if the next byte is RAM or command information. The control byte also defines if the next byte is a control byte or further RAM or command data. Table 34. Control byte description Bit Symbol 7 CO 6 Value Description continue bit 0 last control byte 1 control bytes continue RS register selection 0 command register 1 5 to 0 - data register - not relevant MSB 7 6 5 4 CO RS 3 2 1 LSB 0 not relevant mgl753 Fig 49. Control byte format In this way it is possible to configure the device and then fill the display RAM with little overhead. The display bytes are stored in the display RAM at the address specified by the data pointer. The acknowledgement after each byte is made only by the (A0 and A1) addressed PCA9620. After the last display byte, the I2C-bus master issues a STOP condition (P). Alternatively a START may be issued to RESTART an I2C-bus access. If a temperature readout (byte TD[7:0]) is made the R/W bit must be logic 1 and then the next data byte following is provided by the PCA9620 as shown in Figure 50. R/W = 1 slave address S 0 1 1 1 0 temperature readout byte M A A 1 A S 1 0 B acknowledge from PCA9620 L S A P B acknowledge from master 013aaa294 Fig 50. I2C-bus protocol read mode PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 54 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 10. Internal circuitry VDD1 A0, A1, T1, T2, CLK T3, VLCD, SDA, SCL, VDD1, VDD2 VSS VLCD VSS BP0 to BP7, S0 to S59 VSS 013aaa295 Fig 51. Device protection diagram 11. Safety notes CAUTION This device is sensitive to ElectroStatic Discharge (ESD). Observe precautions for handling electrostatic sensitive devices. Such precautions are described in the ANSI/ESD S20.20, IEC/ST 61340-5, JESD625-A or equivalent standards. CAUTION Static voltages across the liquid crystal display can build up when the LCD supply voltage (VLCD) is on while the IC supply voltage (VDD) is off, or vice versa. This may cause unwanted display artifacts. To avoid such artifacts, VLCD and VDD must be applied or removed together. CAUTION Semiconductors are light sensitive. Exposure to light sources can cause the IC to malfunction. The IC must be protected against light. The protection must be applied to all sides of the IC. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 55 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 12. Limiting values Table 35. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VDD1 supply voltage 1 analog and digital 0.5 +6.5 V VDD2 supply voltage 2 charge pump 0.5 +6.5 V IDD1 supply current 1 analog and digital 50 +50 mA IDD2 supply current 2 charge pump 50 +50 mA VLCD LCD supply voltage 0.5 +10 V IDD(LCD) LCD supply current 50 +50 mA Vi input voltage 0.5 +6.5 V II input current 10 +10 mA VO output voltage 0.5 +10 V 0.5 +6.5 V IO output current 10 +10 mA ISS ground supply current 50 +50 mA Ptot total power dissipation - 400 mW P/out power dissipation per output - 100 mW VESD electrostatic discharge voltage on pins CLK, SDA, SCL, A0, A1, T1, T2, T3 on pins S0 to S59, BP0 to BP7 on pins SDA, CLK PCA9620 Product data sheet HBM [1] - 4000 V CDM [2] - 1500 V - 100 mA 65 +150 C 40 +105 C Ilu latch-up current [3] Tstg storage temperature [4] Tamb ambient temperature operating device [1] Pass level; Human Body Model (HBM), according to Ref. 8 "JESD22-A114". [2] Pass level; Charged-Device Model (CDM), according to Ref. 9 "JESD22-C101". [3] Pass level; latch-up testing according to Ref. 10 "JESD78" at maximum ambient temperature (Tamb(max)). [4] According to the store and transport requirements (see Ref. 14 "UM10569") the devices have to be stored at a temperature of +8 C to +45 C and a humidity of 25 % to 75 %. All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 56 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 13. Static characteristics Table 36. Static characteristics VDD1 = 2.5 V to 5.5 V; VDD2 = 2.5 V to 5.5 V; VSS = 0 V; VLCD = 2.5 V to 9.0 V; Tamb = 40 C to +105 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 2.5 - 5.5 V 2.5 - 5.5 V Supplies VDD1 supply voltage 1 VDD2 supply voltage 2 VDD2 VDD1 LCD supply voltage VLCD VDD2 VLCD [1] 2.5 - 9.0 V [2][3] 0.10 - +0.10 V VLCD LCD voltage variation IDD(pd) power-down mode supply on pin VDD1 current [4][5] - 1.0 3.0 A IDD1 supply current 1 [5][6] - 100 200 A IDD2 supply current 2 charge pump off; external VLCD [5][6] - 0.5 3.0 A charge pump on; internal VLCD [5][7] - 250 550 A - 125 250 A - 12 35 A VDD1 = VDD2 = 5.0 V; VLCD = 6.99 V fosc = 9.6 kHz IDD(LCD) LCD supply current external VLCD [5][8] ILCD(pd) power-down LCD current external VLCD [4][5] RO output resistance of charge pump (driving capabilities) Tacc temperature accuracy charge pump set to 2 VDD2; Iload = 3 mA (on pin VLCD) [9] 0.2 0.85 1.6 k charge pump set to 3 VDD2; Iload = 2 mA (on pin VLCD) [10] 2.0 3.2 4.5 k Tamb = 40 C to +105 C 6 - +6 C Tamb = 27 C 4 - +4 C readout temperature error; VDD1 = 5.0 V Logic VI input voltage VSS 0.5 - VDD + 0.5 V VIL LOW-level input voltage on pins CLK, A1, A0 - - 0.3VDD V VIH HIGH-level input