MS3471W20-41SY - ITT Cannon

www.ittcannon.com 157

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

Military Specification Cross Reference

PV7 and MIL-C-26482

(Series 2) Replacement for

MIL-C-26482 (Series 1)

MS3110,MS3120

MS3111,MS3121

MS3112,MS3122

MS3114,MS3124

MS3116,MS3126

MS3470

MS3471

MS3470

MS3474

MS3476

MS3472

MS3475

PV70

PV71

PV70

PV74

PV76

PV72

PV75

/1

/7

/1

/5

/13

/3

/43

/1

/3

/5

/13

/2

/8

/12

/6

/14

/4

/42

Narrow Flange Receptacle

Cable Connecting Receptacle

Narrow Flange Receptacle

Jam Nut Receptacle

Straight Plug

Wide Flange Receptacle

Straight Plug, RFI Shielded

Narrow Flange Receptacle

Wide Flange Receptacle

Jam Nut Receptacle

Straight Plug

/2

/4

/6

/14

MS3470

MS3472

MS3474

MS3476

NAS1650,NAS1699

NAS1651,NAS1700

NAS1652,NAS1701

NAS1653,NAS1702

*NOTE: M83723 series has been superseded by MIL-C-26482 Series 2.

MIL-C-26482 Socket Pin

NAS1599

MIL-C-83723*

Slash Sheet

ITT Cannon Prefix

Commercial

DesignMS Standards Description

• Intermatable with MIL-C-26482 Series I

• Operating termperature - 55˚C to + 200˚C

The PV connector is designed to meet the rugged

requirements of MIL-C-26482, Series 2/MIL-C-83723

Series I*, the specification which delineates

the critical requirements of space-age applications. PV

connectors have been used extensively on major

aerospace programs requiring general-purpose,

miniature cylindrical bayonet coupling connectors

such as Space Shuttle, Apollo, ATM, OWS Min-

uteman, Skylab, Thor-Delta, Titan IIIC, and Viking.

The PV series is an important member of the

Universal Interconnect System (UIS) - the only

system that can perform all interconnection mis-

sions. This system is adaptable for use with connec-

tors of all shapes and sizes, including circular and

rectangular configurations. standard, miniature and

subminiature sizes. UIS is a rear servicing system

that evolved from the LITTLE CAESAR® rear re-

lease contact retention assembly, pioneered and

developed by ITT Cannon. Since this time,

ITT Cannon, and its licensees, have supplied to

industry over 250 million interconnections utilizing

this system.

PV7 connectors are available under numerous in-

dustrial specifications, some of which are listed

below:

• CS512089 Jet Propulsion Laboratory

• 40M39569 NASA, George C. Marshall Space

Flight Center

• 81D52 Martin Marietta, Denver Division

• MG414-0365 Rockwell International Space

Division

• AC414-0013 Rockwell International Autonetics

Division

• STS0003 McDonnell Douglas Astronautics

This connector series is manufactured to accommo-

date the following backshells: M85049/31

(MS3416), M85049/51 (MS3418) and M85049/

52 (MS3417). Backshells are not included with

connector and must be ordered separately. Back-

shells on page 161 are Non-MS type.

Universal Insertion / Extraction Tool Style - A

single,expendable plastic tool is used for insertion and

extraction of both pins and sockets.

Simple, Strong Contact Design - One basic config-

uration eliminates undercuts and maximizes bend re-

sistance for positive contact mating.

Closed-Entry Socket Insert - Hard dielectric socket

face of mating connector has lead-in chamfers for

positive alignment of pins and sockets.

Interfacial Pin Insert Seal - Universal interconnect

permits design of raised moisture barriers around each

pin which mate into lead-in chambers of hard face

sockets insert for individual contact sealing. Interfacial

sealing is never touched by service tools.

Superior Contact Stability - Rear Contact Release

System (LITTLE CAESAR contact assembly) features a

stamped metal retaining clip captivated by molded-in

shoulders of each contact cavity in the insulator. A

rear-inserted plastic tool expands the tines beyond the

contact shoulder, releasing the contact.

Polarized Backshells - Interlocking teeth on the front of the

backshell and rear portion of the shell allow

endbells to be positioned as desired, eliminating chaf-

ing of wire during assembly.

3

2

4 1

www.ittcannon.com 158

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

How to Order

Performance and Material Specifications

ELECTRICAL

MATERIALS AND FINISHES

Description

Shell Aluminum alloy per QQ-A-367, QQ-A-591 or QQ-A-225 Electoless nickel per MIL-C-26074, anodized per MIL-A-8625 or olive drab

cadmium over nickel

Electoless nickel per MIL-C-26074, anodized per MIL-A-8625 or olive drab

cadmium over nickel

Electoless nickel per MIL-C-26074, anodized per MIL-A-8625 or olive drab

cadmium over nickel

Insulators Rigid dielectric

Silicone rubber (ITT Cannon blend) or Fluorosiclicone rubber (ITT

Cannon blen)

Copper alloy

Aluminum alloy per QQ-A-591

Aluminum alloy per QQ-A-225

None

Gold page per MIL-G-45204

Elastomers (grommets, interfacial and O ring seals)

Contacts

Coupling Nut

Jam Nut (on PV74)

12

16

20

.097 (2.46)

.053 (1.53)

.040 (1.02)

.158 (4.01)

.103 (2.62)

.083 (2.11)

12

14

16

20

24

I

II

1500 Vac rms

2300 Vac rms

375 Vac rms

500 Vac rms

5000 megohms minimum

23

17

13

7.5

3.0

50

45

50

45

55

45

Contact

Size Wire

Size Max Current

for Test (amps) Potential Drop

(Millivolts at 25˚C)

Insulation O.D. Limits, inch (mm)

min. max.

