(Notice)
•In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment
using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before
using any SHARP device.
•Specifications are subject to change without notice for improvement.
(Internet)
•Data for Sharp's optoelectronic/power devices is provided on internet. (Address http://sharp-world.com/ecg/)
D5-020902
Outline Dimensions
Under development
New product
Low Power-Loss Voltage Regulator
Low Output Current, Compact Surface Mount Type Low Power-Loss Voltage Regulators
(1)
Compact package : TO-92 type
(Size(mold part) 5.2 × 5.5 × 4.2 mm)
(2) Small current output : 100 mA(MAX.)
(3) Low consumption current :
Quiescent current Iq=MAX. 350 µA
(4) Low power-loss :
Dropout voltage : MAX. 0.26 V at Io=60 mA
Dropout voltage : MAX. 0.4 V at Io=150 mA
(5)
Built-in overcurrent, overheat protection functions
(6) Taped package
(1) TV
(2) VCR
(3) Air conditioner
(4) DVD player
(5) Audio equipment
(Unit: mm)
(Ta=25°C)
*1 All are open except GND
and applicable terminals.
*2 At mounted condition
*3 Overheat protection may operate
at 125Tj150°C.
Input voltage
Output current
Power dissipation
Junction temperature
Operating temperature
Storage temperature
Soldering temperature
*1
*2
*3
Vin
Io
Pd
Tj
Topr
Tstg
Tsol
16
150
520
150
-30 to +80
-55 to +150
260(For 10s)
V
mA
mW
°C
°C
°C
°C
1/2
Features
Applications
Absolute Maximum Ratings
Parameter Symbol Ratings Unit
PQ033ES1MXP
PQ050ES1MXP
1
2
3
123
1
2
3
0.1
0.4
2.5±
0.1
0.4
2.5±
0.6(MAX)
12.7(MIN)
10.0(MIN)
3.0±0.7 2.3(MAX)
5.5(MAX)
5.2(MAX)
0.45±0.1 0.4±0.05
1.4±0.1
4.2(MAX)
R2.4
Internal connection
Control
circuit
DC input(Vin)
DC output(Vo)
GND
*4 Dropout voltage when output voltage lowers 0.1V from the voltage at Vin=Vo+1V.
As of September 2002
(Unless otherwise specified, Vin=Vo(TYP.)+1.0V, Io=30mA.Ta=25°C)
D5-020902
2/2
Low Power-Loss Voltage Regulator
Electrical Characteristics
Unit
V
mV
mV
mV
mV
mV/°C
dB
V
V
µA
Parameter
Output voltage
Load regulation
Line regulation
Temperature coefficient of output voltage
Ripple rejection
Dropout voltage
Quiescent current
Symbol
Vo
RegL1
RegL2
RegL3
RegI
TcVo
RR
Vi-o1
Vi-o2
Iq
MAX.
50
100
160
20
-
-
0.26
0.4
350
TYP.
10
20
30
3.0
0.05
55
0.11
0.2
170
MIN.
-
-
-
-
-
-
-
-
-
Conditions
-
Io=5mA to 60mA
Io=5mA to 100mA
Io=5mA to 150mA
Vin=
Vo(TYP.)+1V to
Vo(TYP.)+6V
Io=10mA, Tj=-25 to +75°C
-
Io=60mA, Vin=*4
Io=150mA, Vin=*4
Io=0mA
Refer to the table below.
Output voltage VOV
3.234
4.900 3.3
5.0 3.366
5.100
(Vin=Vo(TYP.)+1.0V, Io=30mA.Ta=25°C)
PQ033ES1MXP
PQ050ES1MXP
Output Voltage Line-up
Parameter Symbol Conditions MIN. TYP. MAX. Unit
PQ033ES1MXP
PQ050ES1MXP
NOTICE
The circuit application examples in this publication are provided to explain representative applications of SHARP
devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes
no responsibility for any problems related to any intellectual property right of a third party resulting from the use of
SHARP's devices.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP
reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents
described herein at any time without notice in order to improve design or reliability. Manufacturing locations are
also subject to change without notice.
Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage
caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used
specified in the relevant specification sheet nor meet the following conditions:
(i) The devices in this publication are designed for use in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when
SHARP devices are used for or in connection with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of
reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g., scuba).
If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign
Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices.
This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright
laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written
permission is also required before any use of this publication may be made by a third party.
Contact and consult with a SHARP representative if there are any questions about the contents of this publication.