voltage on pins CLK, A1, A0 0.7VDD - - V VO output voltage 0.5 - VDD + 0.5 V VOH HIGH-level output voltage on pin CLK 0.8VDD - - V VOL LOW-level output voltage - - 0.2VDD V IOH HIGH-level output current output source current; VOH = 4.6 V; VDD = 5 V; on pin CLK 1 - - mA IOL LOW-level output current 1 - - mA VPOR power-on reset voltage [11] - - 1.6 V leakage current [12] - 0 - A IL PCA9620 Product data sheet on pin CLK output sink current; VOL = 0.4 V; VDD = 5 V; on pin CLK Vi = VDD or VSS; on pins CLK, A1, A0, T1, T2, T3 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 57 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 36. Static characteristics ...continued VDD1 = 2.5 V to 5.5 V; VDD2 = 2.5 V to 5.5 V; VSS = 0 V; VLCD = 2.5 V to 9.0 V; Tamb = 40 C to +105 C; unless otherwise specified. Symbol I2C-bus; Parameter Conditions Min Typ Max Unit pins SDA and SCL VI input voltage VSS 0.5 - 5.5 V VIL LOW-level input voltage pins SCL, SDA - - 0.3VDD V VIH HIGH-level input voltage pins SCL, SDA 0.7VDD - - V VO output voltage pins SCL, SDA 0.5 - 5.5 V IOL LOW-level output current VOL = 0.4 V; VDD = 5 V; on pin SDA 3 - - mA IL leakage current VI = VDD or VSS [12] - 0 - A output voltage variation on pins BP0 to BP7 [13] 15 - +15 mV on pins S0 to S59 [14] 15 - +15 mV VLCD = 7 V; on pins BP0 to BP7 [15] 0.3 0.8 1.5 k VLCD = 7 V; on pins S0 to S59 [15] 0.6 1.5 3 k LCD outputs VO output resistance RO [1] When supplying external VLCD it must be VLCD VDD2. Also when using the internal charge pump to generate a certain VLCD, VPR[7:0] must be set to a value that the voltage is higher than VDD2 (see Section 8.4.3 on page 33). [2] Calibrated at testing stage. VLCD temperature compensation is disabled. [3] According to Equation 6 on page 33: VLCD = 133 0.03 + 3 = 6.99 V. [4] Display is disabled; I2C-bus inactive; temperature measurement disabled. [5] The typical value is defined at VDD1 = VDD2 = 5.0 V, VLCD = 7.0 V and 30 C. [6] Temperature measurement enabled; 1:8 multiplex drive mode; 14 bias; display enabled; LCD outputs are open circuit; RAM is all written with logic 1; inputs at VSS or VDD; internal clock with the default prescale factor; I2C-bus inactive. [7] VDD2 = 5.0 V; charge pump set to 2 VDD2; VPR[7:0] set for VLCD = 7.0 V; 1:8 multiplex drive mode; 14 bias; temperature measurement enabled; display enabled; LCD outputs are open circuit; RAM is all written with logic 1; inputs at VSS or VDD; external clock with 50 % duty factor; I2C-bus inactive. [8] External supplied VLCD = 7.0 V; 1:8 multiplex drive mode; 14 bias; temperature measurement enabled; display enabled; LCD outputs are open circuit; RAM is all written with logic 1; inputs at VSS or VDD; external clock with 50 % duty factor; I2C-bus inactive. [9] VDD2 = 5.0 V; charge pump set to 2 VDD2; VPR[7:0] set for VLCD = 9.0 V; display disabled; CPF (see Table 23 on page 13) set logic 0. [10] VDD2 = 4.0 V; charge pump set to 3 VDD2; VPR[7:0] set for VLCD = 9.0 V; display disabled; CPF (see Table 23 on page 13) set logic 0. [11] If VDD1 > VPOR then no reset occurs. [12] In case of an ESD event, the value may increase slightly. [13] Variation between any 2 backplanes on a given voltage level; static measured. [14] Variation between any 2 segments on a given voltage level; static measured. [15] Outputs measured one at a time. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 58 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 001aan026 8.3 VLCD (V) (3) 7.8 7.3 (1) 6.8 6.3 (2) 5.8 -50 0 50 100 150 temperature (C) (1) VPR[7:0] = 85h. (2) VPR[7:0] = 64h. (3) VPR[7:0] = A4h. Temperature compensation disabled. Fig 52. Typical VLCD with respect to temperature 001aan023 120 IDD1 (A) 100 80 60 -40 0 40 80 120 temperature (C) VDD1 = 5.0 V. Fig 53. Typical IDD1 with respect to temperature PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 59 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 001aan024 300 IDD2 (A) 260 220 180 140 100 -40 0 40 80 120 temperature (C) Charge pump set to 2 VDD2; VLCD = 7.0 V; VDD1 = VDD2 = 5.0 V. Fig 54. Typical IDD2 with respect to temperature 001aan025 140 ILCD (A) 120 100 80 -40 0 40 80 120 temperature (C) VLCD = 7.0 V, external supplied; VDD1 = VDD2 = 5.0 V; display enabled, but no display attached. Fig 55. Typical ILCD with respect to temperature PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 60 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 14. Dynamic characteristics Table 37. Dynamic characteristics VDD1 = 2.5 V to 5.5 V; VDD2 = 2.5 V to 5.5 V; VSS = 0 V; VLCD = 2.5 V to 9.0 V; Tamb = 40 C to +105 C; unless otherwise specified. Symbol Parameter fosc oscillator frequency fclk(ext) external clock frequency tclk(H) HIGH-level clock time tclk(L) LOW-level clock time Conditions on pin CLK; see Table 18 on page 11 [1][2] external clock source used Min Typ Max Unit 8160 9600 11040 Hz 450 - 14500 Hz 33 - - s 33 - - s Timing characteristics: I2C-bus[3] fSCL SCL frequency - - 400 kHz tBUF bus free time between a STOP and START condition 1.3 - - s