Service Rating Sea Level

SERIES PREFIX

PV

MS 70

3470 L

L18

18 -32

-32 P

PW

WL

SHELL STYLE

CLASS

SIZE

CONTACT ARRANGEMENT

CONTACT TYPE

ALTERNATE INSERT POSITIONS

LESS COMPONENTS

CLASS

SHELL SIZE

SHELL STYLE

SERIES PREFIX

MS - Complies with MIL-C-26482 Series 2

PV - ITT Cannon Interchangeable with

MIL-C-26482, Series 2

*Consult factory for availablility.

(PV Series and MS Series)

*A - Fluid resistant, 200˚C, non-conductive

(anodized)

L - Fluid resistant, 200˚C, conductive, finish

(nickely)

W - Corrosive and fluid resistant, 175˚C

(cadmium over nickel)

P - Pin contact

S - Socket contact

A - Less pin contact* (MS only)

B - Less socket contacts* (MS only)

No designation required for normal posistion.

Standard MS alternate positions available.

Use "L" if PV connectors are ordered less

contacts, sealing plugs and insertion/extraction

tool ("L" is not stamped on connectors). To

order MS connectors less contacts, purchase

order must state less contacts.

* The "A" and "B" designators are used only when other

than power contacts are ato be installed (i.e. shielded, coaxial

and thermocouple contacts).

8, 10, 12, 14, 16, 18, 20, 22 and 24

(Size 8 avialable in PV70 & 76 only)

See page 162.

ITT Cannon

Part No.

PV70

PV71

PV72

PV74

PV75

PV76

MS3470

MS3471

MS3472

MS3474

MS3475

MS3476

- Narrow Flange Receptacle

- Cable Connecting Receptacle

- Wide Flange Receptacle

- Jam Nut Receptacle

- Straight Plug, RFI Shielded

- Straight Plug

Military No. Description

CONTACT TYPE

ALTERNATE INSERT POSITIONS

LESS COMPONENTS

CONTACT ARRANGEMENTS

70,000 ft. Altitude (25˚C)

Dielectric Withstanding Voltage (Test Volatge)

Material Finish

www.ittcannon.com 159

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

Narrow Flange Receptacle

Cable Connecting Receptacle

MS3470 PV70

MS3471 PV71

Shell

Size*

8

10

12

14

16

18

20

22

24

.462 (11.73)

.587 (14.91)

.620 (15.75)

.474 (12.04)

.594 (15.01)

.751 (19.08)

.876 (22.25)

1.001 (25.43)

1.126 (28.60)

1.251 (31.78)

1.376 (34.95)

1.501 (38.13)

1.215 (30.85)

1.275 (32.40)

.078 (1.98)

.110 (2.79)

.594 (15.09)

.719 (18.26)

.812 (20.62)

.906 (23.01)

.969 (24.61)

1.062 (26.97)

1.156 (29.36)

1.250 (31.75)

1.375 (34.93)

.828 (21.03)

.954 (24.23)

1.047 (26.59)

1.141 (28.98)

1.234 (31.34)

1.328 (33.73)

1.453 (36.91)

1.578 (40.08)

1.703 (43.26)

1/2-20

5/8-24

3/4-20

7/8-20

1-20

1-1/16-18

1-3/16-18

1-5/16-18

1-7/16-18

10

12

14

16

18

20

22

24

10

12

14

16

18

20

22

24

*See page 158 for part numbers.† To order backshell assemblies separately, see page 161.

1.492 (37.90)

1.552 (39.42)

.286 (7.26)

.416 (10.57)

.476 (12.09)

.626 (15.90)

.706 (17.93)

.831 (21.11)

.956 (24.28)

1.081 (27.46)

.286 (7.26)

.416 (10.57)

.476 (12.09)

.626 (15.90)

.706 (17.93)

.831 (21.11)

.956 (24.28)

1.081 (27.46)

1.842 (46.79)

2.077 (52.76)

2.137 (54.28)

.880 (23.35)

.950 (24.13)

1.010 (25.65)

1.070 (27.18)

1.130 (28.70)

1.190 (30.23)

1.260 (32.00)

1.320 (33.53)

2.115 (53.72)

2.250 (57.15)

2.340 (59.44)

2.475 (62.87)

2.574 (65.38)

2.767 (70.28)

2.890 (73.41)

3.012 (76.50)

