139 FIBER SENSORS Digital Fiber Sensor FX-300 SERIES Related Information LASER SENSORS General terms and conditions.............. F-7 SC-GU1-485............................... P.1009~ General precautions.................... P.1458~ Sensor selection guide..................... P.3~ Glossary of terms........................ P.1455~ Korea's S-mark.............................. P.1506 PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Conforming to EMC Directive Recognition AREA SENSORS Certified LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS NPN output types of connector type only * Passed the UL 991 Environment Test * UL 61010C-1 compatible, Passed the UL 991 Environment Test based on SEMI S2-0200. [Category applicable for semiconductor manufacturing: TWW2, Process Equipment] [Applicable standards: UL 61010C-1] [Additional test / evaluation standards as per intended use: UL 991, SEMI S2-0200] PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS PNP output type available WIRE-SAVING SYSTEMS panasonic.net/id/pidsx/global MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Timer Interference Light intensity monitor prevention Automatic sensitivity setting Constant advances achieving significant improvement of sensing performance Stable sensing over long and short periods FX-301 FX-301-HS FX-305 In addition to a "four-chemical emitting element" which suppresses changes in the light emitting element over time so that a stable level of light emission can be * * maintained over long periods, a "APC (Auto Power * Control) circuit" has also been adopted afresh. The light emitting amount can be controlled in minute degrees so that even changes occurring over very short periods can be handled, allowing stable sensing performance by suppressing deviations in light emitting amounts caused by changes in the ambient environment that could not previously be suppressed. Even greater sensing range All models Adoption of a "double coupling lens" that increases emission efficiency to its maximum limits and greatly increases sensing range. Sensing ranges with small diameter fibers and ultra-small diameter fibers, which have become very popular due to the miniaturization of chip components, have been increased by 50 % over previous values achieved with other amplifiers. * Conventional fiber sensors (Without lens) Stable sensing comparison Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F Light emitting amount Fibers Short-term stability Disperses the light reduces emitting efficiency. Deviation * Double coupling lens Long-term stability Time FX-301 FX-301-HS FX-305 Three-chemical emitting element, Without APC The lens concentrates the light, greatly increasing emitting efficiency. Digital Fiber Sensor FX-300 SERIES APPLICATIONS 140 FIBER SENSORS Detecting the presence or absence of labels Detecting the presence or absence of ICs on a tray The light-emitting amount selection function can even stabilize detection of transparent labels that saturate the light-receiving level. You can set upper and lower limits for the threshold values using the window comparator mode and turn ON / OFF the incident light intensity within that limit. Detecting the passage of small objects The differential sensing mode will only detect rapid changes in the amount of light, which makes it possible for small objects to be detected. LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS FX-301 FX-301-HS FX-305 Light-emitting amount selection If the light receiving level becomes saturated during close-range sensing or when sensing transparent or minute objects, you can adjust the light emitting amount of the sensor to stabilize sensing without needing to change the response time. Sensing that previously required the response time or fibers to be changed can now be set much more easily using this function. [Light receiving level saturated] A 4000 Actual digit difference: C Upper display limit B Saturated digit difference: D Light emitting amount changed , A , B SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS Level 4 Level 3 WIRE-SAVING SYSTEMS Level 2 MEASUREMENT SENSORS Level 1 STATIC ELECTRICITY PREVENTION DEVICES [Stable sensing] Actual digit difference: C' PARTICULAR USE SENSORS LASER MARKERS OFF Light emitting amount can be changed without changing response time PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS FX-305 Large display 9999 Large display with 4 digits (9999). With a greater difference in digit value than previous models, threshold values can be set in units of 1 digit up to maximum 9999. Threshold setting can now be done more easily and accurately. (During STDF, LONG and U-LG modes) 2.5 times previous models Digit difference comparison Example Digit difference between object A and object B Previous models FX-305 4000 9999 Ultra high-speed 35 s response FX-301-HS FX-305 Ultra high-speed 35 s response. Even small objects moving at high speeds can be sensed. In addition, at 65 s the FX-301 standard 4 times as fast type and FX-305 highas before function type is also twice as fast as previous models. 35 s Selection Guide Fiber Amplifiers Ultra high-speed type FX-301-HS (H-SP mode) 35 s Standard type FX-301, High-function type FX-305 65 s Digit difference: Large UV CURING SYSTEMS Fibers (H-SP mode) Digit difference: Small MACHINE VISION SYSTEMS Previous model 150 s FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS Digital Fiber Sensor FX-300 SERIES A window comparator mode and differential sensing mode have been added. These modes make it easy to carry out sensing tasks that previously required multiple sensors or involved complex threshold settings. Window comparator mode Differential sensing mode <Sensing ICs in trays> <Sensing of tiny moving objects> LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Tray absent IC present Tray present OFF ON OFF SENSOR OPTIONS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS Incident light intensity Upper and lower limits for threshold values can be set so that the incident light intensity can turn on and off within those ranges. Single output is used, so that only one cable is required, and no PLC processing is required either. SIMPLE WIRE-SAVING UNITS STATIC ELECTRICITY PREVENTION DEVICES FX-305 Simplified systems using new operating modes Lower light amounts due to dust Incident light intensity 141 Because sensing is not possible at normal sensitivity settings, sensitivity must be reset. ON ON Sensing of only sudden changes in light amounts Only the target objects are sensed. No need to reset the sensitivity. FX-305 Equipped with 5 types timers The FX-305 includes the same ON-delay / OFF-delay / ONE