tHD;STA hold time (repeated) START condition 0.6 - - s tSU;STA set-up time for a repeated START condition 0.6 - - s tVD;DAT data valid time [4] - - 0.9 s tVD;ACK data valid acknowledge time [5] - - 0.9 s tLOW LOW period of the SCL clock 1.3 - - s tHIGH HIGH period of the SCL clock 0.6 - - s tf fall time of both SDA and SCL signals - - 0.3 s tr rise time of both SDA and SCL signals - - 0.3 s Cb capacitive load for each bus line - - 400 pF tSU;DAT data set-up time 100 - - ns tHD;DAT data hold time 0 - - ns tSU;STO set-up time for STOP condition 0.6 - - s tw(spike) spike pulse width - - 50 ns [1] Internal calibration made with OTP so that the maximum variation is 15 % over whole temperature and voltage range. The typical fosc generates a typical frame frequency of 200 Hz when the default frequency division factor is used (see Section 8.5.3 on page 41). [2] The typical value is defined at VDD1 = VDD2 = 5.0 V and 30 C. [3] All timing values are valid within the operating supply voltage and ambient temperature range and are referenced to VIL and VIH with an input voltage swing of VSS to VDD. [4] tVD;DAT = minimum time for valid SDA output following SCL LOW. [5] tVD;ACK = time for acknowledgement signal from SCL LOW to SDA output LOW. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 61 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 1/fclk tclk(H) tclk(L) 0.7 VDD CLK 0.3 VDD 013aaa296 Fig 56. Driver timing waveforms protocol bit 7 MSB (A7) START condition (S) tSU;STA tLOW bit 6 (A6) tHIGH 1/f bit 0 (R/W) acknowledge (A) STOP condition (P) SCL SCL tBUF tr tf SDA tSU;DAT tHD;STA tHD;DAT tVD;DAT tVD;ACK tSU;STO 013aaa417 Fig 57. I2C-bus timing waveforms 15. Test information 15.1 Quality information This product has been qualified in accordance with the Automotive Electronics Council (AEC) standard Q100 - Failure mechanism based stress test qualification for integrated circuits, and is suitable for use in automotive applications. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 62 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 16. Package outline LQFP80: plastic low profile quad flat package; 80 leads; body 12 x 12 x 1.4 mm SOT315-1 c y X A 60 41 40 Z E 61 e E HE A A2 (A 3) A1 w M bp Lp L pin 1 index 80 21 detail X 20 1 ZD e v M A w M bp D B HD v M B 0 5 10 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e mm 1.6 0.16 0.04 1.5 1.3 0.25 0.27 0.13 0.18 0.12 12.1 11.9 12.1 11.9 0.5 HD HE 14.15 14.15 13.85 13.85 L Lp v w y 1 0.75 0.30 0.2 0.15 0.1 Z D (1) Z E (1) 1.45 1.05 7o o 0 1.45 1.05 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT315-1 136E15 MS-026 JEITA EUROPEAN PROJECTION ISSUE DATE 00-01-19 03-02-25 Fig 58. Package outline SOT315-1 (LQFP80) PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 63 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 17. Bare die outline Bare die; 80 bonding pads PCA9620U D pin 1 index 80 61 1 60 e x 0 X 0 y E (1) 41 20 21 40 A P4 P3 P2 P1 detail X Notes 1. Marking code: PC9620-1 Outline version pca9620u_do References IEC JEDEC JEITA European projection Issue date 11-09-15 11-09-26 PCA9620U Fig 59. Bare die outline of PCA9620 PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 64 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 38. Dimensions of PCA9620 Original dimensions are in mm. Unit (mm) A D[1] E[1] e[2] P1[3] P2[4] P3[3] P4[4] max - - - 0.203 - - - - nom 0.38 3.166 3.166 - 0.065 0.056 0.065 0.056 min - - - 0.075 - - - - [1] Dimension includes saw lane (70 m). [2] See Table 39. [3] P1 and P3: pad size. [4] P2 and P4: passivation opening. Table 39. Bonding pad description of PCA9620 All x/y coordinates represent the position of the center of each pad with respect to the center (x/y = 0) of the chip; see Figure 59. Symbol S20 Pad 1 Location Pitch Description X(m) Y(m) X(m) Y(m) 1497.3 1208.7 - - S21 2 1497.3 1086.3 0 122.4 S22 3 1497.3 963.9 0 122.4 S23 4 1497.3 841.5 0 122.4 S24 5 1497.3 719.1 0 122.4 S25 6 1497.3 568.8 0 150.3 S26 7 1497.3 446.4 0 122.4 S27 8 1497.3 324.0 0 122.4 S28 9 1497.3 201.6 0 122.4 S29 10 1497.3 79.2 0 150.3 S30 11 1497.3 71.1 0 122.4 S31 12 1497.3 193.5 0 122.4 S32 13 1497.3 315.9 0 122.4 S33 14 1497.3 438.3 0 122.4 S34 15 1497.3 560.7 0 122.4 S35 16 1497.3 711.0 0 122.4 S36 17 1497.3 833.4 0 122.4 S37 18 1497.3 955.8 0 122.4 S38 19 1497.3 1078.2 0 122.4 S39 20 1497.3 1200.6 0 122.4 S40 21 1204.2 1497.3 - - S41 22 1081.8 1497.3 122.4 0 S42 23 959.4 1497.3 122.4 0 S43 24 837.0 1 497.3 122.4 0 S44 25 714.6 1497.3 122.4 0 S45 26 564.3 1497.3 150.3 0 S46 27 441.9 1497.3 122.4 0 PCA9620 Product data sheet LCD segment output All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 65 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 39. Bonding pad description of PCA9620 ...continued All x/y coordinates represent the position of the center of each pad with respect to the center (x/y = 0) of the chip; see Figure 59. Symbol Pad Location X(m) Pitch Y(m) Description X(m) Y(m) S47 28 319.5 1497.3 122.4 0 S48 29 197.1 1497.3 122.4 0 S49 30 74.7 