.462 (11.73)

.587 (14.91)

.620 (15.75)

.591 (15.01)

.751 (19.08)

.876 (22.25)

1.001 (25.43)

1.126 (28.60)

1.251 (31.78)

1.376 (34.95)

1.501 (38.13)

.078 (1.98)

.110 (2.79)

1.082 (27.48)

1.176 (29.87)

1.270 (32.26)

1.364 (34.64)

1.458 (37.03)

1.708 (43.38)

1.832 (46.53)

.954 (24.23)

1.047 (26.59)

1.141 (28.98)

1.234 (31.34)

1.328 (33.73)

1.578 (40.08)

1.703 (43.26)

1.215 (30.86)

1.275 (32.38)

5/8-24

3/4-20

7/8-20

1-20

1-1/16-18

1-5/16-18

1-7/16-18

4 HOLES .125/.115 (3.18/2.92) DIA. SIZES 10-22

.152/.142/(3.86/3.61) DIA SIZE 24 ONLY

POLARIZING

GROOVE

L

(TYP)

F

DIA

BU THD

J

G

.130/.190

(3.30/4.83)

POLARIZING

GROOVE R DIA.

MAX.

S MAX.

(TYP.)

EC REF. ES REF.

ER REF.

GR

REF.

HR

FS

B

JV THD

A

DIA.

W.130/.190

(3.30/4.83)

K

(TYP)

(TP)

.140 RAD.

MAX.

B

Max F

Max G

Max J

Max

U Thread

UNEF

Class 2AK L

Shell

Size*

Shell

Size*

TYPE R

TYPE STYPE C

Backshell Assemblies not supplied with MS connectors.

Perfomance Specifications - Page 158

Contacts, Sealing Plugs, Assembly Tools - Pages

163, 165

Contacts Arrangements - Page 162

Fs

Max. Es

Max. Gr

Max. Hr

Max. Er

Max.

TYPE C

Ec

Max.

TYPE S TYPE R

Receptacle Assembly With Backshell†

A

Max B

Max J

Max R Dia.

Max S

Max W

Max

U Thread

UNEF

Class 2A

www.ittcannon.com 160

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

Wide Flange Receptacle

MS3472 PV72

Shell

Size*

10

12

14

16

18

20

22

24

.591 (15.01)

.751 (19.08)

.876 (22.25)

1.001 (25.43)

1.126 (28.60)

1.251 (31.78)

1.376 (34.95)

1.501 (38.13)

.493 (12.52)

.587 (14.91)

.620 (15.75)

1.215 (30.85)

1.275 (32.40)

.078 (1.98)

.110 (1.98)

.812 (20.62)

.938 (23.83)

1.031 (26.19)

1.125 (28.58)

1.203 (30.56)

1.297 (32.94)

1.375 (34.93)

1.500 (38.10)

1.141 (28.98)

1.266 (32.16)

1.360 (34.54)

1.453 (36.91)

1.532 (38.91)

1.688 (42.88)

1.766 (44.86)

1.891 (48.03)

5/8-24

3/4-20

7/8-20

1-20

1-1/16-18

1-3/16-18

1-5/16-18

1-7/16-18

Shell

Size* V

Max. A

Max. B

Max. F

Max. G

Max. H

Max.

POLARIZING

GROOVE

POLARIZING

GROOVE

Q

(TYP)

H (TP)

.140 RAD.

MAX.

4 HOLES .150 +_ .005

(3.81 +_ 0.13mm)

DIA. B

A

DIA.

P THD.

G

F

.130/.190

(3.30/4.83)

V

A

W

F

DIA.

GHB

GG

L THD.

.130/.190

(3.30/4.83)

GG

Panel

Thickness

W

Dia.

Max.

L Thread

UNEF

Class 2

8

10

12

14

16

18

20

22

24

Shell

Size*

Receptacle Assembly With Backshell†

* See page 158 for part numbers. † To order backshell assemblies separately, see page 161.

BBs

Max. Fs

Max. BBR

Max.

BBC REF.

TYPE C TYPE S TYPE R

Backshell Assemblies not supplied with MS connectors.

Performance Specifications - Page 158

Contacts, Sealing Pluts, Assembly Tools - Pages

163, 165

Contact Arrangments - Page 162

BBS REF. BBR REF.

GR

REF.

HR

FS

GR

Max. HR

Max.

TYPE C

BBc

Max.