SHOT timer as the FX-301(-HS), as well as an ON-delay * OFF-delay timer and an ON-delay * ONE SHOT timer. A wide variety of timer control operations can be carried out by these fiber sensors alone. Timer period Output 1: 0.5 to 9,999 ms (variable) Output 2: 0.5 to 500 ms (variable) Time chart ONE SHOT UV CURING SYSTEMS ON-delay * OFF-delay ON-delay * ONE SHOT Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F RUN TEACH ADJ RUN RUN TEACH ADJ TEACH RUN TEACH ADJ ADJ OFF T1 T1 ON OFF T1 ON T1 OFF T1 T1 T2 T2 ON OFF ON OFF All models Even beginners can quickly learn how to use the MODE NAVI MODE NAVI uses six indicators to display the amplifier's basic operations. The current operating mode can be confirmed at a glance, so even a first time user can easily operate the amplifier without becoming confused. ON T1 OFF-delay MACHINE VISION SYSTEMS Fibers Beamreceived Beaminterrupted Sensing condition ON-delay FA COMPONENTS Selection Guide For L-ON L / D L / D ON TIMER This mode allows the selection of output operation as either PRO Light-ON or Dark-ON. This is the sensing mode. Incident light level is displayed in the digital display. L / D TIMER TIMER This mode permits the choice of using or not PRO using the timer. This mode is for setting the threshold value. L / D PRO TIMER This mode allows the selection of further advanced functions, such as the copying of PRO individual settings and the memory functions. In this mode, the threshold value, once set, may be fine-tuned. FX-301 FX-301-HS FX-305 Easy confirming of threshold value settings The threshold value can be confirmed by turning the jog switch even during RUN mode. Jog switch is turned Left: FX-301(-HS) Right: Output 2 for Output 1 for FX-305 FX-305 The threshold value is displayed Digital Fiber Sensor FX-300 SERIES All models The use of only two switches makes for very simple operations Only two switches, the large jog switch and the large MODE key, are required for operation. You can operate it simply by the 3 steps shown on the right. Large MODE key Large jog switch 1 142 FIBER SENSORS LASER SENSORS 2 3 PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS Pressing the switch selects or cancels the operating mode Moving the switch from side to side allows items to be selected Pressing the switch then confirms the selected setting A quick-connection cable saves wiring and Connector type work-hours An optical communication function allows up to *16 sensors FX-301 FX-305 to be adjusted simultaneously One unit can be used as either a main unit or sub unit The optical communication function allows the data that is currently set to be copied and saved all at once for all amplifiers connected together from the right side. This greatly reduces troublesome setup tasks and makes setup much smoother. In addition, troublesome adjustment operations at times such as when replacing sensors can also be carried out easily and data can also be Single copy & save operation for all amplifiers copied and stored using the optical communication function. The amplifier unit can be used as either a main unit or a sub unit. This feature allows for easy mounting in the side-by-side configuration. The main and sub unit functions are distinguished only by the proper use of the main cable and the sub cable. Moreover, inventory management and maintenance is simplified. Identical part numbers eliminate the need for costly inventory management labor * Use the optical communication function for only the same types of sensors. Furthermore, the FX-301-HS is not equipped with optical communication function capability. Settings can be entered directly using numerical input All models Sub cable FX-305 FX-301(-HS) FX-301B/G/H Main cable (4-core) CN-74-C Every function can be directly set merely by the input of a four digit code (numbers) from the code table. This convenient feature is easy to set up. In the event that settings are accidentally changed at the operating site, merely entering the correct code can restore the original settings. This results in easy and quick maintenance. First digit: Settings for response time and hysteresis Sub cable (2-core) CN-72-C Second digit: Settings for L/D ON and display mode LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Main cable (3-core) Main cable CN-73-C Sub cable (1-core) CN-71-C Fourth digit: Timer period settings Third digit: Settings for Adjust lock and timer Communication unit improves equipment starting up and maintenance External input unit for digital sensor FX-CH2 Teaching and changing settings can be performed by using the PLC and touch panel. FX-301 FX-305 Upper communication unit for digital sensor SC-GU1-485 We now offer remote maintenance for digital sensors! Various settings and switching of up to 16 units of digital fiber sensors can be accomplished at once without operating the actual sensors themselves, but via external signals, such as the PLC, touch panel, and push buttons. The communication unit enables inputs to the digital fiber sensors (such as teaching and data bank switching) to be carried out via a PLC or a personal computer, and also allows confirming of the incident light intensity an output status for the fiber sensors. This greatly improves workability during equipment starting up and maintenance. <Main functions> * Batch teaching * Key lock setting * Batch loading / saving of the data bank <Communicable commands> * Sensor incident light intensity * Sensor settings verification * Sensor output status * Threshold value settings, etc. FX-301(P) FX-305(P) PLC Refer to our website for details Compatible with all PLCs equipped with RS-485 compatible units SC-GU1-485 RS-485 communication Refer to SC-GU1-485 pages for details Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F 143 Amplifiers Quick-connection cable is not supplied with the amplifier. Please order it separately. Type MICRO PHOTOELECTRIC SENSORS Appearance Model No. FX-301 AREA SENSORS FX-301B SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS High-speed type LASER MARKERS Model No. Length CN-73-C1 1 m 3.281 ft CN-73-C2 2 m 6.562 ft CN-73-C5 5 m 16.404 ft CN-71-C1 1 m 3.281 ft CN-71-C2 2 m 6.562 ft CN-71-C5 5 m 16.404 ft CN-74-C1 1 m 3.281 ft CN-74-C2 2 m 6.562 ft CN-74-C5 5 m 16.404 ft CN-72-C1 1 m 3.281 ft CN-72-C2 2 m 6.562 ft CN-72-C5 5 m 16.404 ft NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor Blue LED FX-301BP PNP open-collector transistor FX-301G NPN open-collector transistor Green LED FX-301GP PNP open-collector transistor FX-301H NPN open-collector transistor Infrared LED MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES Quick-connection cables Type Main cable (3-core) PRESSURE / FLOW SENSORS Standard type FX-301P PARTICULAR USE SENSORS Output Red LED LIGHT CURTAINS / SAFETY COMPONENTS INDUCTIVE PROXIMITY SENSORS Emitting element FX-301HP PNP open-collector transistor FX-301-HS NPN open-collector transistor Sub cable (1-core) PHOTOELECTRIC SENSORS ORDER GUIDE Main cable (4-core) LASER SENSORS FX-300 SERIES Sub cable (2-core) FIBER SENSORS Digital Fiber Sensor Red LED FX-301P-HS PNP open-collector transistor PLC HUMAN MACHINE INTERFACES FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F FX-305 High-function type ENERGY CONSUMPTION VISUALIZATION COMPONENTS NPN open-collector transistor Red LED FX-305P PNP open-collector transistor Digital Fiber Sensor FX-300 SERIES ORDER GUIDE 144 FIBER SENSORS Quick-connection cables LASER SENSORS For FX-301(-HS)/B/G/H Quick-connection cable is not supplied with the amplifier. Please order it separately. Main cable PHOTOELECTRIC SENSORS Type Main cable (3-core) Sub cable (1-core) Model No. CN-73-C1 Description Length: 1 m 3.281 ft CN-73-C5 0.2 mm2 3-core cabtyre cable, with connector Length: 2 m 6.562 ft on one end Cable outer diameter: o3.3 mm o0.130 in Length: 5 m 16.404 ft CN-71-C1 Length: 1 m 3.281 ft CN-73-C2 CN-71-C2 CN-71-C5 MICRO PHOTOELECTRIC SENSORS * CN-73-C 0.2 mm2 1-core cabtyre cable, with connector Length: 2 m 6.562 ft on one end Cable outer diameter: o3.3 mm o0.130 in Length: 5 m 16.404 ft AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS Sub cable INDUCTIVE PROXIMITY SENSORS * CN-71-C PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS For FX-305 Quick-connection cable is not supplied with the amplifier. Please order it separately. Type Main cable (4-core) Sub cable (2-core) Model No. CN-74-C1 Description CN-74-C5 CN-72-C1 Length: 1 m 3.281 ft CN-72-C2 CN-72-C5 WIRE-SAVING SYSTEMS * CN-74-C MEASUREMENT SENSORS Length: 1 m 3.281 ft 0.2 mm2 4-core cabtyre cable, with connector Length: 2 m 6.562 ft on one end Cable outer diameter: o3.3 mm o0.130 in Length: 5 m 16.404 ft CN-74-C2 Main cable 0.2 mm2 2-core cabtyre cable, with connector Length: 2 m 6.562 ft on one end Cable outer diameter: o3.3 mm o0.130 in Length: 5 m 16.404 ft STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS Sub cable PLC * CN-72-C HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS End plates End plates are not supplied with the amplifier. Please order them separately when the amplifiers are mounted in cascade. Appearance Model No. MS-DIN-E Description FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS When cascading multiple amplifiers, or when it moves depending on the way it is installed on a DIN rail, these end plates clamp amplifiers into place on both sides. Make sure to use end plates when cascading multiple amplifiers together. Two pcs. per set Selection Guide Fibers OPTIONS Fiber Amplifiers Amplifier mounting bracket Designation Model No. Amplifier mounting bracket MS-DIN-2 Mounting bracket for amplifier FX-MB1 10 sets of 2 communication window seals and 1 connector seal Communication window seal: It prevents malfunction due to transmission signal from another amplifier, as well as, prevents effect on another amplifier. Connector seal: It prevents contact of any metal, etc., with the pins of the quickconnection cable. Fiber amplifier protection seal Description Note: Fiber amplifier protection seals are supplied with the FX-301(P) and FX-305(P). * MS-DIN-2 FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F Fiber amplifier protection seal * FX-MB1 Communication window seal Connector seal 145 FIBER SENSORS Digital Fiber Sensor FX-300 SERIES LIST OF FIBERS LASER SENSORS FX-301 / FX-305 (Red LED type) sensing range (Note 1) PHOTOELECTRIC SENSORS Thru-beam type (one pair set) MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS The FX-305 and FX-301(-HS) have different sensing modes. FX-305: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-301(-HS): S-D, H-SP (Note 1), FAST, STD, LONG (no STDF or U-LG mode) Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. Sensing range (mm in) (Note 2) Model No. Red LED U-LG FT-140 LONG STDF STD Dimensions FAST 19,600 771.654 (Note 3) 19,600 771.654 (Note 3) 19,600 771.654 (Note 3) 16,000 629.921 16,000 629.921 H-SP 8,700 342.520 S-D 8,700 342.520 P.51 FT-30 450 17.717 310 12.205 210 8.268 150 5.906 110 4.331 60 2.362 60 2.362 P.51 FT-31 440 17.323 290 11.417 200 7.874 142 5.591 105 4.134 58 2.283 49 1.929 P.51 FT-31S 440 17.323 290 11.417 200 7.874 140 5.512 100 3.937 55 2.165 49 1.929 P.51 FT-31W 300 11.811 230 130 5.118 100 3.937 65 2.559 30 1.181 30 1.181 P.51 9.055 FT-40 1,300 51.181 900 35.433 600 23.622 450 17.717 330 12.992 180 7.087 180 7.087 P.51 FT-42 1,100 43.307 800 31.496 550 21.654 400 15.748 285 11.220 160 6.299 150 5.906 P.51 FT-42S 1,100 43.307 800 31.496 550 21.654 400 15.748 285 11.220 160 6.299 150 5.906 P.51 FT-42W 1,000 39.370 710 27.953 460 18.110 330 12.992 240 9.449 130 5.118 130 5.118 P.51 1,900 74.803 1,400 55.118 800 31.496 610 24.016 440 17.323 240 9.449 250 9.843 P.51 FT-45X 1,600 62.992 (Note 3) 1,100 43.307 780 30.709 570 22.441 410 16.142 230 9.055 230 9.055 P.52 STATIC ELECTRICITY PREVENTION DEVICES FT-A11 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 2,700 106.299 1,800 70.866 1,100 43.307 1,000 39.370 P.52 FT-A11W 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,100 122.047 2,300 90.551 1,200 47.244 1,200 47.244 P.52 LASER MARKERS FT-A32 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 2,900 114.173 2,900 114.173 P.52 FT-A32W 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 2,000 78.740 2,100 82.677 P.52 SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS PLC HUMAN MACHINE INTERFACES FT-43 FT-AL05 760 29.921 680 26.772 340 13.386 330 12.992 230 9.055 130 5.118 130 5.118 P.52 FT-E13 20 0.787 13 0.512 9 0.354 6 0.236 5 0.197 2 0.079 2 0.079 P.52 ENERGY CONSUMPTION VISUALIZATION COMPONENTS FT-E23 95 3.740 65 2.559 42 1.654 31 1.220 22 0.866 12 0.472 12 0.472 P.52 1,200 47.244 880 34.646 550 21.654 440 17.323 300 11.811 150 5.906 155 6.102 P.52 FA COMPONENTS FT-H20-J20-S (Note 4) 530 20.866 390 15.354 225 8.858 200 7.874 140 5.512 60 2.362 60 2.362 P.53 FT-H20-J30-S (Note 4) 530 20.866 390 15.354 225 8.858 200 7.874 140 5.512 60 2.362 60 2.362 P.53 FT-H20-J50-S (Note 4) 530 20.866 390 15.354 225 8.858 200 7.874 140 5.512 60 2.362 60 2.362 P.53 FT-H20-M1 750 29.528 550 21.654 320 12.598 280 11.024 200 7.874 85 3.346 90 3.543 P.53 FT-H20-VJ50-S (Note 4) 840 33.071 550 21.654 370 14.567 280 11.024 200 7.874 90 3.543 90 3.543 P.53 FT-H20-VJ80-S (Note 4) 840 33.071 550 21.654 370 14.567 280 11.024 200 7.874 90 3.543 90 3.543 P.53 FT-H20W-M1 420 16.535 