13C2000PA4K - Honeywell

Pressure Sensors

Low-cost, Stainless Steel, Isolated Sensors 13 mm Series

Sensing and Control

FEATURES

• Rugged, isolated stainless

steel package

• Reliable semiconductor

technology

• Calibrated and

temperature compensated

• Voltage or current supply

options

• Absolute and sealed gage

pressures

• Low-cost cell package

• Absolute pressure

• 0 psi to 500 psi, 1000 psi,

2000 psi, 3000 psi, and

5000 psi

TYPICAL APPLICATIONS

• Industrial controls

• Hydraulic controls

• Tank pressure

• Pressure transmitters

• Process control systems

WARNING

PERSONAL INJURY

DO NOT USE these

products as safety or

emergency stop devices or

in any other application

where failure of the product

could result in personal

injury.

Failure to comply with

these instructions could

result in death or serious

injury.

Honeywell’s 13 mm Series stainless steel pressure sensors are designed

for high pressure applications that involve measurement of hostile media in

harsh environments. This series uses Honeywell’s proven piezoresistive

semiconductor sensor chip in an oil-isolated housing with or without an

integral ceramic for temperature compensation and calibration. This design

has proven to be highly reliable, stable and accurate.

These sensors feature a weld-ring collar and special back support ring for

high cycle life capability as they are designed for further package integration

in OEM (Original Equipment Manufacturer) applications. Products are

available with pressure ranges from 500 psi through 5000 psi and can be

used with voltage or current supplies.

EQUIVALENT CIRCUIT

13 mm compensated series 13 mm uncompensated series

WARNING

MISUSE OF DOCUMENTATION

• The information presented in this product sheet is for reference only. Do

not use this document as a product installation guide.

• Complete installation, operation, and maintenance information is provided

in the instructions supplied with each product.

Failure to comply with these instructions could result in death or

serious injury.

Pressure Sensors

Low-cost, Stainless Steel, Isolated Sensors 13 mm Series

2 Honeywell • Sensing and Control

PRESSURE SENSOR CHARACTERISTICS (all devices)

Environmental specifications

Compensated temperature range 0 °C to 82 °C [32 °F to 180 °F]

Operating temperature range -40 °C to 125 °C [-40 °F to 257 °F]

Storage temperature range -40 °C to 125 °C [-40 °F to 257 °F]

Vibration 10 G at 20 Hz to 2000 Hz

Shock 100 G for 11 ms

Life 1 million cycles min.

Insulation resistance 100 mΩ at 50 Vdc

Maximum ratings

Voltage version “K” Supply voltage VS = +15 Vdc

Voltage version “L” Supply current IS = +2.0 mA

PERFORMANCE CHARACTERISTICS – COMPENSATED SERIES (1)

Characteristic Minimum Typical Maximum Units

Zero pressure offset -2 0 +2 mV

Pressure non-linearity (3) – ±0.1 ±0.25 %FSS

Pressure hysteresis (3) – ±0.015 ±0.030 %FSS

Repeatability – ±0.010 ±0.030 %FSS

Temp. effect on span (4) – ±0.5 ±1.0 %FSS

Temp. effect on offset (4) – ±0.5 ±1.0 %FSS

Thermal hysteresis (0 °C to 82 °C [32 °F to 180 °F]) – ±0.1 ±0.3 %FSS

Long-term stability of offset and span (5) – ±0.1 ±0.3 %FSS

Response time (6) – 0.1 – ms

Common mode voltage (voltage version “K”) (9) 0.50 1.25 2.0 Vdc

Input resistance (current version “L”) 2.0 4.5 8.0 kΩ

Input resistance (voltage version “K”) 8.0 25 50 kΩ

Output resistance 3.0 4.5 6.0 kΩ

PRESSURE RANGE SPECIFICATIONS – COMPENSATED SERIES

Catalog Listing Pressure range Full scale span (2) Proof pressure

(7) Burst pressure

(8)