TYPE S TYPE R

10

12

14

16

18

20

22

24

1.492 (37.90)

1.552 (39.42)

.954 (24.23)

1.078 (27.38)

1.266 (32.16)

1.391 (35.33)

1.516 (38.51)

1.641 (41.68)

1.828 (46.43)

1.954 (49.63)

2.078 (52.78)

.767 (19.48)

.892 (22.66)

1.079 (27.41)

1.205 (30.61)

1.329 (33.76)

1.455 (36.96)

1.579 (40.11)

1.705 (40.11)

1.829 (46.46)

.113 (2.87)

.148 (3.76)

.474 (12.04)

.591 (15.01)

.751 (19.08)

.876 (22.25)

1.001 (25.43)

1.126 (28.60)

1.251 (31.78)

1.376 (34.95)

1.501 (38.13)

.707 (17.96)

.772 (19.61)

.187/.062 (4.75/1.57)

.250/.062 (6.35/1.57)

.219/.062 (5.56/1.57)

1.215 (30.86)

1.215 (30.85)

1.275 (32.40)

1.078 (27.38)

1.203 (30.56)

1.391 (35.33)

1.516 (38.51)

1.641 (41.68)

1.766 (44.86)

1.954 (49.63)

2.078 (52.78)

2.203 (55.96)

1/2-20

5/8-24

3/4-20

7/8-20

1-20

1-1/16-18

1-3/16-18

1-5/16-18

1-7/16-18

1.842 (46.79)

2.077 (52.76)

2.137 (54.28)

.286 (7.26)

.416 (10.57)

.476 (12.09)

.626 (15.90)

.706 (17.93)

.831 (21.11)

.956 (24.28)

1.081 (27.46)

2.115 (53.72)

2.250 (57.15)

2.340 (59.44)

2.475 (62.87)

2.574 (65.38)

2.767 (70.28)

2.890 (73.41)

3.012 (76.50)

.880 (22.35)

.950 (24.13)

1.010 (25.65)

1.070 (27.18)

1.130 (28.70)

1.190 (30.23)

1.260 (32.00)

1.320 (33.53)

.286 (7.26)

.416 (10.57)

.476 (12.09)

.626 (15.90)

.706 (17.93)

.831 (21.11)

.956 (24.28)

1.081 (27.46)

A

Max. B

Max. F

Max. G

Max. H

Max. Q

Max.

P Thread

UNEF

Class A

Jam Nut Receptacle

MS3474 PV74

www.ittcannon.com 161

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

Straight Plug

Backshells (Non-MS)

MS3476 PV76

Shell

Size* A Dia.

Max. U

Max. W

Max. E Thread

UNEF Class 2A

8

10

12

14

16

18

20

22

24

Shell

Size* E Thread

UNEF Class 2A A Dia.

Max. U

Max. W

Max.

10

12

14

16

18

20

22

24

Shell

Size*

TYPE C

VC

Max. FS

Max. VS

Max. GR

Max. HR

Max. VR

Max.

TYPE S TYPE R

8

10

12

14

16

18

20

22

24

Shell

Size*

ITT CANNON

Conductive

(Nickel finish)

TYPE C (SHORT) TYPE S (Straight) TYPE R (90˚)

ITT CANNON

Conductive

(Nickel finish)

ITT CANNON

Conductive

(Nickel finish)

10

12

14

16

18

20

22

24

057-0716-002

057-0717-002

057-0718-002

057-0719-002

057-0720-002

057-0721-002

057-0722-002

057-0723-002

057-0683-002

057-0684-002

057-0685-002

057-0686-002

057-0687-002

057-0688-002

057-0689-002

057-0731-002

057-0704-001

057-0705-001

057-0706-001

057-0707-001

057-0708-001

057-0709-001

057-0710-001

057-0711-001

1.507 (38.28)

.286 (7.26)

.416 (10.57)

.476 (12.09)

.626 (15.90)

.706 (17.93)

.831 (21.11)

.956 (24.28)

1.081 (27.46)

.286 (7.26)

.416 (10.57)

.476 (12.09)

.626 (15.90)

.706 (17.93)

.831 (21.11)

.956 (24.28)

1.081 (27.46)

2.130 (54.10)

2.265 (57.53)

2.355 (59.82)

2.490 (63.25)

2.589 (65.76)

2.722 (69.14)

2.845 (72.26)

2.967 (75.36)

1.857 (47.17)

2.092 (53.14)

2.092 (52.14)

.880 (22.35)

.950 (24.13)

1.010 (25.65)

1.070 (27.18)

1.130 (28.70)

1.190 (30.23)

1.260 (32.00)

1.320 (33.53)

5/8-24

3/4-20

7/8-20

1-20

1-1/16-18

1-3/16-18

1-5/16-18

1-7/16-18

* See page 158 for part numbers.

* See page 158 for part numbers. † To order backshell assemblies separatedly, see page 161.

.840 (21.34)

.999 (25.37)

1.139 (28.93)

1.261 (32.03)

1.337 (33.96)

1.477 (37.52)

1.602 (40.69)

1.723 (43.76)

.926 (21.72)

1.043 (26.42)

1.183 (29.97)

1.305 (33.15)

1.391 (35.33)

1.531 (38.89)

1.656 (42.06)

1.777 (45.14)

1.230 (31.24)

.765 (19.43)

.840 (21.34)

.999 (25.37)

1.139 (28.93)

1.261 (32.03)

1.337 (33.96)

1.477 (37.52)

1.602 (40.69)

1.723 (43.76)

.782 (19.86)

.926 (23.52)

1.043 (26.49)

1.183 (30.05)

1.305 (33.15)

1.391 (35.33)

1.531 (38.89)

1.656 (42.06)

1.777 (45.14)

1.230 (31.24)

1/2-20

5/8-24

3/4-20

7/8-20

1-20

1-1/16-18

1-3/16-18

1-5/16-18

1-7/16-18

POLARIZING

BOSS

U DIA.