310 12.205 180 7.087 140 5.512 100 3.937 40 1.575 50 1.969 P.53 FT-H30-M1V-S (Note 5) 350 250 150 5.906 125 4.921 90 3.543 50 1.969 40 1.575 P.53 FT-H35-M2 750 29.528 550 21.654 330 12.992 280 11.024 200 7.874 85 3.346 90 3.543 P.53 FT-H35-M2S6 750 29.528 550 21.654 330 12.992 280 11.024 200 7.874 85 3.346 90 3.543 P.53 FT-HL80Y 3,500 137.795 (Note 3) 3,500 137.795 (Note 3) 1,800 70.866 1,350 53.150 900 35.433 450 17.717 480 18.898 P.53 FT-KS40 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 2,700 106.299 1,900 74.803 1,000 39.370 850 33.465 P.54 120 MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F FT-H13-FM2 FT-KV26 13.78 9.843 710 27.953 340 13.386 310 12.205 4.724 P.54 FT-KV40 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,200 125.984 2,500 98.425 1,800 70.866 1,000 39.370 1,000 39.370 P.54 FT-KV40W 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 3,200 125.984 2,000 78.740 1,400 55.118 790 31.102 810 31.890 P.54 2,000 78.740 1,500 59.055 1,000 39.370 500 19.685 530 20.866 P.54 FT-L80Y 800 31.496 3,500 137.795 3,500 137.795 20 0.787 120 4.724 Notes: 1) Please contact our office about the sensing ranges for FX-301-HS in H-SP mode. 2) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) The fiber cable length practically limits the sensing range. 4) Heat-resistant joint fibers and ordinary-temperature fibers (FT-42) are sold as a set. 5) Sold as a set comprising vacuum type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8). Digital Fiber Sensor FX-300 SERIES LIST OF FIBERS FIBER SENSORS FX-301 / FX-305 (Red LED type) sensing range (Note 1) The FX-305 and FX-301(-HS) have different sensing modes. FX-305: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-301(-HS): S-D, H-SP (Note 1), FAST, STD, LONG (no STDF or U-LG mode) Thru-beam type (one pair set) Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. Model No. Red LED U-LG LONG STDF STD FAST H-SP AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS S-D 340 13.386 290 11.417 150 5.118 95 3.740 49 1.929 49 1.929 P.54 FT-R40 1,000 39.370 710 27.953 470 18.504 330 12.992 240 9.449 130 5.118 130 5.118 P.54 FT-R41W 1,000 39.370 710 27.953 460 18.110 330 12.992 240 9.449 130 5.118 130 5.118 P.54 FT-R42W 2,800 110.236 1,600 62.992 890 35.039 770 30.315 560 22.047 310 12.205 320 12.598 P.54 FT-R43 1,000 39.370 710 27.953 450 17.717 290 11.417 210 8.268 110 4.331 110 4.331 P.54 FT-R44Y 1,000 39.370 710 27.958 450 17.717 290 11.417 210 8.268 110 4.330 110 4.330 P.55 FT-R60Y 2,650 104.330 1,800 70.866 1,200 47.244 830 32.677 610 24.016 350 13.780 P.55 100 FT-S20 130 335 13.189 3.150 50 1.969 31 1.220 22 0.866 13 0.512 14 0.551 P.55 450 17.717 310 12.205 210 8.268 150 5.906 110 4.331 60 2.362 60 2.362 P.55 FT-S21 440 17.323 290 11.417 200 7.874 142 5.591 105 4.134 58 2.283 49 1.929 P.55 FT-S21W 300 11.811 230 130 5.118 100 3.937 65 2.559 30 1.181 30 1.181 P.55 3.937 80 9.055 PHOTOELECTRIC SENSORS Dimensions FT-R31 5.906 LASER SENSORS MICRO PHOTOELECTRIC SENSORS Sensing range (mm in) (Note 2) FT-S11 146 PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS FT-S30 1,300 51.181 900 35.433 600 23.622 450 17.717 330 12.992 180 7.087 180 7.087 P.55 FT-S31W 1,000 39.370 710 27.953 460 18.110 330 12.992 240 130 5.118 130 5.118 P.55 STATIC ELECTRICITY PREVENTION DEVICES FT-S32 3,600 141.732 2,400 94.488 1,500 59.055 1,100 43.307 510 20.079 P.55 LASER MARKERS FT-V23 590 23.228 380 14.961 270 10.630 FT-V24W 120 4.724 90 3.543 55 FT-V25 310 12.205 200 7.874 130 FT-V30 620 24.409 FT-V40 FT-V80Y 9.449 840 33.071 460 18.110 170 6.693 125 4.921 60 2.362 63 2.480 P.55 2.165 40 1.575 30 1.181 13 0.512 15 0.591 P.56 5.118 90 3.543 60 2.362 35 1.378 35 1.378 P.56 420 16.535 270 10.630 200 7.874 140 5.512 70 2.756 70 2.756 P.56 3,600 141.732 (Note 3) 3,600 141.732 (Note 3) 1,600 62.992 1,700 66.929 1,200 47.244 680 26.772 690 27.165 P.56 ENERGY CONSUMPTION VISUALIZATION COMPONENTS 280 11.024 120 4.724 140 5.512 P.56 FA COMPONENTS MACHINE VISION SYSTEMS 1,000 39.370 800 31.496 500 19.685 400 15.748 FT-Z20HBW 400 15.748 290 11.417 160 6.299 130 5.118 90 3.543 50 1.969 50 1.969 P.56 FT-Z20W 830 32.677 570 22.441 370 14.567 250 9.843 180 7.087 90 3.543 90 3.543 P.56 2,600 102.362 1,900 74.803 1,100 43.307 850 33.465 620 24.409 330 12.992 340 13.386 P.56 FT-Z30E 3,600 141.732 (Note 3) 3,100 122.047 2,100 82.677 1,600 62.992 1,100 43.307 650 25.591 670 26.378 P.56 FT-Z30EW 3,600 141.732 (Note 3) 2,700 106.299 1,400 55.118 1,200 47.244 900 35.433 500 19.685 500 19.685 P.57 FT-Z30H 3,600 141.732 (Note 3) 3,100 122.047 2,200 86.614 1,600 62.992 1,100 43.307 650 25.591 670 26.378 P.57 FT-Z30HW FT-Z30 3,600 141.732 (Note 3) 3,100 122.047 2,200 86.614 1,500 59.055 1,000 39.370 590 23.228 610 24.016 P.57 FT-Z30W 2,000 78.740 1,400 55.118 890 35.039 640 25.197 460 18.110 250 9.843 260 10.236 P.57 FT-Z40HBW 1,000 39.370 710 27.953 460 18.110 330 12.992 240 9.449 130 5.118 130 5.118 P.57 FT-Z40W 1,900 74.803 1,300 51.181 900 35.433 630 24.803 460 18.110 240 9.449 260 10.236 P.57 FT-Z802Y 3,500 137.795 3,500 137.795 3,000 118.110 1,500 59.055 1,000 39.370 500 19.685 530 20.866 P.57 Notes: 1) Please contact our office about the sensing ranges for FX-301-HS in H-SP mode. 2) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) The fiber cable length practically limits the sensing range. PLC HUMAN MACHINE INTERFACES UV CURING SYSTEMS Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F 147 FIBER SENSORS Digital Fiber Sensor FX-300 SERIES LIST OF FIBERS LASER SENSORS FX-301 / FX-305 (Red LED type) sensing range (Note 1) PHOTOELECTRIC SENSORS Retroreflective type MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS The FX-305 and FX-301(-HS) have different sensing modes. FX-305: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-301(-HS): S-D, H-SP (Note 1), FAST, STD, LONG (no STDF or U-LG mode) Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. Sensing range (mm in) (Note 2, 3) Red LED STDF STD FAST Model No. U-LG LONG Dimensions H-SP S-D FR-KZ22E 15 to 370 0.591 to 14.567 15 to 330 0.591 to 12.992 15 to 240 0.591 to 9.449 15 to 210 0.591 to 8.268 15 to 170 0.590 to 6.693 15 to 80 0.591 to 3.150 15 to 90 0.591 to 3.543 P.58 FR-KZ50E 20 to 350 0.787 to 13.780 20 to 300 0.787 to 11.811 20 to 250 0.787 to 9.843 20 to 200 0.787 to 7.874 20 to 200 0.787 to 7.874 20 to 200 0.787 to 7.874 20 to 200 0.787 to 7.874 P.58 FR-KZ50H 20 to 350 0.787 to 13.780 20 to 300 0.787 to 11.811 20 to 250 0.787 to 9.843 20 to 200 0.787 to 7.874 20 to 200 0.787 to 7.874 20 to 200 0.787 to 7.874 20 to 200 0.787 to 7.874 P.58 FR-Z50HW 100 to 920 3.937 to 36.220 100 to 810 3.937 to 31.890 100 to 660 3.937 to 25.984 100 to 580 3.937 to 22.835 100 to 490 3.937 to 19.291 100 to 340 3.937 to 13.385 100 to 270 3.937 to 10.630 P.58 Notes: 1) Please contact our office about the sensing ranges for FX-301-HS in H-SP mode. 2) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. The sensing range of FR-KZ22E is specified for the attached reflector. The sensing range of FR-KZ50E and FR-KZ50H is specified for the attached reflector RF-003. The sensing range of FR-Z50HW is specified for the RF-13. 