1497.3 122.4 0 S50 31 75.6 1497.3 150.3 0 S51 32 198.0 1497.3 122.4 0 S52 33 320.4 1497.3 122.4 0 S53 34 442.8 1497.3 122.4 0 S54 35 565.2 1497.3 122.4 0 S55 36 715.5 1497.3 150.3 0 S56 37 837.9 1497.3 122.4 0 S57 38 960.3 1497.3 122.4 0 S58 39 1082.7 1497.3 122.4 0 LCD segment output S59 40 1205.1 1497.3 122.4 0 BP0 41 1497.3 1201.5 - - BP1 42 1497.3 1077.3 0 124.2 BP2 43 1497.3 953.1 0 124.2 BP3 44 1497.3 828.9 0 124.2 BP4 45 1497.3 676.8 0 152.1 BP5 46 1497.3 552.6 0 124.2 BP6 47 1497.3 428.4 0 124.2 BP7 48 1497.3 304.2 0 124.2 VLCD 49 1497.3 171.9 0 132.3 LCD supply voltage VDD2 50 1497.3 47.7 0 124.2 supply voltage 2 (charge pump) VDD1 51 1497.3 76.5 0 124.2 supply voltage 1 (analog and digital) VSS 52 1497.3 166.5 0 90 ground supply voltage T1 53 1497.3 241.2 0 74.7 test pin T2 54 1497.3 315.9 0 74.7 T3 55 1497.3 430.2 0 114.3 CLK 56 1497.3 620.1 0 189.9 internal oscillator output, external oscillator input A0 57 1497.3 729.9 0 109.8 I2C-bus slave address selection bit A1 58 1497.3 806.4 0 76.5 SCL 59 1497.3 913.5 0 107.1 I2C-bus serial clock SDA 60 1497.3 1116.9 0 203.4 I2C-bus serial data S0 61 1205.1 1497.3 - - LCD segment output S1 62 1082.7 1497.3 122.4 0 S2 63 960.3 1497.3 122.4 0 S3 64 837.9 1497.3 122.4 0 S4 65 715.5 1497.3 122.4 0 PCA9620 Product data sheet LCD backplane output All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 66 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 39. Bonding pad description of PCA9620 ...continued All x/y coordinates represent the position of the center of each pad with respect to the center (x/y = 0) of the chip; see Figure 59. Symbol Pad Location X(m) Pitch Y(m) X(m) Description Y(m) S5 66 565.2 1497.3 150.3 0 S6 67 442.8 1497.3 122.4 0 S7 68 320.4 1497.3 122.4 0 S8 69 198.0 1497.3 122.4 0 S9 70 75.6 1497.3 122.4 0 S10 71 74.7 1497.3 150.3 0 S11 72 197.1 1497.3 122.4 0 S12 73 319.5 1497.3 122.4 0 S13 74 441.9 1497.3 122.4 0 S14 75 564.3 1497.3 122.4 0 S15 76 714.6 1497.3 150.3 0 S16 77 837.0 1497.3 122.4 0 S17 78 959.4 1497.3 122.4 0 S18 79 1081.8 1497.3 122.4 0 S19 80 1204.2 1497.3 122.4 0 Table 40. LCD segment output Alignment mark dimension and location of all PCA9620 types Coordinates X (m) Y (m) Location[1] 1495.8 1395.0 Dimension[2] 52.5 63.72 [1] The x/y coordinates of the alignment mark location represent the position of the REF point (see Figure 60) with respect to the center (x/y = 0) of the chip; see Figure 59. [2] The x/y values of the dimensions represent the extensions of the alignment mark in direction of the coordinate axis (see Figure 60). REF y x 013aaa511 Fig 60. Alignment mark PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 67 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 18. Packing information 18.1 Wafer information 18 m 18 m 70 m Saw lane Seal ring plus gap to active circuit ~18 mm 70 m detail X Pin 1 Straight edge of the wafer X Marking code 013aaa512 Wafer thickness, see Table 41. Fig 61. Wafer layout of PCA9620 PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 68 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial Table 41. PCA9620 Product data sheet PCA9620 wafer information Type number Wafer thickness Wafer diameter Marking of bad die PCA9620/5GA/Q1 0.687 mm 6 inch wafer mapping All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 69 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 19. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 "Surface mount reflow soldering description". 19.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 19.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: * Through-hole components * Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: * * * * * * Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 19.3 Wave soldering Key characteristics in wave soldering are: * Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave * Solder bath specifications, including temperature and impurities PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 70 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 19.4 Reflow soldering Key characteristics in reflow soldering are: * Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 62) than a SnPb process, thus reducing the process window * Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board * Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 42 and 43 Table 42. SnPb eutectic process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 43. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 62. PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 71 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 62. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 "Surface mount reflow soldering description". PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 72 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 20. Abbreviations Table 44. PCA9620 Product data sheet Abbreviations Acronym Description AEC Automotive Electronics Council CDM Charged-Device Model DC Direct Current EPROM Erasable Programmable Read-Only Memory ESD ElectroStatic Discharge HBM Human Body Model I2C Inter-Integrated Circuit bus IC Integrated Circuit LCD Liquid Crystal Display LSB Least Significant Bit MSB Most Significant Bit MSL Moisture Sensitivity Level MUX Multiplexer OTP One Time Programmable PCB Printed-Circuit Board POR Power-On Reset RC Resistance-Capacitance RAM Random Access Memory RMS Root Mean Square SCL Serial CLock line SDA Serial DAta line SMD Surface Mount Device All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 73 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 21. References [1] AN10365 -- Surface mount reflow soldering description [2] AN10706 -- Handling bare die [3] AN10853 -- ESD and EMC sensitivity of IC [4] AN11267 -- EMC and system level ESD design guidelines for LCD drivers [5] IEC 60134 -- Rating systems for electronic tubes and valves and analogous semiconductor devices [6] IEC 61340-5 -- Protection of electronic devices from electrostatic phenomena [7] IPC/JEDEC J-STD-020D -- Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices [8] JESD22-A114 -- Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM) [9] JESD22-C101 -- Field-Induced Charged-Device Model Test Method for Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components [10] JESD78 -- IC Latch-Up Test [11] JESD625-A -- Requirements for Handling Electrostatic-Discharge-Sensitive (ESDS) Devices [12] SNV-FA-01-02 -- Marking Formats Integrated Circuits [13] UM10204 -- I2C-bus specification and user manual [14] UM10569 -- Store and transport requirements PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 74 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 22. Revision history Table 45. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA9620 v.3 20130703 Product data sheet - PCA9620 v.2 Modifications: * Changed VLCD specification (Table 36) PCA9620 v.2 20111108 Product data sheet - PCA9620 v.1 PCA9620 v.1 20101209 Product data sheet - - PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 75 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 23. Legal information 23.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 23.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 23.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. PCA9620 Product data sheet Suitability for use in automotive applications -- This NXP Semiconductors product has been qualified for use in automotive applications. Unless otherwise agreed in writing, the product is not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 76 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Bare die -- All die are tested on compliance with their related technical specifications as stated in this data sheet up to the point of wafer sawing and are handled in accordance with the NXP Semiconductors storage and transportation conditions. If there are data sheet limits not guaranteed, these will be separately indicated in the data sheet. There are no post-packing tests performed on individual die or wafers. NXP Semiconductors has no control of third party procedures in the sawing, handling, packing or assembly of the die. Accordingly, NXP Semiconductors assumes no liability for device functionality or performance of the die or systems after third party sawing, handling, packing or assembly of the die. It is the responsibility of the customer to test and qualify their application in which the die is used. All die sales are conditioned upon and subject to the customer entering into a written die sale agreement with NXP Semiconductors through its legal department. 23.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of NXP B.V. 24. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 77 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 25. Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Ordering information . . . . . . . . . . . . . . . . . . . . .2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . .2 Marking codes . . . . . . . . . . . . . . . . . . . . . . . . . .2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .6 Commands of PCA9620 . . . . . . . . . . . . . . . . . .7 Initialize - initialize command bit description . . .8 OTP-refresh - OTP-refresh command bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Oscillator-ctrl - oscillator control command bit description . . . . . . . . . . . . . . . . . . . . . . . . . .8 Charge-pump-ctrl - charge pump control command bit description . . . . . . . . . . . . . . . . . .9 Temp-msr-ctrl - temperature measurement control command bit description . . . . . . . . . . . .9 Set-VPR-MSB - set VPR MSB command bit description . . . . . . . . . . . . . . . . . . . . . . . . . .9 Set-VPR-LSB - set VPR LSB command bit description . . . . . . . . . . . . . . . . . . . . . . . . .10 Display-enable - display enable command bit description . . . . . . . . . . . . . . . . . . . . . . . . .10 Set-MUX-mode - set multiplex drive mode command bit description . . . . . . . . . . . . . . . . .10 Set-bias-mode - set bias mode command bit description . . . . . . . . . . . . . . . . . . . . . . . . .10 Load-data-pointer - load data pointer command bit description . . . . . . . . . . . . . . . . . 