13C 0500P (A,S) (1,4,5,6) (K,L) 0 psi to 500 psi 98 mV to 102 mV 1500 psi 2500 psi

13C 1000P (A,S) (1,4,5,6) (K,L) 0 psi to 1000 psi 98 mV to 102 mV 3000 psi 5000 psi

13C 2000P (A,S) (1,4,5,6) (K,L) 0 psi to 2000 psi 98 mV to 102 mV 6000 psi 10,000 psi

13C 3000P (A,S) (1,4,5,6) (K,L) 0 psi to 3000 psi 98 mV to 102 mV 9000 psi 10,000 psi

13C 5000P (A,S) (1,4,5,6) (K,L) 0 psi to 5000 psi 148 mV to 152 mV 10,000 psi 10,000 psi

NOTES

1. Reference conditions (unless otherwise noted): TA = 25 °C [77 °F]; Supply VS = 10 Vdc ±0.01 Vdc or IS = 1.5 mA

±0.0015 mA.

2. Full-scale span (FSS) is the algebraic difference between the output voltage at full-scale pressure and the output at zero

pressure. FSS is ratiometric to supply voltage.

3. Pressure non-linearity is based on best-fit straight line from zero to the full-scale pressure. Pressure hysteresis is the

maximum output difference at any point within the operating pressure range for increasing and decreasing pressure.

4. Maximum error band of the offset voltage or span over the compensated temperature range, relative to the 25 °C [77 °F]

reading.

5. Long-term stability over a six-month period.

6. Response time for a 0 psi to FSS pressure step change, 10 % to 90 % rise time.

7. The maximum pressure that can be applied without changing the transducer’s performance or accuracy.

8. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer

case.

9. Common mode voltage as measure from output to ground.

Pressure Sensors

Low-cost, Stainless Steel, Isolated Sensors 13 mm Series

Honeywell • Sensing and Control 3

PERFORMANCE CHARACTERISTICS – UNCOMPENSATED SERIES (1)

Characteristic Minimum Typical Maximum Unit

Zero pressure offset -7.5 0 +7.5 mV/V

Pressure non-linearity (3) – ±0.1 ±0.25 %FSS

Pressure hysteresis (3) – ±0.015 ±0.030 %FSS

Repeatability – ±0.010 ±0.030 %FSS

Temp. coefficient of span (4)

(0 °C to 82 °C [32 °F to 180 °F])

360 720 1260 ppm/°C

Temp. coefficient of resistance (4)

(0 °C to 82 °C [32 °F to 180 °F])

2700 3420 4500 ppm/°C

Temp. coefficient of offset (4)

(0 °C to 82 °C [32 °F to 180 °F])

– 30 – µV/V/°C

Thermal hysteresis

(0 °C to 82 °C [32 °F to 180 °F])

– ±0.1 ±0.3 %FSS

Long-term stability of offset and span (5) – ±0.1 ±0.3 %FSS

Response time (6) – 0.1 – ms

Input resistance 4.0 4.75 6.0 kΩ

Output resistance 4.0 4.75 6.0 kΩ

PRESSURE RANGE SPECIFICATIONS – UNCOMPENSATED SERIES

Catalog Listing Pressure range Full scale span (2) Proof pressure

(7) Burst pressure

(8)

13U 0500P A 0 K 0 psi to 500 psi 175 mV to 300 mV 1200 psi 2400 psi

13U 1000P A 0 K 0 psi to 1000 psi 175 mV to 300 mV 3000 psi 5000 psi

13U 2000P A 0 K 0 psi to 2000 psi 175 mV to 300 mV 6000 psi 10,000 psi

13U 3000P A 0 K 0 psi to 3000 psi 175 mV to 300 mV 9000 psi 10,000 psi

13U 5000P A 0 K 0 psi to 5000 psi 290 mV to 500 mV 10,000 psi 10,000 psi

NOTES

1. Reference conditions (unless otherwise noted): TA = 25 °C [77 °F]; Supply VS = 10 Vdc ±0.01 Vdc or IS = 1.5 mA

±0.0015 mA.