3) The sensing range is the possible setting range for the attached reflector. The fiber can detect an object less than setting range for the reflector. However, note that if there are any white or highly-reflective surfaces near the fiber head, reflected incident light may affect the fiber head. If this occurs, adjust the threshold value of the amplifier unit before use. WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS Sensing range when using in combination with FR-Z50HW reflector (Optional) The sensing ranges are the value for red LED types. Sensing range (mm in) Reflector Model No. FX-301 / 305 U-LG LONG STDF STD FX-301-HS FAST S-D H-SP H-SP RF-230 100 to 7,500 3.937 to 295.276 100 to 3,200 3.937 to 125.984 100 to 2,900 3.937 to 114.173 100 to 2,000 3.937 to 78.740 100 to 1,600 3.937 to 62.992 100 to 1,000 3.937 to 39.370 100 to 900 3.937 to 35.433 100 to 700 3.937 to 27.559 RF-220 100 to 2,400 3.937 to 94.488 100 to 2,400 3.937 to 94.488 100 to 1,900 3.937 to 74.803 100 to 1,300 3.937 to 51.181 100 to 1,000 3.937 to 39.370 100 to 600 3.937 to 23.622 100 to 570 3.937 to 22.441 100 to 350 3.937 to 13.780 RF-210 100 to 2,100 3.937 to 82.677 100 to 1,700 3.937 to 66.929 100 to 1,300 3.937 to 51.181 100 to 910 3.937 to 35.827 100 to 710 3.937 to 27.953 100 to 460 3.937 to 18.110 100 to 440 3.937 to 17.323 - Note: The sensing range is the possible setting range for the reflector. The fiber can detect an object less than setting range for the reflector. However, note that if there are any white or highly-reflective surfaces near the fiber head, reflected incident light may affect the fiber head. If this occurs, adjust the threshold value of the amplifier unit before use. FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS FX-301 / FX-305 (Red LED type) sensing range (Note 1) The FX-305 and FX-301(-HS) have different sensing modes. FX-305: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-301(-HS): S-D, H-SP (Note 1), FAST, STD, LONG (no STDF or U-LG mode) Reflective type Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. Model No. U-LG LONG Sensing range (mm in) (Note 2, 3) / Description Red LED STDF STD FAST Dimensions H-SP S-D FD-30 170 6.693 110 4.331 70 2.756 50 1.969 40 1.575 20 0.787 18 0.709 P.59 FD-31 150 5.906 95 3.740 63 2.480 45 1.772 35 1.378 17 0.669 16 0.630 P.59 FD-31W 60 2.362 40 1.575 30 1.181 20 0.787 15 0.591 8 0.315 10 0.394 P.59 FD-32G 210 8.268 120 4.724 100 3.937 60 2.362 42 1.654 20 0.787 20 0.787 P.59 FX-500 FD-32GX 240 9.449 140 5.512 100 3.937 70 2.756 50 1.969 25 0.984 25 0.984 P.59 FX-100 FD-40 170 6.693 110 4.331 70 2.756 50 1.969 40 1.575 20 0.787 18 0.709 P.59 FX-300 FD-41 150 5.906 95 3.740 63 2.480 45 1.772 35 1.378 17 0.669 16 0.630 P.59 FX-410 FD-41S 150 5.906 95 3.740 63 2.480 45 1.772 35 1.378 17 0.669 16 0.630 P.59 FX-311 FD-41SW 60 2.362 40 1.575 30 1.181 20 0.787 15 0.591 8 0.315 10 0.394 P.59 FD-41W 300 11.811 220 8.661 140 5.512 95 3.740 70 2.756 35 1.378 40 1.575 P.59 FD-42G 210 8.268 120 4.724 100 3.937 60 2.362 42 1.654 20 0.787 20 0.787 P.60 FD-42GW 160 6.299 85 3.346 70 2.756 35 1.378 25 0.984 13 0.512 14 0.551 P.60 FD-60 500 19.685 350 13.780 240 9.449 160 6.299 130 5.118 70 2.756 70 2.756 P.60 FD-61 440 17.323 320 12.598 205 8.071 145 5.709 105 4.134 65 2.559 60 2.362 P.60 FD-61G 460 18.110 200 7.874 210 8.268 90 3.543 65 2.559 35 1.378 40 1.575 P.60 FD-61S 440 17.323 320 12.598 205 8.071 145 5.709 105 4.134 60 2.362 60 2.362 P.60 Selection Guide Fibers Fiber Amplifiers FX-301-F7/ FX-301-F Notes: 1) Please contact our office about the sensing ranges for FX-301-HS in H-SP mode. 2) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) The sensing range is specified for white non-glossy paper. Digital Fiber Sensor FX-300 SERIES LIST OF FIBERS 148 FIBER SENSORS FX-301 / FX-305 (Red LED type) sensing range (Note 1) The FX-305 and FX-301(-HS) have different sensing modes. FX-305: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-301(-HS): S-D, H-SP (Note 1), FAST, STD, LONG (no STDF or U-LG mode) Reflective type Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. Model No. U-LG LONG FD-61W 300 11.811 220 FD-62 690 27.165 FD-64X Sensing range (mm in) (Note 2, 3) / Description Red LED STDF STD FAST H-SP Dimensions AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS S-D 95 3.740 70 2.756 35 1.378 40 1.575 P.60 480 18.898 310 12.205 220 8.661 160 6.299 85 3.346 90 3.543 P.60 270 10.630 200 7.874 100 3.937 85 3.346 60 2.362 35 1.378 35 1.378 P.61 FD-A16 230 9.055 200 7.874 150 5.906 150 5.906 100 3.937 45 1.772 50 1.969 P.61 FD-AL11 360 14.173 250 9.843 160 6.299 110 4.331 80 3.150 40 1.575 40 1.575 P.61 140 PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS 5.512 8.661 LASER SENSORS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS FD-E13 15 0.591 11 0.433 7 0.276 6 0.236 4 0.157 2 0.079 2 0.079 P.61 FD-E23 65 2.559 45 1.772 28 1.102 19 0.748 14 0.551 7 0.276 7 0.276 P.61 SENSOR OPTIONS FD-EG30 60 2.362 45 1.772 25 0.984 19 0.748 14 0.551 7 0.276 7 0.276 P.61 FD-EG30S 60 2.362 45 1.772 25 0.984 19 0.748 14 0.551 7 0.276 7 0.276 P.62 SIMPLE WIRE-SAVING UNITS FD-EG31 20 0.787 15 0.591 9 0.354 8 0.315 5 0.197 2.5 0.098 3 0.118 P.62 WIRE-SAVING SYSTEMS Applicable pipe diameter: Outer dia. o6 to o26 mm o0.236 to o1.024 in transparent pipe [PFA (fluorine resin) or equivalently transparent pipe, wall thickness 1 mm 0.039 in] P.62 MEASUREMENT SENSORS Applicable pipe diameter: Outer dia. o6 to o26 mm o0.236 to o1.024 in transparent pipe [PVC (vinyl chloride), fluorine resin, polycarbonate, acrylic, glass, wall thickness 1 to 3 mm 0.039 to 0.118 in] P.62 STATIC ELECTRICITY PREVENTION DEVICES o4 mm o0.157 in form Protective tube: fluorine resin, length 500 mm 19.685 in (cuttable) Liquid surface not contacted: Beam received, Liquid surface contacted: Beam interrupted P.62 LASER MARKERS P.62 PLC P.62 HUMAN MACHINE INTERFACES 1.850 P.63 ENERGY CONSUMPTION VISUALIZATION COMPONENTS 2 to 6 0.079 to 0.236 P.63 FA COMPONENTS FD-F4 FD-F41 FD-F41Y FD-F8Y - - FD-FA93 FD-H13-FM2 FD-H18-L31 - - - - - Applicable pipe diameter: Outer dia. o8 mm o0.315 in or more transparent pipe (When used with the tying bands: o8 to o80 mm o0.315 to o3.150 