E THD.

A

DIA.

W.130/.190

(3.30/4.83)

VC REF.

TYPE C TYPE S

TYPE R

Backshell Assemblies not supplied with MS connectors.

Performance Specifications - Page 158

Contacts, Sealing Pluts, Assembly Tools - Pages

163, 165

Contact Arrangments - Page 162

VS REF. VR REF.

GR

REF.

HR

FS

MS34745

Straight Plug, RFI Shielded

(Not supplied with MS Connectors)

Short

(C) Straight

(S) 90˚ Degree

(R)

Plug Assemblies with Backshell †

PV75

www.ittcannon.com 162

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

Contact Arrangements

Alternate Insert Positions

Face view, pin insert

Shell Size

No. of Contacts

Service Rating

8-33*

3-#20

I

14-12

4-#16, 8-#20

I

14-15

1-#16, 14-#20

I

14-18

18-#20

I

16-8

8-#16

II

16-23

1-#16, 22-#20

I

16-26

26-#20

I

18-8

8-#12

I

22-21

21-#16

II

20-41

41-#20

I

20-39

2-#16, 37-#20

I

20-16

16-#16

II

18-32

32-#20

I

18-11

11-#16

II

22-41

24-#20, 14-#16

I

SHELL

SIZE

Shell Contact Cavities

Contact

Arrangements

8

N

W˚

X˚

Y˚

Z˚

33

98

6

3

8

10

4

5

12

15

18

19

8

23

26

8

11

32

16

39

41

21

41

55

19

31

61

0˚

90˚

-

90˚

-

90˚

60˚

45˚

40˚

43˚

17˚

15˚

30˚

54˚

158˚

60˚

180˚

62˚

85˚

238˚

63˚

45˚

16˚

39˚

30˚

90˚

-

112˚

155˚

-

92˚

90˚

110˚

90˚

165˚

152˚

270˚

-

119˚

138˚

318˚

144˚

126˚

135˚

142˚

165˚

225˚

180˚

-

180˚

203˚

270˚

-

184˚

-

155˚

180˚

315˚

180˚

-

275˚

-

241˚

222˚

333˚

252˚

225˚

175˚

264˚

226˚

315˚

225˚

270˚

-

292˚

295˚

-

273˚

-

234˚

270˚

-

331˚

-

338˚

-

340˚

265˚

347˚

333˚

-

349˚

-

314˚

-

324˚

10

12

14

16

18

20

22

24

ARRANGE-

MENT

POS CODE

XN W Y Z

22-55

55-#20

I

24-19

19-#12

II

24-31

31-#16

I

24-61

61-#20

I

14-19

19-#20

I

8-98*

3-#20

I

10-6

6-#20

I

12-3

3-#16

II

12-8

8-#20

I

12-10

10-#20

I

14-4

4-#12

I

14-5

5-#16

II

Shell Size

No. of Contacts

Service Rating

Shell Size

No. of Contacts

Service Rating

Shell Size

No. of Contacts

Service Rating

Contact arrangements requiring reduced diameter

for lead-in chamfer on outer row of contact cavities

as indicated below.

* Layouts are available in shell styles MS3470 and MS3476 only.

8

12

14

16

18

22

33, 38

10

12

18

19

26

32

41

A, B, C

C, G

A, B, C, D, E, F, G, and H

A, C, E, G, J, and L

B, D, F, H, K, and M

A, B, C, D, E, F, G, H, J, K, L, M, N,

P, and R)

A, B, C, D, E, F,G, H, J, K, L, M, N,

P, R, S, and T

A, B, C, D, E, F, G, H, J, K, L, M, N,

P, R, S, T, U, V, W, X, and Y

AA

A

JK

B

BB

B

C

D

EE

E

F

G

H

A

AB

B

C

D

E

F

G

GH

H

J

JK

KL

LM

MN

N

P

R

T

U

V

W

WX

XY

Y

Z

ab

c

S

A

AB

B

C

D

E

F

G

H

J

K

L

M

N

P

R

T

U

V

VW

W

X

Y

Z

a

b

c

d

e

f

g

h

j

k

l

m

n

p

r

s

t

u

S

A

AB

BC

C

D

E

F

G

GH

H

J

K

L

M

N

P

R

T

U

V

W

X

Y

Z

a

b

c

d

e

f

g

h

j

k

l

m

n

p

s

t

S

A

AA

BB

B

CC

C

D

E

F

G

H

J

K

LL

L

M

N

P

R

T

U

V

WW

W

X

Y

Z

a

b

c

d

e

ff

f

gg

g

hh

h

jj

j

kk

l

mm

nn

r

p

s

t

u

v

w

x

z

AA

BB

CC

DD

EE

FF

GG

HH

S

A

AA

BB

CC

DD

EE

FF

GG HH

JJ

KK

LL

MM

NN

PP

A

B

BB

C

D

E

F

G

H

J

K

L

M

N

P

Q

P

R

T

U

V

W

X

Y

Z

a

b

c

d

e

f

g

h

j

k

i

m

n

r

z

y

x

w

v

u

p

q

s

t

S

A

B

BC

C

D

E

EF

F

G

GG

G

H

J

K

L

M

N

P

PR

R

T

TU

UV

S

B

C

B

C

D

E

F

BB

C

www.ittcannon.com 163

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

Thru-Bulkhead Receptacle

How to Order - PV-TBF

Tooling

PV-TBF

Shell

Size

8

10

12

14

16

18

20

22

24

.471 (11.96)