2. Full-scale span (FSS) is the algebraic difference between the output voltage at full-scale pressure and the output at zero

pressure. FSS is ratiometric to supply voltage.

3. Pressure non-linearity is based on best-fit straight line from zero to the full-scale pressure. Pressure hysteresis is the

maximum output difference at any point within the operating pressure range for increasing and decreasing pressure.

4. The error band resulting from maximum deviation of a transducer’s output parameter (offset, span, or resistance) as

temperature is varied from 25 °C [77 °F] to any other temperature within the specified range 0 °C to 82 °C [32 °F to

180 °F]. This parameter is not 100 % tested and is guaranteed by process design and tested on a sample basis only.

Temperature coefficient of span is evaluated using a constant current source.

5. Long-term stability over a six-month period.

6. Response time for a 0 psi to FSS pressure step change, 10 % to 90 % rise time.

7. The maximum pressure that can be applied without changing the transducer’s performance or accuracy.

8. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer

case.

Pressure Sensors

Low-cost, Stainless Steel, Isolated Sensors 13 mm Series

4 Honeywell • Sensing and Control

PHYSICAL DIMENSIONS for reference only, in (mm)

Package 1 (see note): Ring with back support

Note: Non-concentricity effects at the diaphragm weld area may cause runout of up to ±0.006 in between the upper and

lower portions of the sensor body. (It is recommended to use a counter bore to mate with this device to allow for this non-

concentricity).

Package 4: 1/8-27 NPT

Pressure Sensors

Low-cost, Stainless Steel, Isolated Sensors 13 mm Series

Honeywell • Sensing and Control 5

Package 5: 1/4-18 NPT

Package 6: 7/16-20 UNF

Pressure Sensors

Low-cost, Stainless Steel, Isolated Sensors 13 mm Series

6 Honeywell • Sensing and Control

Package 0 (see note): Ring and cell

Note: Non-concentricity effects at the diaphragm weld area may cause runout of up to ±0.006 in between the upper and

lower portions of the sensor body. (It is recommended to use a counter bore to mate with this device to allow for this non-

concentricity).

Pressure Sensors

Low-Cost, Stainless Steel, Isolated Sensors 13 mm Series

Honeywell • Sensing and Control 7

ORDERING INFORMATION

13 mm Compensated Series

For example: Part #13C3000PS4K = 13 mm Cell, Compensated, 3000 psi, Sealed Gauge, 1/8NPT Port with 10 Vdc

excitation.

13 mm Uncompensated Series

Pressure Sensors

Low-cost, Stainless Steel, Isolated Sensors 13 mm Series

Sensing and Control

www.honeywell.com/sensing

Honeywell

11 West Spring Street

Freeport, Illinois 61032

008131-1-EN IL50 GLO 1004 Printed in USA

WARRANTY/REMEDY

Honeywell warrants goods of its manufacture as

being free of defective materials and faulty

workmanship. Contact your local sales office for

warranty information. If warranted goods are returned

to Honeywell during the period of coverage,

Honeywell will repair or replace without charge those

items it finds defective. The foregoing is Buyer’s

sole remedy and is in lieu of all other warranties,

expressed or implied, including those of

merchantability and fitness for a particular

purpose.

Specifications may change without notice. The

information we supply is believed to be accurate and

reliable as of this printing. However, we assume no

responsibility for its use.

While we provide application assistance personally,

through our literature and the Honeywell web site, it

is up to the customer to determine the suitability of

the product in the application. For application

assistance, current specifications, or name of the

nearest Authorized Distributor, contact a nearby

sales office. Or call:

1-800-537-6945 USA/Canada

1-815-235-6847 International

FAX

1-815-235-6545 USA

INTERNET

www.honeywell.com/sensing

info.sc@honeywell.com