in) [PFA (fluorine resin), including translucent] Liquid absent: Beam received, Liquid present: Beam interrupted 410 16.142 0 to 20 0 to 0.787 310 12.205 0 to 15 0 to 0.591 200 7.874 0 to 10 0 to 0.394 140 5.512 100 3.937 0 to 10 0 to 0.394 1 to 8 0.039 to 0.315 55 2.165 Cannot use 47 FD-H20-21 300 11.811 270 10.630 150 5.906 140 5.512 100 3.937 35 1.378 47 1.850 P.63 FD-H20-M1 300 11.811 270 10.630 150 5.906 140 5.512 100 3.937 35 1.378 47 1.850 P.63 FD-H25-L43 (Note 5) 3 to 28 0.118 to 1.102 3 to 25 0.118 to 0.984 4 to 23 0.157 to 0.906 4 to 20 0.118 to 0.787 4 to 19 0.118 to 0.748 4 to 16 0.118 to 0.630 4 to 16 0.118 to 0.630 P.63 - - P.63 FD-H30-KZ1V-S (Note 5,6) 20 to 300 0.787 to 11.811 20 to 200 0.787 to 7.874 20 to 150 0.787 to 5.906 25 to 130 0.984 to 5.118 30 to 100 1.181 to 3.937 Cannot use Cannot use P.64 FD-H30-L32 0 to 20 0 to 0.787 0 to 15 0 to 0.591 0 to 10 0 to 0.394 0 to 10 0 to 0.394 1 to 8 0.039 to 0.315 Cannot use 2 to 6 0.079 to 0.236 P.64 FD-H30-L32V-S (Note 5,6) 0 to 11 0 to 0.433 0 to 8 0 to 0.315 1.5 to 6 0.059 to 0.236 1.5 to 5 0.059 to 0.197 2 to 4 0.079 to 0.157 Cannot use Cannot use P.64 FD-H25-L45 (Note 5) 5 to 42 0.197 to 1.654 6 to 41 0.236 to 1.614 6 to 40 0.236 to 1.575 7 to 38 0.276 to 1.496 - FD-H35-20S 190 7.480 160 6.299 80 3.150 80 3.150 57 2.244 20 0.787 26 1.024 P.64 FD-H35-M2 300 11.811 270 10.630 150 5.906 140 5.512 100 3.937 35 1.378 47 1.850 P.64 FD-H35-M2S6 300 11.811 270 10.630 150 5.906 140 5.512 100 3.937 35 1.378 47 1.850 P.64 FD-HF40Y (Note 4) o4 mm o0.157 in form Protective tube: fluorine resin, length:500 mm 19.685 in (allowable cutting) Liquid surface not contacted: Beam received, Liquid surface contacted: Beam interrupted P.64 MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Fibers Fiber Amplifiers FX-500 0 to 4 0 to 0.157 0 to 3.8 0 to 0.150 0 to 3.5 0 to 0.138 0 to 3.5 0 to 0.138 P.65 FX-100 0 to 7 0 to 0.906 0 to 7 0 to 0.276 P.65 FX-300 FD-L12W (Note 5) 0.5 to 9 0.020 to 0.354 0.5 to 8 0.019 to 0.315 1 to 6.5 0.039 to 0.256 1 to 5.5 0.039 to 0.217 1 to 5 0.039 to 0.197 P.65 FX-410 FD-L10 (Note 5) FD-L11 (Note 5) 0 to 4.7 0 to 0.185 0 to 4.5 0 to 0.177 0 to 4.5 0 to 0.177 0 to 9 0 to 0.354 0 to 8 0 to 0.315 0 to 8 0 to 0.315 0 to 6 0 to 0.236 - 0 to 6 0 to 0.236 - FD-L20H 1 to 29 0.039 to 1.142 2 to 23 0.079 to 0.906 3 to 17 0.118 to 0.669 4 to 14 0.157 to 0.551 4.5 to 11 0.177 to 0.433 5 to 8.5 0.196 to 0.335 4.8 to 9.5 0.188 to 0.374 P.65 FD-L21 (Note 5) 2 to 19 0.079 to 0.748 2 to 18 0.079 to 0.709 2 to 16 0.079 to 0.748 3 to 16 0.118 to 0.630 3 to 15 0.118 to 0.591 4 to 11 0.157 to 0.433 5 to 11 0.197 to 0.433 P.65 FD-L21W (Note 5) 3 to 14.5 0.118 to 0.571 3 to 14 0.118 to 0.551 4 to 14 0.157 to 0.551 6 to 12 0.236 to 0.472 7 to 12 0.276 to 0.472 FD-L22A (Note 5) - - 0 to 26 0 to 1.024 0 to 23 0 to 0.906 0 to 23 0 to 0.906 0 to 23 0 to 0.906 0 to 19 0 to 0.748 1 to 17 0.039 to 0.669 1 to 17 0.039 to 0.669 P.65 P.65 Notes: 1) Please contact our office about the sensing ranges for FX-301-HS in H-SP mode. 2) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) The sensing range of reflective type is the value for white non-glossy paper (as for FD-H30-L32 and FD-H18-L31 50 x 50 mm 1.969 x 1.969 in glass substrate). 4) Liquid inflow prevention joint, protective tube extension joint, fiber mounting joint are available. Please refer to p.38 for details. 5) The sensing range is specified for transparent glass 100 x 100 x t0.7 mm 3.937 x 3.937 x t0.028 in (FD-L21 and FD-L21W: t2 mm t0.079 in) [FD-L10: silicon wafers 100 x 100 mm 3.937 x 3.937 in]. 6) Sold as a set comprising vacuum type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8). FX-311 FX-301-F7/ FX-301-F 149 FIBER SENSORS Digital Fiber Sensor FX-300 SERIES LIST OF FIBERS LASER SENSORS FX-301 / FX-305 (Red LED type) sensing range (Note 1) PHOTOELECTRIC SENSORS Reflective type MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. Model No. U-LG Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F LONG Sensing range (mm in) (Note 2, 3) / Description Red LED STDF STD FAST Dimensions H-SP S-D FD-L23 (Note 4) 0 to 30 0 to 1.181 0 to 30 0 to 1.181 0 to 30 0 to 1.181 0 to 30 0.039 to 1.181 1 to 28 0.039 to 1.102 2 to 27 0.079 to 1.063 2 to 27 0.079 to 1.063 P.65 FD-L30A (Note 4) 0 to 50 0 to 1.969 0 to 43 0 to 17.441 0 to 40 0 to 1.575 0 to 37 0 to 1.457 0 to 32 0 to 1.260 0 to 26 0 to 1.024 0 to 26 0 to 1.024 P.65 FD-L31A (Note 4) 4 to 33 0 to 13.110 4 to 33 0.157 to 1.299 5 to 32 0 to 1.260 5 to 32 0.197 to 1.260 5 to 32 0.197 to 1.259 6 to 18 0.236 to 0.709 6 to 18 0.236 to 0.709 P.65 FD-L32H (Note 4) 0 to 60 0 to 2.362 0 to 50 0 to 1.969 0 to 36 0 to 0.984 15 to 35 0.591 to 1.378 16 to 29 0.630 to 1.142 FD-R31G - - P.66 160 6.299 92 3.622 75 2.953 44 1.732 32 1.260 17 0.669 17 0.669 P.66 FD-R32EG 60 2.362 45 1.772 25 0.984 19 0.748 13 0.512 7 0.276 7 0.276 P.66 FD-R33EG 17 0.669 15 0.591 8 0.315 6 0.236 4 0.157 2 0.079 2 0.079 P.66 FD-R34EG 51 2.008 38 1.496 21 0.827 16 0.630 11 0.433 6 0.236 6 0.236 P.66 FD-R41 230 9.055 150 5.906 100 3.937 70 2.756 50 1.969 28 1.102 28 1.102 P.66 FD-R60 310 12.205 240 9.449 170 6.693 120 4.724 90 3.543 45 1.772 45 1.772 P.66 FD-R61Y 350 13.780 230 9.055 160 6.299 110 4.330 80 3.150 45 1.772 45 1.772 P.66 FD-S21 80 3.150 50 1.969 40 1.575 25 0.984 19 0.748 9 0.354 9 0.354 P.66 FD-S30 170 6.693 110 4.331 70 2.756 50 1.969 40 1.575 20 0.787 18 0.709 P.67 FD-S31 150 5.906 95 3.740 63 2.480 45 1.772 35 1.378 17 0.669 16 0.630 P.67 FD-S32 440 17.323 270 10.630 200 7.874 140 5.512 100 3.937 55 2.165 55 2.165 P.67 FD-S32W 300 11.811 220 8.661 140 5.512 95 3.740 70 2.756 35 1.378 40 1.575 P.67 FD-S33GW 160 85 3.346 70 2.756 35 1.378 25 0.984 13 0.512 14 0.551 P.67 FD-S60Y 410 16.142 360 14.173 FD-V30 FD-V30W FD-V50 FD-Z20HBW FD-Z20W 6.299 250 9.843 170 6.693 120 4.724 65 2.559 70 2.756 P.67 45 1.772 30 1.181 20 0.787 15 0.591 6 0.236 7 0.276 P.67 0.984 15 0.591 10 0.394 7 0.276 5 0.197 6.693 100 3.937 55 2.165 45 1.772 32 1.260 80 3.150 25 170 - - P.67 0.630 P.68 1 to 70 0.039 to 2.756 1 to 70 0.039 to 2.756 1 to 32.2 0.039 to 1.268 2 to 30 0.079 to 1.181 2.5 to 20 0.098 to 0.787 3 to 10 0.118 to 0.394 3 to 10 0.118 to 0.394 P.68 1 to 87 0.039 to 3.425 1 to 59 0.0.9 to 2.323 2 to 39 0.079 to 1.535 3 to 27 0.118 to 1.063 3 to 19 0.118 to 0.748 15 0.591 - 16 - P.68 FD-Z40HBW 350 13.780 0.5 to 230 0.02 to 9.055 1 to 160 0.039 to 6.299 1 to 100 0.039 to 3.937 1 to 70 0.039 to 2.756 1 to 40 0.039 to 1.575 1 to 40 0.039 to 1.575 P.68 FD-Z40W 270 10.630 4.724 1 to 87 0.039 to 3.425 1 to 63 0.039 to 2.480 2.5 to 32 0.098 to 1.260 2.5 to 32 0.098 to 1.260 P.68 10 to 870 0.394 to 34.252 10 to 540 0.394 to 21.260 10 to 400 0.394 to 15.748 10 to 250 0.393 to 9.843 10 to 190 0.394 to 7.480 15 to 100 0.196 to 3.937 15 to 100 0.591 to 3.937 P.68 FD-Z50HW Selection Guide The FX-305 and FX-301(-HS) have different sensing modes. FX-305: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-301(-HS): S-D, H-SP (Note 1), FAST, STD, LONG (no STDF or U-LG mode) 180 7.087 120 Notes: 1) Please contact our office about the sensing ranges for FX-301-HS in H-SP mode. 2) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) The sensing range of reflective type is the value for white non-glossy paper. 