.588 (14.94)

.748 (19.00)

.873 (22.17)

.998 (25.35)

1.123 (28.52)

1.248 (31.70)

1.373 (34.87)

1.498 (38.05)

Notes: 1) Shell available in conductive (nickel finish) only. 2) Contacts are nonremovable.

PV-TBF - ITT Cannon prefix

Pin and socket

20

16

12

CIET-20-11

(274-7001-006) M81969/14-11

M81969/14-03

M81969/14-04

Red

Blue

Yellow

White

MS27534-20, MS3447-20, NAS1664-20

MS27534-16, MS3447-16, NAS1664-16

MS27534-12, MS3447-12, NAS1664-12

274-7007-000

274-7008-000

274-7009-00

CIET-16-03

(274-7002-000)

CIET-12-04

(274-7003-000)

Shell available in conductive (nickel fin-

ish) only.

Contacts are nonremovable.

Designed to MS3119 configuration and

meets the performance requirements of

MIL-C-26482 Series 2.

Notes: 1)

2)

3)

No designation required for normal. Standard MS

alternate posistions available.

8 through 24

10-6, 14-19, 16-8, 16-26, 18-32, 20-39, 20-

41, 22-41, 22-55, 24-61.

.062 (1.57)

.094 (2.39)

1.125 (28.58)

1.406 (35.71)

.577 (14.66)

.703 (17.86)

.594 (15.09)

.719 (18.26)

.812 (20.62)

.906 (23.01)

.969 (24.61)

1.062 (26.97)

1.156 (29.36)

1.250 (31.75)

1.375 (34.92)

.828 (21.03)

.954 (24.23)

1.047 (26.59)

1.141 (28.98)

1.234 (31.34)

1.328 (33.73)

1.453 (36.91)

1.578 (40.08)

1.703 (43.26)

.218 (5.54)

.344 (8.74)

.311 (7.90)

Contact

Size Cannon

Part Number M81969

Part Number Insertion

Color Tip Extraction

Color Tip Superseded

Mil. Pt. No.

Unwired Contact

Tools

Cannon Pt. No.

CBT 520/530

Insertion/Extraction Tools

Crimp Tool

M22520/1-01 Crimp Tool

with M22520/1-02 Turret

Wire Contact Tools

SERIES PREFIX

PV-TBF 10 -6 PS W

SERIES PREFIX

SHELL SIZE

INSERT ARRANGEMENTS

SHELL SIZE

INSERT ARRANGEMENTS

CONTACT STYLE

PANEL PANEL

XX

A

DIA.

K

A

DIA.

S

(TYP)

R

(TP)

POLARIZING

GROOVE

4 HOLES

.125/.115 (3.18/2.92) DIA.

SIZES 8-22

.152/.142 (3.86/3.61) DIA.

SIZES 24 ONLY

.140 RAD.

MAX.

M

L

FRONT

PANEL MOUNTING REAR

PANEL MOUNTING

ALTERNATE POLARIZING POSITION

A

Dia +_.003 (0.08) K

+_.016 (0.41) M

+_.016 (0.41)

L

Max. S

Max. X

Max.

R

(TP)

www.ittcannon.com 164

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

Panel Cutouts

Panel Thickness

Dummy Stowage Receptacles

Jam Nut Receptacle

Shell

Size

10

12

14

16

18

20

22

24

8

10

12

14

16

18

20

22

24

.474 (12.04)

.591 (15.01)

.751 (19.08)

.876 (22.25)

1.001 (25.43)

1.126 (28.60)

1.251 (31.78)

1.376 (34.95)

1.501 (38.13)

.594 (15.09)

.719 (18.26)

.812 (20.62)

.906 (23.01)

.969 (24.61)

1.062 (26.97)

1.156 (29.36)

1.250 (31.75)

1.375 (34.92)

.828 (21.03)

.954 (24.23)

1.047 (26.59)

1.141 (28.98)

1.234 (31.34)

1.328 (33.73)

1.453 (36.91)

1.578 (40.08)

1.703 (43.26)

.125 (3.18)

.125 (3.16)

.125 (3.18)

.152 (3.86)

.493 (12.52)

.587 (14.91)

.620 (15.75)

.078 (1.98)

.110 (2.79)

8

10

12

14

16

18

20

22

24

.661 (16.79)

.824 (20.93)

.948 (24.08)

1.072 (27.23)

1.197 (30.40)

