VS-25TTS..FPPbF Series, VS-25TTS..FP-M3 Series www.vishay.com Vishay Semiconductors Thyristor High Voltage, Phase Control SCR, 25 A FEATURES * Designed and qualified for industrial level 2 (A) * Fully isolated package (VINS = 2500 VRMS) * UL E78996 pending * 125 C max. operating junction temperature 1 2 * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 3 1 (K) (G) 3 TO-220AB FULL-PAK Available APPLICATIONS * Typical usage is in input rectification crowbar (soft start) and AC switch in motor control, UPS, welding, and battery charge PRODUCT SUMMARY Package TO-220AB FP Diode variation Single SCR IT(AV) 16 A VDRM/VRRM 800 V, 1200 V VTM 1.25 V DESCRIPTION IGT 45 mA TJ - 40 C to 125 C The VS-25TTS...FP... high voltage series of silicon controlled rectifiers are specifically designed for medium power switching and phase control applications. The glass passivation technology used has reliable operation up to 125 C junction temperature. OUTPUT CURRENT IN TYPICAL APPLICATIONS APPLICATIONS SINGLE-PHASE BRIDGE THREE-PHASE BRIDGE UNITS 18 22 A Capacitive input filter TA = 55 C, TJ = 125 C, common heatsink of 1 C/W MAJOR RATINGS AND CHARACTERISTICS PARAMETER IT(AV) TEST CONDITIONS VALUES IRMS A 25 VRRM/VDRM ITSM VT UNITS 16 Sinusoidal waveform 16 A, TJ = 25 C dV/dt dI/dt TJ 800/1200 V 350 A 1.25 V 500 V/s 150 A/s - 40 to 125 C VOLTAGE RATINGS PART NUMBER VRRM, MAXIMUM PEAK REVERSE VOLTAGE V VDRM, MAXIMUM PEAK DIRECT VOLTAGE V VS-25TTS08FPPbF, VS-25TTS08FP-M3 800 800 VS-25TTS12FPPbF, VS-25TTS12FP-M3 1200 1200 Revision: 26-Jul-13 IRRM/IDRM AT 125 C mA 10 Document Number: 94384 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-25TTS..FPPbF Series, VS-25TTS..FP-M3 Series www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Maximum average on-state current IT(AV) Maximum RMS on-state current IRMS Maximum peak, one-cycle, non-repetitive surge current ITSM TC = 51 C, 180 conduction half sine wave 16 10 ms sine pulse, rated VRRM applied 300 10 ms sine pulse, no voltage reapplied 350 25 UNITS A 450 630 I2t t = 0.1ms to 10 ms, no voltage reapplied 6300 A2s VTM 16 A, TJ = 25 C 1.25 V 12.0 m 1.0 V Maximum I2t for fusing Maximum on-state voltage drop Maximum reverse and direct leakage current TYP. MAX. 10 ms sine pulse, rated VRRM applied I2t Threshold voltage VALUES 10 ms sine pulse, no voltage reapplied Maximum I2t for fusing On-state slope resistance TEST CONDITIONS rt VT(TO) IRM/IDM TJ = 125 C TJ = 25 C TJ = 125 C A2s 0.5 VR = Rated VRRM/VDRM 10 mA Holding current IH Anode supply = 6 V, resistive load, initial IT = 1 A, TJ = 25 C Maximum latching current IL Anode supply = 6 V, resistive load, TJ = 25 C 200 TJ = TJ max., linear to 80 %, VDRM = Rg - k = Open 500 V/s 150 A/s VALUES UNITS Maximum rate of rise of off-state voltage dV/dt Maximum rate of rise of turned-on current dI/dt 150 - TRIGGERING PARAMETER TEST CONDITIONS SYMBOL PGM 8.0 Maximum average gate power PG(AV) 2.0 Maximum peak