4) The sensing range is specified for transparent glass 100 x 100 x t0.7 mm 3.937 x 3.937 x t0.028 in (FD-L32H: R edge). Digital Fiber Sensor FX-300 SERIES SENSING RANGE OF BLUE LED / GREEN LED / INFRARED LED FIBER SENSORS LASER SENSORS Thru-beam type (One pair set) Fibers are listed in alphabetic order. Refer to p.5~ for details of each fiber. PHOTOELECTRIC SENSORS Sensing range (mm in) (Note 1) FX-301B / 311B Model No. LONG FT-140 150 STD FX-301G / 311G FAST LONG STD FX-301H (Note 2) FAST LONG STD Dimensions AREA SENSORS FAST 8,100 318.898 4,000 157.480 3,100 122.047 5,000 196.850 2,400 94.488 1,600 62.992 3,700 145.669 2,000 78.740 1,400 55.118 MICRO PHOTOELECTRIC SENSORS P.51 LIGHT CURTAINS / SAFETY COMPONENTS FT-30 55 2.165 28 1.102 18 0.709 28 1.102 13 0.512 9 0.354 25 0.984 13 0.512 9 0.354 P.51 FT-31 50 1.969 25 0.984 16 0.630 24 0.945 12 0.472 8 0.315 23 0.906 11 0.433 8 0.315 P.51 FT-31S 50 1.969 25 0.984 16 0.630 24 0.945 12 0.472 8 0.315 23 0.906 11 0.433 8 0.315 P.51 FT-31W 31 1.220 15 0.591 10 0.394 15 0.591 8 0.315 5 0.197 18 0.709 8 0.315 5 0.197 P.51 FT-40 155 6.102 76 2.992 45 1.772 90 3.543 40 1.575 26 1.024 80 3.150 43 1.693 27 1.063 P.51 FT-42 150 5.906 75 2.953 40 1.575 80 3.150 35 1.378 24 0.945 75 2.953 40 1.575 25 0.984 P.51 FT-42S 150 5.906 75 2.953 40 1.575 70 2.756 35 1.378 24 0.945 75 2.953 40 1.575 25 0.984 P.51 FT-42W 110 4.331 50 1.969 30 1.181 56 2.205 28 1.102 20 0.787 64 2.520 32 1.260 21 0.827 P.51 FT-43 220 8.661 110 4.331 75 2.953 120 4.724 61 2.402 43 1.693 140 5.512 74 2.913 48 1.890 P.51 FT-45X 130 5.118 65 2.559 45 1.772 70 2.756 34 1.339 25 0.984 160 6.299 79 3.110 53 2.087 P.52 FT-A11 880 34.646 420 16.535 270 10.630 430 16.929 220 8.661 120 4.724 500 19.685 220 8.661 120 4.724 P.52 FT-A11W 820 32.283 420 16.535 280 11.024 460 18.110 220 8.661 140 5.512 520 20.472 240 9.449 140 5.512 P.52 FT-A32 1,800 70.866 710 27.953 400 15.748 970 38.189 320 12.598 180 7.087 910 35.827 340 13.386 150 5.906 P.52 STATIC ELECTRICITY PREVENTION DEVICES FT-A32W 2,000 78.740 830 32.677 420 16.535 1,000 39.370 350 13.780 180 7.087 910 35.827 340 13.386 150 5.906 P.52 LASER MARKERS 100 3.937 48 1.890 18 0.709 54 2.126 27 1.063 18 0.709 P.52 FT-E13 2 0.079 1 0.039 2 0.079 1 0.039 FT-E23 8 0.315 4 0.157 3 0.118 4 0.157 2 0.079 1 0.039 10 0.394 5 0.197 3 0.118 P.52 FT-H13-FM2 72 2.835 36 1.417 26 1.024 32 1.260 16 0.630 10 0.394 70 2.756 35 1.378 25 0.984 P.52 FT-H20-J20-S (Note 3) 60 2.362 20 0.787 - 35 1.378 - - 20 0.787 - - P.53 ENERGY CONSUMPTION VISUALIZATION COMPONENTS 35 1.378 - - 20 0.787 - - P.53 FA COMPONENTS 35 1.378 - - 20 0.787 - - P.53 280 11.024 160 6.299 P.53 30 1.181 - - P.53 30 1.181 - - P.53 FT-AL05 32 1.260 - 56 2.205 1 0.039 27 1.063 - - FT-H20-J30-S (Note 3) 60 2.362 20 0.787 - FT-H20-J50-S (Note 3) 60 2.362 20 0.787 - 100 3.937 50 1.969 FT-H20-VJ50-S (Note 3) 85 3.346 30 1.181 - 50 1.969 - - FT-H20-VJ80-S (Note 3) 85 3.346 30 1.181 - 50 1.969 - - FT-H20W-M1 44 1.732 22 0.866 FT-H20-M1 35 1.378 14 0.551 22 0.866 25 0.984 11 0.433 7 0.276 220 8.661 100 3.937 70 2.756 - - P.53 FT-H35-M2 50 1.969 35 1.378 50 1.969 25 0.984 18 0.709 550 21.654 280 11.024 160 6.299 P.53 FT-H35-M2S6 100 3.937 50 1.969 35 1.378 50 1.969 25 0.984 18 0.709 550 21.654 280 11.024 160 6.299 P.53 80 3.150 40 1.575 25 0.984 110 4.331 55 2.165 40 1.575 1,100 43.307 550 21.654 350 13.780 P.53 FT-KS40 740 29.134 280 11.024 220 8.661 420 16.535 180 7.087 81 3.189 460 18.110 190 7.480 95 3.740 P.54 FT-KV26 81 3.189 36 1.417 21 0.827 44 1.732 8 0.315 53 2.087 19 0.748 FT-KV40 710 27.953 270 10.630 210 8.268 420 16.535 180 7.087 100 3.937 290 11.417 120 4.724 53 2.087 P.54 FT-KV40W 860 33.858 400 15.748 260 10.236 420 16.535 210 8.268 140 5.512 490 19.291 240 9.449 140 5.512 P.54 FT-L80Y 160 6.299 80 3.150 50 1.969 160 6.299 80 3.150 50 1.969 400 15.748 200 7.874 150 5.906 P.54 FT-R31 45 1.772 23 0.906 15 0.591 24 0.945 12 0.472 8 0.315 23 0.906 11 0.433 8 0.315 P.54 FT-R40 110 4.331 54 2.126 36 1.417 55 2.165 26 1.024 20 0.787 58 2.283 30 1.181 20 0.787 P.54 FT-R41W 110 4.331 50 1.969 30 1.181 56 2.205 28 1.102 20 0.787 64 2.520 32 1.260 21 0.827 P.54 FT-R42W 280 11.024 130 5.118 90 3.543 140 5.512 70 2.756 47 1.850 140 5.512 70 2.756 47 1.850 P.54 - 20 0.787 - INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS PLC HUMAN MACHINE INTERFACES MACHINE VISION SYSTEMS UV CURING SYSTEMS P.53 20 0.787 FT-HL80Y - 550 21.654 40 1.575 20 0.787 - 18 0.709 P.52 100 3.937 FT-H30-M1V-S (Note 4) - 50 1.969 - PRESSURE / FLOW SENSORS P.54 Notes: 1) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 2) Because infrared types are easily affected by humidity, please ask assistance when using them in a humid environment or in an environment with varying humidity. 3) Heat-resistant joint fibers and ordinary-temperature fibers (FT-42) are sold as a set. 4) Sold as a set comprising vacuum type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8). Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F 151 FIBER SENSORS Digital Fiber Sensor FX-300 SERIES SENSING RANGE OF BLUE LED / GREEN LED / INFRARED LED LASER SENSORS Thru-beam type (One pair set) PHOTOELECTRIC SENSORS Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. MICRO PHOTOELECTRIC SENSORS Sensing range (mm in) (Note 1) LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS FX-301B / 311B Model No. AREA SENSORS LONG FX-301G / 311G STD FAST LONG FX-301H (Note 2) STD FAST LONG 96 3.780 50 1.969 33 1.299 53 2.087 25 0.984 17 0.669 55 2.165 27 1.063 18 0.709 P.54 FT-R44Y 96 3.780 50 1.969 33 1.299 53 2.087 25 0.984 17 0.669 55 5.165 27 1.063 18 0.709 P.55 FT-R60Y 250 9.843 120 4.724 80 3.150 140 5.512 70 2.756 50 1.969 60 2.362 90 3.543 170 6.693 P.55 FT-S11 12 0.472 5 0.197 4 0.157 5 0.197 2.5 0.098 1.5 0.059 21 0.827 10 0.394 7 0.276 P.55 FT-S20 55 2.165 28 1.102 18 0.709 28 1.102 13 0.512 9 0.354 25 0.984 13 0.512 9 0.354 P.55 FT-S21 50 1.969 25 0.984 16 0.630 24 0.945 12 0.472 8 0.315 23 0.906 11 0.433 8 0.315 P.55 FT-S21W 31 1.220 15 0.591 10 0.394 15 0.591 8 0.315 5 0.197 18 0.709 8 0.315 5 0.197 P.55 FT-S30 155 6.102 76 2.992 