11 Frame frequency - frame frequency and output clock frequency command bit description . . . . 11 Frame frequency values . . . . . . . . . . . . . . . . . 11 Input-bank-select - input bank select command bit description[1] . . . . . . . . . . . . . . . .12 Output-bank-select - output bank select command bit description[1] . . . . . . . . . . . . . . . .12 Write-RAM-data - write RAM data command bit description[1] . . . . . . . . . . . . . . . . . . . . . . . .13 Temp-read - temperature readout command bit description[1] . . . . . . . . . . . . . . . . . . . . . . . .13 Invmode_CPF_ctrl - inversion mode and charge pump frequency prescaler command bit description . . . . . . . . . . . . . . . . . . . . . . . . .13 Temp-filter - digital temperature filter command bit description . . . . . . . . . . . . . . . . .14 Selection of possible display configurations . . .15 Reset states . . . . . . . . . . . . . . . . . . . . . . . . . . .17 LCD drive modes: summary of characteristics .23 Parameters of VLCD generation . . . . . . . . . . . .33 Temperature measurement update rate . . . . .37 Temperature coefficients. . . . . . . . . . . . . . . . . .39 Calculation of the temperature compensated voltage VT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Mapping of output pins and corresponding output signals with respect to the multiplex driving mode . . . . . . . . . . . . . . . . . . . . . . . . . .41 I2C slave address . . . . . . . . . . . . . . . . . . . . . . .53 Control byte description . . . . . . . . . . . . . . . . . .54 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . .56 PCA9620 Product data sheet Table 36. Table 37. Table 38. Table 39. Table 40. Table 41. Table 42. Table 43. Table 44. Table 45. Static characteristics . . . . . . . . . . . . . . . . . . . . 57 Dynamic characteristics . . . . . . . . . . . . . . . . . 61 Dimensions of PCA9620 . . . . . . . . . . . . . . . . . 65 Bonding pad description of PCA9620 . . . . . . . 65 Alignment mark dimension and location of all PCA9620 types . . . . . . . . . . . . . . . . . . . . . . . . 67 PCA9620 wafer information . . . . . . . . . . . . . . . 69 SnPb eutectic process (from J-STD-020D) . . . 71 Lead-free process (from J-STD-020D) . . . . . . 71 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 73 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 75 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 78 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 26. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Fig 17. Fig 18. Fig 19. Fig 20. Fig 21. Fig 22. Fig 23. Fig 24. Fig 25. Fig 26. Block diagram of PCA9620 . . . . . . . . . . . . . . . . . .3 Pin configuration for LQFP80 (PCA9620H) . . . . . .4 Pin configuration for PCA9620U (bare die) . . . . . .5 Example of displays suitable for PCA9620 . . . . .15 Typical system configuration when using the internal VLCD generation . . . . . . . . . . . . . . . . . . .15 Typical system configuration when using an external VLCD . . . . . . . . . . . . . . . . . . . . . . . . .16 Recommended start-up sequence when using the internal charge pump and the internal clock signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Recommended start-up sequence when using an external supplied VLCD and the internal clock signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Recommended start-up sequence when using the internal charge pump and an external clock signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Recommended start-up sequence when using an external supplied VLCD and an external clock signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Recommended power-down sequence for minimum power-down current when using the internal charge pump and the internal clock signal . . . . . . . . . . .20 Recommended power-down sequence when using an external supplied VLCD and the internal clock signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Recommended power-down sequence when using the internal charge pump and an external clock signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Recommended power-down sequence when using an external supplied VLCD and an external clock signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Electro-optical characteristic: relative transmission curve of the liquid. . . . . . . . . . . . . . . . . . . . . . . . .24 Static drive mode waveforms (line inversion mode) . . . . . . . . . . . . . . . . . . . . . .25 Waveforms for the 1:2 multiplex drive mode with 12 bias (line inversion mode) . . . . . . . . . . . .26 Waveforms for the 1:2 multiplex drive mode with 13 bias (line inversion mode) . . . . . . . . . . . .27 Waveforms for the 1:4 multiplex drive mode with 13 bias (line inversion mode) . . . . . . . . . . . .28 Waveforms for 1:6 multiplex drive mode with 13 bias (line inversion mode) . . . . . . . . . . . .29 Waveforms for 1:6 multiplex drive mode with 14 bias (line inversion mode) . . . . . . . . . . . .30 Waveforms for 1:8 multiplex drive mode with 14 bias (line inversion mode) . . . . . . . . . . . .31 Waveforms for 1:8 multiplex drive mode with 14 bias (frame inversion mode) . . . . . . . . . .32 VLCD generation including temperature compensation . . . . . . . . . . . . . . . . . . . . . . . . . . .33 VLCD programming of PCA9620 (assuming VT[7:0] = 0h) . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Charge pump model (used to characterize the driving strength) . . . . . . . . . . . . . . . . . . . . . . . . . .35 PCA9620 Product data sheet Fig 27. Power efficiency of the charge pump . . . . . . . . . 36 Fig 28. Temperature measurement block with digital temperature filter . . . . . . . . . . . . . . . . . . . . . . . . . 37 Fig 29. Temperature measurement delay . . . . . . . . . . . . 38 Fig 30. Example of segmented temperature coefficients 39 Fig 31. Display RAM bitmap . . . . . . . . . . . . . . . . . . . . . . 43 Fig 32. Display RAM filling order in static drive mode . . . 44 Fig 33. Discarded bits and data pointer wrap around at the end of data transmission . . . . . . . . . . . . . . 45 Fig 34. Display RAM filling order in 1:2 multiplex drive mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Fig 35. Data pointer wrap around in 1:2 multiplex drive mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Fig 36. Display RAM filling order in 1:4 multiplex drive mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Fig 37. Data pointer wrap around in 1:4 multiplex drive mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Fig 38. Display RAM filling order in 1:6 multiplex drive mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Fig 39. Data pointer wrap around in 1:6 multiplex drive mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Fig 40. Display RAM filling order in 1:8 multiplex drive mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Fig 41. Data pointer wrap around in 1:8 multiplex drive mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Fig 42. Example of bank selection in 1:4 multiplex mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Fig 43. Example of the input-bank-select and the output-bank-select command with multiplex drive mode 1:4 . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Fig 44. Bit transfer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Fig 45. Definition of START and STOP conditions . . . . . 51 Fig 46. System configuration. . . . . . . . . . . . . . . . . . . . . . 52 Fig 47. Acknowledgement on the I2C-bus. . . . . . . . . . . . 52 Fig 48. I2C-bus protocol write mode . . . . . . . . . . . . . . . . 53 Fig 49. Control byte format . . . . . . . . . . . . . . . . . . . . . . . 54 Fig 50. I2C-bus protocol read mode . . . . . . . . . . . . . . . . 54 Fig 51. Device protection diagram . . . . . . . . . . . . . . . . . 55 Fig 52. Typical VLCD with respect to temperature . . . . . . 59 Fig 53. Typical IDD1 with respect to temperature . . . . . . . 59 Fig 54. Typical IDD2 with respect to temperature . . . . . . . 60 Fig 55. Typical ILCD with respect to temperature . . . . . . . 60 Fig 56. Driver timing waveforms . . . . . . . . . . . . . . . . . . . 62 Fig 57. I2C-bus timing waveforms . . . . . . . . . . . . . . . . . . 62 Fig 58. Package outline SOT315-1 (LQFP80) . . . . . . . . 63 Fig 59. Bare die outline of PCA9620. . . . . . . . . . . . . . . . 64 Fig 60. Alignment mark . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Fig 61. Wafer layout of PCA9620 . . . . . . . . . . . . . . . . . . 68 Fig 62. Temperature profiles for large and small components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 79 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 27. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 4.1 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 5 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 7.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 7.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6 8 Functional description . . . . . . . . . . . . . . . . . . . 7 8.1 Commands of PCA9620 . . . . . . . . . . . . . . . . . . 7 8.1.1 Command: initialize . . . . . . . . . . . . . . . . . . . . . 7 8.1.2 Command: OTP-refresh . . . . . . . . . . . . . . . . . . 8 8.1.3 Command: oscillator-ctrl . . . . . . . . . . . . . . . . . . 8 8.1.4 Command: charge-pump-ctrl . . . . . . . . . . . . . . 9 8.1.5 Command: temp-msr-ctrl . . . . . . . . . . . . . . . . . 9 8.1.6 Command: set-VPR-MSB and set-VPR-LSB . . 9 8.1.7 Command: display-enable . . . . . . . . . . . . . . . 10 8.1.8 Command: set-MUX-mode . . . . . . . . . . . . . . . 10 8.1.9 Command: set-bias-mode . . . . . . . . . . . . . . . 10 8.1.10 Command: load-data-pointer . . . . . . . . . . . . . 10 8.1.11 Command: frame-frequency . . . . . . . . . . . . . . 11 8.1.12 Bank select commands . . . . . . . . . . . . . . . . . 12 8.1.12.1 Command: input-bank-select . . . . . . . . . . . . . 12 8.1.12.2 Command: output-bank-select . . . . . . . . . . . . 