positive gate current + IGM 1.5 A Maximum peak negative gate voltage - VGM 10 V Maximum peak gate power Maximum required DC gate current to trigger Maximum required DC gate voltage to trigger IGT VGT Maximum DC gate voltage not to trigger VGD Maximum DC gate current not to trigger IGD Anode supply = 6 V, resistive load, TJ = - 10 C 60 Anode supply = 6 V, resistive load, TJ = 25 C 45 Anode supply = 6 V, resistive load, TJ = 125 C 20 Anode supply = 6 V, resistive load, TJ = - 10 C 2.5 Anode supply = 6 V, resistive load, TJ = 25 C 2.0 Anode supply = 6 V, resistive load, TJ = 125 C 1.0 TJ = 125 C, VDRM = Rated value W mA V 0.25 2.0 mA VALUES UNITS SWITCHING PARAMETER SYMBOL Typical turn-on time tgt Typical reverse recovery time trr Typical turn-off time tq Revision: 26-Jul-13 TEST CONDITIONS TJ = 25 C TJ = 125 C 0.9 4 s 110 Document Number: 94384 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-25TTS..FPPbF Series, VS-25TTS..FP-M3 Series www.vishay.com Vishay Semiconductors THERMAL AND MECHANICAL SPECIFICATIONS PARAMETER SYMBOL Maximum junction and storage temperature range TJ, TStg Maximum thermal resistance, junction to case RthJC Maximum thermal resistance, junction to ambient RthJA Typical thermal resistance, case to heatsink RthCS TEST CONDITIONS VALUES UNITS - 40 to 125 C DC operation 2.5 Mounting surface, smooth and greased 0.5 2 Approximate weight Mounting torque 0.07 oz. 6 (5) maximum 12 (10) kgf * cm (lbf * in) Maximum Average On-sta te Power Loss (W) Maximum Allowable Case Temperature (C) 140 25TTS.. Series 120 100 80 60 30 90 120 20 180 0 0 5 10 15 180 120 90 60 30 20 15 RMSLimit 10 Conduction Angle 25TTS.. Series TJ= 125C 5 0 0 20 4 Maximum Averag e On-state Power Loss (W) Maximum Allowable Case Temperature (C) 25TTS.. Series 120 100 80 60 60 90 120 180 DC 0 0 5 10 15 20 25 Average On-state Current (A) Fig. 2 - Current Rating Characteristics Revision: 26-Jul-13 12 16 20 Fig. 3 - On-State Power Loss Characteristics 140 20 8 Avera ge On-state Current (A) Fig. 1 - Current Rating Characteristics 30 25TTS12FP 25 Average On-state Current (A) 40 25TTS08FP Case style TO-220AB FULL-PAK (94/V0) 60 g minimum Marking device 40 C/W 62 30 35 DC 180 120 90 60 30 30 25 20 RMSLimit 15 Conduc tion Period 10 25TTS.. Series T J = 125C 5 0 0 5 10 15 20 25 30 Avera ge On-sta te Current (A) Fig. 4 - On-State Power Loss Characteristics Document Number: 94384 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-25TTS..FPPbF Series, VS-25TTS..FP-M3 Series 350 Vishay Semiconductors 400 At Any Rated Load Cond ition And With Rated V RRM App lied Following Surge. Initial TJ = 125C @60 Hz 0.0083 s @50 Hz 0.0100 s 300 Peak Half Sine Wa ve On-state Current (A) Peak Half Sine Wave On-state Current (A) www.vishay.com 250 200 25TTS.. Series 150 1 10 350 300 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduc tion Ma y Not Be Mainta ined. Initia l TJ = 125C No Voltage Rea pp lied Rated VRRM Reapp