1.322 (33.58)

1.447 (36.75)

1.572 (39.93)

Shown here are the maximum panel thickness

including screw head height allowable to ensure

complete connector operation. .125 (3.18) Max. (backshell

clearance for front mount)

.087 (2.21mm) maximum for

shell size 10 thru 18 (rear mount)

.212 (5.38mm maximum for

shell size 20 thru 24 (rear mount)

.125 (3.18) Max. (backshell

clearance for front mount)

.118 (3.00mm) maximum for

shell size 10 thru 18 (rear mount)

.212 (5.38mm maximum for

shell size 20 thru 24 (rear mount)

.697 (17.70)

.895 (22.73)

1.010 (25.65)

1.135 (28.33)

1.260 (32.00)

1.385 (35.18)

1.510 (38.35)

1.635 (41.53)

.620 (15.75)

.740 (18.80)

.864 (21.95)

.990 (25.15)

1.118 (28.40)

1.240 (31.50)

1.366 (34.70)

1.490 (37.85)

1.616 (41.05)

.594 (18.26)

.719 (18.26)

.812 (20.62)

.906 (23.01)

.969 (24.61)

1.062 (26.97)

1.156 (29.36)

1.250 (31.75)

1.375 (34.92)

.125 (3.14)

.125 (3.17)

.155 (3.97)

#4

#6

10

12

14

16

18

20

22

24

.740 (18.80)

.864 (21.95)

.990 (25.15)

1.118 (28.40)

1.240 (31.50)

1.366 (34.70)

1.490 (37.85)

1.616 (41.05)

.812 (20.62)

.938 (23.93)

1.031 (26.19)

1.125 (28.58)

1.203 (30.56)

1.297 (32.94)

1.375(34.92)

1.500 (38.10)

.155 (3.97)

#6

F DIA.

G DIA.

4 HOLES

A

DIA

J K

E

(TP)

MS - Complies with MIL-C-26482PVS - ITT Cannon prefix

- 15 -PV

G - Conductive finish (nickel)

A - Nonconductive finish (anodized)

8 though 24

3115 - Dummy receptacle

8 through 24

L - Conductive finish (nickel)

A - Nonconductive finish (anodized)

NOTE: Usable on KPT/KPSE series also.

F

(TYP)

E

+_.005 (+_.13) +.010 (0.25)

-.000 (0.00)

DIA.

A

T DIA. 4 MTG. HOLES

R

(TYP.)

Shell

Size A

Dia. Max. E

(TYP) F

Max. G

Max. J

Max. K

Max.

Shell

Size

Narrow Flange Receptacle Wide Flange Receptacle

BACKSHELL BACKSHELL

COUPLING NUT

How to Order

PV DESCRIPTION MS DESCRIPTION

SERIES PREFIX SERIES PREFIX

MS STANDARD

SHELL SIZE

CLASS

PVS -15 G 12 MS 3115 -12 L

DUMMY RECEPTACLE INDICATOR

CLASS

SHELL SIZE

COUPLING NUT

A

Dia. T

Dia. Screw

SizeR Shell

Size A

Dia. T

Dia. Screw

SizeR

E

+_.005 (0.13) F Dia.

+_.005 (0.13) Flange Front

and Rear

Mounting Mounting

Hole

Flange Front

and Rear

Mounting Mounting

Hole

Narrow Flange and Thru-Bulkhead/Wide Flange

www.ittcannon.com 165

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

Protective Metal Caps

Contacts

Wire Hole Fillers

Plugs

SERIES PREFIX

PVS - ITT Cannon Prefix

MS - Complies with MIL-C-26482 (Series 2)

80 or 3180 - Plug Cap

81 or 3181 - Receptacle Cap

8 thru 24

C - Sash chain (MS approved)

N - Sash chain with ring (81 or3181 type only) MS approved

A - Hard anodic, non-conductive (MS approved)

G - Nickel, conductive (not MS) (PVS only)

NOTE: Usable on KPT/KPSE series also.

FA

L

M

BQ

R

N

.047

1,19mm)

Max.

.094

2,39mm)

Max.

.169 +_ .008 DIA.

(4.29 +_ 0.20)

H +.500 (12.7)

-.250 (6.35)

H +.500 (12.7)

-.250 (6.35) N style used primarily on Jam Nut Receptacle.

TYPE

SHELL SIZE

TERMINATION STYLE

FINISH

CHAIN LENGTH

PVS

MS

Shell

Size

8

10

12

14

16

18

20

22

24

Contact

Size M39029

Number

Contact

Size Alumel

Thermocouple Contacts

Contacts for printed circuit applications are also

available. Consult factory.