12 8.1.13 Command: write-RAM-data . . . . . . . . . . . . . . 13 8.1.14 Command: temp-read. . . . . . . . . . . . . . . . . . . 13 8.1.15 Command: invmode_CPF_ctrl . . . . . . . . . . . . 13 8.1.16 Command: temp-filter . . . . . . . . . . . . . . . . . . . 14 8.2 Possible display configurations . . . . . . . . . . . 14 8.3 Start-up and shut-down. . . . . . . . . . . . . . . . . . 16 8.3.1 Power-On Reset (POR) . . . . . . . . . . . . . . . . . 16 8.3.2 Recommended start-up sequences . . . . . . . . 18 8.3.3 Recommended power-down sequences . . . . 20 8.4 LCD voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 22 8.4.1 LCD voltage selector . . . . . . . . . . . . . . . . . . . 22 8.4.1.1 Electro-optical performance . . . . . . . . . . . . . . 24 8.4.2 LCD drive mode waveforms . . . . . . . . . . . . . . 25 8.4.2.1 Static drive mode . . . . . . . . . . . . . . . . . . . . . . 25 8.4.2.2 1:2 Multiplex drive mode. . . . . . . . . . . . . . . . . 26 8.4.2.3 1:4 Multiplex drive mode. . . . . . . . . . . . . . . . . 28 8.4.2.4 1:6 Multiplex drive mode. . . . . . . . . . . . . . . . . 29 8.4.2.5 1:8 Multiplex drive mode. . . . . . . . . . . . . . . . . 31 8.4.3 VLCD generation . . . . . . . . . . . . . . . . . . . . . . . 33 8.4.4 External VLCD supply . . . . . . . . . . . . . . . . . . . 34 8.4.5 8.4.6 8.4.7 8.4.8 8.5 8.5.1 8.5.2 8.5.3 8.6 8.7 8.8 8.9 8.9.1 8.9.1.1 8.9.1.2 8.9.1.3 8.9.1.4 8.9.1.5 8.9.2 8.9.2.1 8.9.2.2 9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 10 11 12 13 14 15 15.1 16 17 18 18.1 19 19.1 19.2 19.3 Charge pump driving capability . . . . . . . . . . . Charge pump frequency settings and power efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature readout . . . . . . . . . . . . . . . . . . . Temperature compensation of VLCD . . . . . . . . Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal oscillator . . . . . . . . . . . . . . . . . . . . . . External clock. . . . . . . . . . . . . . . . . . . . . . . . . Timing and frame frequency . . . . . . . . . . . . . Backplane outputs . . . . . . . . . . . . . . . . . . . . . Segment outputs . . . . . . . . . . . . . . . . . . . . . . Display register . . . . . . . . . . . . . . . . . . . . . . . Display RAM . . . . . . . . . . . . . . . . . . . . . . . . . Data pointer . . . . . . . . . . . . . . . . . . . . . . . . . . RAM filling in static drive mode . . . . . . . . . . . RAM filling in 1:2 multiplex drive mode . . . . . RAM filling in 1:4 multiplex drive mode . . . . . RAM filling in 1:6 multiplex drive mode . . . . . RAM filling in 1:8 multiplex drive mode . . . . . Bank selection . . . . . . . . . . . . . . . . . . . . . . . . Input-bank-select . . . . . . . . . . . . . . . . . . . . . . Output-bank-select. . . . . . . . . . . . . . . . . . . . . I2C-bus interface characteristics . . . . . . . . . . Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . START and STOP conditions. . . . . . . . . . . . . System configuration . . . . . . . . . . . . . . . . . . . Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . I2C-bus controller . . . . . . . . . . . . . . . . . . . . . . Input filters . . . . . . . . . . . . . . . . . . . . . . . . . . . I2C-bus slave address . . . . . . . . . . . . . . . . . . I2C-bus protocol . . . . . . . . . . . . . . . . . . . . . . . Internal circuitry . . . . . . . . . . . . . . . . . . . . . . . Safety notes. . . . . . . . . . . . . . . . . . . . . . . . . . . Limiting values . . . . . . . . . . . . . . . . . . . . . . . . Static characteristics . . . . . . . . . . . . . . . . . . . Dynamic characteristics. . . . . . . . . . . . . . . . . Test information . . . . . . . . . . . . . . . . . . . . . . . Quality information . . . . . . . . . . . . . . . . . . . . . Package outline. . . . . . . . . . . . . . . . . . . . . . . . Bare die outline . . . . . . . . . . . . . . . . . . . . . . . . Packing information . . . . . . . . . . . . . . . . . . . . Wafer information. . . . . . . . . . . . . . . . . . . . . . Soldering of SMD packages . . . . . . . . . . . . . . Introduction to soldering. . . . . . . . . . . . . . . . . Wave and reflow soldering. . . . . . . . . . . . . . . Wave soldering . . . . . . . . . . . . . . . . . . . . . . . 35 35 37 38 40 40 40 41 41 42 42 42 43 44 45 45 46 47 48 49 50 51 51 51 51 52 53 53 53 53 55 55 56 57 61 62 62 63 64 68 68 70 70 70 70 continued >> PCA9620 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 3 July 2013 (c) NXP B.V. 2013. All rights reserved. 80 of 81 PCA9620 NXP Semiconductors 60 x 8 LCD high-drive segment driver for automotive and industrial 19.4 20 21 22 23 23.1 23.2 23.3 23.4 24 25 26 27 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . . Legal information. . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information. . . . . . . . . . . . . . . . . . . . . Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 73 74 75 76 76 76 76 77 77 78 79 80 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2013. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 3 July 2013 Document identifier: PCA9620