lied 250 200 150 25TTS.. Series 100 0.01 100 0.1 1 Pulse Train Duration (s) Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 5 - Maximum Non-Repetitive Surge Current Fig. 6 - Maximum Non-Repetitive Surge Current Insta ntaneous On-state Current (A) 1000 100 TJ= 25C TJ= 125C 10 25TTS.. Series 1 0 1 2 3 4 5 Instanta neous On-state Voltage (V) Fig. 7 - On-State Voltage Drop Characteristics Thermal Impedance ZthJC (C/W) 10 D = 0.5 D = 0.2 1 D = 0.1 D = 0.05 D = 0.02 D = 0.01 0.1 0.01 1E-05 Single Pulse (Thermal Resistance) 1E-04 1E-03 1E-02 1E-01 1E+00 1E+01 1E+02 Square Wave Pulse Duration (s) Fig. 8 - Thermal Impedance ZthJC Characteristics Revision: 26-Jul-13 Document Number: 94384 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-25TTS..FPPbF Series, VS-25TTS..FP-M3 Series www.vishay.com Vishay Semiconductors Rectangular gate pulse a)Recommended load line for rated di/ dt: 10 V, 20 ohms tr = 0.5 s, tp >= 6 s b)Rec ommended load line for <= 30% rated d i/ dt: 10 V, 65 ohms 10 tr = 1 s, tp >= 6 s (1) PGM = 40 W, tp = 1 ms (2) PGM = 20 W, tp = 2 ms (3) PGM = 8 W, tp = 5 ms (4) PGM = 4 W, tp = 10 ms (a) (b) VGD TJ = -10 C TJ = 125 C 1 TJ = 25 C Instantaneous Gate Voltage (V) 100 IGD (4) 25TTS.. Series 0.1 0.001 0.01 (3) (2) (1) Frequenc y Limited by PG(AV) 0.1 1 10 100 Instantaneous Gate Current (A) Fig. 9 - Gate Characteristics ORDERING INFORMATION TABLE Device code VS- 25 T T S 12 FP PbF 1 2 3 4 5 6 7 8 1 - Vishay Semiconductors product 2 - Current rating (25 = 25 A) 3 - Circuit configuration: T = Single thyristor 4 - Package: T = TO-220AB 5 - Type of silicon: 6 - Voltage code x 100 = VRRM 7 - FULL-PAK 8 - Environmental digit: Standard recovery rectifier 08 = 800 V 12 = 1200 V PbF = Lead (Pb)-free and RoHS compliant -M3 = Halogen-free, RoHS compliant, and terminations lead (Pb)-free ORDERING INFORMATION (Example) PREFERRED P/N QUANTITY PER T/R MINIMUM ORDER QUANTITY PACKAGING DESCRIPTION VS-25TTS08FPPbF 50 1000 Antistatic plastic tubes VS-25TTS08FP-M3 50 1000 Antistatic plastic tubes VS-25TTS12FPPbF 50 1000 Antistatic plastic tubes VS-25TTS12FP-M3 50 1000 Antistatic plastic tubes LINKS TO RELATED DOCUMENTS Dimensions Part marking information Revision: 26-Jul-13 www.vishay.com/doc?95072 TO-220FP PbF www.vishay.com/doc?95069 TO-220FP -M3 www.vishay.com/doc?95456 Document Number: 94384 5 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Outline Dimensions www.vishay.com Vishay Semiconductors DIMENSIONS in millimeters 10.6 10.4 Hole O 3.4 3.1 2.8 2.6 3.7 3.2 7.31 6.91 16.0 15.8 16.4 15.4 10 3.3 3.1 13.56 13.05 2.54 TYP. 0.61 0.38 0.9 0.7 2.54 TYP. R 0.7 (2 places) R 0.5 1.4 1.3 2.85 2.65 1.15 TYP. 1.05 Lead assignments 4.8 4.6 Diodes 1. - Anode/open 2. - Cathode 3. - Anode 5 0.5 Revision: 20-Jul-11 5 0.5 Conforms to JEDEC outline TO-220 FULL-PAK Document Number: 95072 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Vishay: VS-25TTS08FPPBF VS-25TTS12FPPBF VS-25TTS12FP-M3