Chromal

Type 1st

Color Brands

2nd 3rd ITT Cannon

20

16

12

Contact

Size Cannon Military Superseded

Mil. Pt. No. Color

Code

Part Number

20

16

12

225-0070-000

225-0071-000

225-0072-000

MS27488-20

MS27488-16

MS27488-12

Red

Blue

Yellow

MS3187-20

M83723/28-20

MS3187-16

M83723/28-16

MS3187-12

M83723/28-12

Socket

M39029/5-115

M39029/4-110

M39029/5-116

M39029/4-111

M39029/5-118

M39029/4-113

Brown

Green

Black

Blue

Brown

Grey

Orange

031-9174-004

030-9173-006

031-9206-006

030-9205-007

031-9186-003

030-9185-003

20 Pin

20 Socket

030-1831-000

031-1013-000

030-1832-000

031-1014-000

.474 (12.04)

.591 (15.01)

.751 (19.08)

.876 (22.25)

1.001 (25.43)

1.126 (28.60)

1.251 (31.78)

1.376 (34.96)

1.501 (38.13)

.486 (12.34)

.607 (15.42)

.766 (19.46)

.890 (22.60)

1.015 (25.78)

1.141 (28.98)

1.265 (32.13)

1.390 (35.31)

1.515 (38.48)

.719 (18.26)

.844 (21.44)

1.000 (25.40)

1.125 (28.58)

1.250 (31.75)

1.375 (34.93)

1.500 (38.10)

1.625 (41.26)

1.750 (44.45)

3.000 (76.20)

3.500 (76.20)

3.500 (88.90)

4.000 (101.60)

.562 (14.27)

.625 (15.88)

.658 (16.71)

.399 (10.13)

.461 (11.71)

.461(11.71)

.494 (12.55)

.578 (14.68)

.703 (17.86)

.891 (22.63

1.016 (25.81)

1.141 (28.98)

1.266 (32.16)

1.391 (35.33)

1.516 (38.51)

1.641 (41.68)

.734 (18.64)

.859 (21.82)

1.000 (25.40)

1.125 (28.58)

1.250 (31.75)

1.375 (34.93)

1.500 (38.10)

1.625 (41.26)

1.750 (44.45)

.562 (14.27)

.602 (15.29)

A

Max. Dia. B

Max. F

Max. Dia. L

Max. M

Max. N

Min. Dia. Q

Max. R

Max.H

80

3180

-12

C

A

CHAIN LENGTH

Receptacles

www.ittcannon.com 166

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-26482, Series 2 Connectors PV

Assembly Procedures

STRIPPING AND CRIMPING

3/16" for

#20 CONTACT 9/32" for

#16 CONTACT 9/32" for

#12 CONTACT Right

Wrong

CONTACT INSERTION

OPENING

COLORED END

FOR INSERTION

CONTACT EXTRACTION

COMPLETION

BROKEN CIRCLE

BREAK

1. Strip wires according to contact size: 3/16" for #20 and 9/32"for

#16 and#12. #20 contacts accommodate AWG wire sizes 20, 22, or

24; #16 accommodates 16, 18 or 20; and #12 accommodates 12 or 14.

4. Insert contact and wire into tool jaws. To crimp, squeeze handles

together fully until ratchet release and allows handles to expand;

otherwise, contact cannot be extracted from tool jaws. Maintain slight

insertion pressure on wire while crimping contact to wire.

3. Slide back tool on wire shile holding thumb against wire at opening.

Wire will slip into tool.

NOTE: Socket contacts should be inserted partially into grommet

by hand before using insertion tool.

6. Withdraw tool from rear of plug. To be sure that contact is locked,

pull back lightly on wire. Then remove tool from wire and proceed with

other contacts.

2. Push tool into rear of plug until it bottoms. At this point, tool

releases tines on retaining clip so that contact can be extracted. 3. While maintaining slight insertion force on tool, firmly hold wire

against serrated shoulder at center of tool and extract both wired

contact and tool from plug.

4. Check face of plug or receptacle for proper contact installation. In

socket inserts with a large number of contact, cavities are identified in

a spiral pattern. A projecting line from the spiral indictates omission of a

letter; a broken circle around a cavity indicates transition between

capitals and lower case and double letters.

7. After all contacts are inserted, fill unwired cavities with sealing

plugs (insert head last and leave end protruding for ease of removal),

assemble backshell on rear of connector .

1. Remove backshell and slide back along wires to allow access. To

extract a contact, use white end of CIET tool. Place wire into tool at

large opening. Slide back tool on wire while holding thumb against wire

at opening. Wire will slip into tool.

4. With tool pressed against shoulder of contact, starting at the center

cavity, insert wired contact and tool into properly identified cavity at

rear of plug with firm, even pressure. Do not use excessive pressure.

5. When contact bottoms, a slight click can be heard as tines of metal

reataining clip snaps into place behind contact shoulder .

1. Remove backshell and put wired contacts thru cable clamp opening. 2. Used colored end of CIET tool for insertion. Place wire into tool at

large opening. To facilitate contact insertion, a 6-in. min. free lenght of

wire is recommended.

2. Insert wire into rear of contact. Wire insulation must butt against

rear of contact. Wire must be visible thru inspection hole. 3. Use M22520/1-01 crimp tool with proper crimp locator M22520/

1-02. The color code hand on the contact (red for #20, blue for #16

and yellow for #12) must match the color code of the locator and the

insertion tool throughout the crimping and assembly operations.