45 1.772 90 3.543 40 1.575 26 1.024 80 3.150 43 1.693 27 1.063 P.55 FT-S31W 110 4.331 50 1.969 30 1.181 56 2.205 28 1.102 20 0.787 64 2.520 32 1.260 21 0.827 P.55 FT-S32 420 16.535 200 7.874 130 5.118 220 8.661 100 3.937 72 2.835 210 8.268 100 3.937 67 2.638 P.55 FT-V23 65 2.559 26 1.024 18 0.709 26 1.024 13 0.512 8 0.315 29 1.142 13 0.512 9 0.354 P.55 FT-V24W 6 0.236 2 0.079 25 0.984 12 0.472 - 3 0.118 - - 3 0.118 FT-V25 FT-V30 80 3.150 40 1.575 22 0.866 40 1.575 14 0.551 8 0.315 47 1.850 LASER MARKERS FT-V40 400 15.748 200 7.874 130 5.118 200 7.874 100 3.937 65 2.559 290 11.417 FT-V80Y 120 4.724 60 2.362 35 1.378 80 3.150 40 1.575 25 0.984 75 2.953 FT-Z20HBW 39 1.535 19 0.748 12 0.472 20 0.787 10 0.394 6 0.236 FT-Z20W 82 3.228 37 1.457 23 0.906 44 1.732 18 0.709 HUMAN MACHINE INTERFACES FAST FT-R43 STATIC ELECTRICITY PREVENTION DEVICES PLC Dimensions STD 9 0.354 16 0.630 7 0.276 - - P.56 4 0.157 P.56 19 0.748 9 0.354 P.56 140 5.512 92 3.622 P.56 38 1.496 24 0.945 P.56 40 1.575 15 0.591 12 0.472 P.56 11 0.433 100 3.937 50 1.969 32 1.260 P.56 5 0.197 15 0.591 8 0.315 ENERGY CONSUMPTION VISUALIZATION COMPONENTS FT-Z30 120 4.724 60 2.362 40 1.575 96 3.780 45 1.772 30 1.181 140 5.512 72 2.835 47 1.850 P.56 FT-Z30E 540 21.260 250 9.843 170 6.693 270 10.630 130 5.118 91 3.583 280 11.024 140 5.512 88 3.465 P.56 FA COMPONENTS FT-Z30EW 540 21.260 260 10.236 170 6.693 260 10.236 120 4.724 88 3.465 290 11.417 140 5.512 92 3.622 P.57 FT-Z30H 650 25.591 310 12.205 200 7.874 340 13.386 160 6.299 110 4.331 330 12.992 160 6.299 100 3.937 P.57 FT-Z30HW 540 21.260 260 10.236 170 6.693 260 10.236 120 4.724 88 3.465 290 11.417 140 5.512 92 3.622 P.57 83 3.268 40 1.575 25 0.984 73 2.874 36 1.417 25 0.984 100 3.937 52 2.047 34 1.339 P.57 FT-Z40HBW 110 4.331 50 1.969 30 1.181 56 2.205 28 1.102 20 0.787 64 2.520 32 1.260 21 0.827 P.57 FT-Z40W 180 7.087 90 3.543 60 2.362 90 3.543 50 1.969 35 1.378 100 3.937 50 1.969 30 1.181 P.57 FT-Z802Y 320 12.598 160 6.299 120 4.724 160 6.299 80 3.150 60 2.362 320 12.598 160 6.299 120 4.724 P.57 MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide FT-Z30W Notes: 1) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 2) Because infrared types are easily affected by humidity, please ask assistance when using them in a humid environment or in an environment with varying humidity. Fibers Fiber Amplifiers Retroreflective type FX-500 FX-100 FX-300 FX-410 Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. Sensing range (mm in) (Note 1, 2) FX-311 FX-301-F7/ FX-301-F FX-301B / 311B Model No. FR-KZ22E FX-301G / 311G FX-301H Dimensions LONG STD FAST LONG STD FAST LONG STD FAST - - - - - - - - - P.58 FR-KZ50E 20 to 160 0.787 to 6.299 20 to 100 0.787 to 3.937 20 to 60 0.787 to 2.362 20 to 110 0.787 to 4.331 20 to 54 0.787 to 2.126 - 20 to 100 0.787 to 3.937 20 to 33 0.787 to 1.299 - P.58 FR-KZ50H 20 to 140 0.787 to 5.512 20 to 70 0.787 to 2.76 20 to 52 0.787 to 2.047 20 to 90 0.787 to 3.543 20 to 40 0.787 to 1.575 - 20 to 80 0.787 to 3.150 20 to 43 0.787 to 1.693 - P.58 - 100 to 410 3.937 to 16.142 - P.58 FR-Z50HW - - - - - - Notes: 1) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 2) The sensing range is the possible setting range for the attached reflector. The fiber can detect an object less than setting range for the reflector. However, note that if there are any white or highly-reflective surfaces near the fiber head, reflected incident light may affect the fiber head. If this occurs, adjust the threshold value of the amplifier unit before use. Digital Fiber Sensor FX-300 SERIES SENSING RANGE OF BLUE LED / GREEN LED / INFRARED LED 152 FIBER SENSORS Reflective type LASER SENSORS Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. PHOTOELECTRIC SENSORS Sensing range (mm in) (Note 1, 2) / Description FX-301B / 311B Model No. LONG STD FX-301G / 311G FAST LONG STD FX-301H FAST LONG STD Dimensions AREA SENSORS FAST FD-30 19 0.748 9 0.354 6 0.236 9 0.354 4.5 0.177 2.5 0.098 8 0.315 4 0.157 2.5 0.098 P.59 FD-31 18 0.709 8 0.315 5 0.197 8 0.315 4 0.157 2 0.079 7 0.276 3 0.118 2 0.079 P.59 6 0.236 3 0.118 - - FD-31W 7 0.276 FD-32G 22 0.866 11 0.433 8 0.315 15 0.591 6 0.236 4 0.157 11 0.433 6 0.236 2 0.079 P.59 FD-32GX 25 0.984 11 0.433 8 0.315 16 0.630 6 0.236 4 0.157 14 0.551 7 0.276 4 0.157 P.59 FD-40 19 0.748 9 0.354 6 0.236 9 0.354 4.5 0.177 2.5 0.098 8 0.315 4 0.157 2.5 0.098 P.59 FD-41 18 0.709 8 0.315 5 0.197 8 0.315 4 0.157 2 0.079 7 0.276 3 0.118 2 0.079 P.59 FD-41S 18 0.709 8 0.315 5 0.197 8 0.315 4 0.157 2 0.079 7 0.276 3 0.118 2 0.079 P.59 FD-41SW 4 0.157 1 to 2.5 0.039 to 0.098 5 0.197 1 to 2 0.039 to 0.079 9 0.354 1 to 4 0.039 to 0.157 1 to 2.5 0.039 to 0.098 1 to 4 0.039 to 0.157 1 to 2 0.039 to 0.079 - 6 0.236 1 to 3 0.039 to 0.118 - MICRO PHOTOELECTRIC SENSORS P.59 P.59 LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS FD-41W 32 1.260 1 to 15 0.039 to 0.591 1 to 9 0.039 to 0.354 17 0.669 1 to 7.5 0.039 to 0.295 1.5 to 4.5 0.059 to 0.177 18 0.709 1 to 9 0.039 to 0.354 1.5 to 5 0.059 to 0.197 P.59 FD-42G 22 0.866 11 0.433 8 0.315 15 0.591 6 0.236 4 0.157 11 0.433 6 0.236 2 0.079 P.60 FD-42GW 14 0.551 7 0.276 5 0.197 6 0.236 4 0.157 2 0.079 9 0.354 5 0.197 2 0.079 P.60 FD-60 55 2.165 28 1.102 18 0.709 30 1.181 15 0.591 10 0.394 30 1.181 15 0.591 10 0.394 P.60 FD-61 48 1.890 24 0.945 16 0.630 26 1.024 13 0.512 8 0.315 27 1.063 12 0.472 8 0.315 P.60 STATIC ELECTRICITY PREVENTION DEVICES FD-61G 46 1.811 23 0.906 15 0.591 26 1.024 12 0.472 8 0.315 25 0.984 12 0.472 8 0.315 P..60 LASER MARKERS FD-61S 48 1.890 24 0.945 16 0.630 26 1.024 13 0.512 8 0.315 27 1.063 12 0.472 8 0.315 P.60 FD-61W 32 1.260 1 to 15 0.039 to 0.591 1 to 9 0.039 to 0.354 17 0.669 1 to 7.5 0.039 to 0.295 1.5 to 4.5 0.059 to 0.177 18 0.709 1 to 9 0.039 to 0.354 1.5 to 5 0.059 to 0.197 P.60 FD-62 80 3.150 1 to 40 0.039 to 1.575 1 to 27 0.039 to 1.063 1 to 42 0.039 to 1.654 1 to 21 0.039 to 0.827 1 to 14 0.039 to 0.551 54 2.126 1 to 26 0.039 to 1.024 1 to 17 0.039 to 0.669 P.60 FD-64X 32 1.260 0.5 to 16 0.020 to 0.630 0.5 to 10 0.020 to 0.394 0.5 to 16 0.020 to 0.630 0.5 to 8 0.020 to 0.315 0.5 to 5 0.020 to 0.197 27 1.063 22 0.866 P.61 FD-A16 19 0.748 14 0.551 18 0.709 15 0.591 FD-AL11 33 1.299 16 0.630 12 0.472 10 0.394 FD-E13 2 0.079 2 0.079 1 0.039 FD-E23 - - 14 0.551 - FA COMPONENTS 18 0.709 8 0.315 0.8 0.031 0.5 0.020 0.8 0.031 6 0.236 3 0.118 2 0.079 3 0.118 1.5 0.059 1 0.039 8 0.315 4 0.157 2.5 0.098 P.61 FD-EG30 6 0.236 3 0.118 2 0.079 3 0.118 1.5 0.059 1 0.039 8 0.315 4 0.157 2.5 0.098 P.61 FD-EG30S 6 0.236 3 0.118 2 0.079 3 0.118 1 0.039 8 0.315 4 0.157 2.5 0.098 P.62 FD-EG31 2 0.079 1 0.039 0.5 0.020 1 0.039 4 0.157 2 0.079 1 0.039 P.62 FD-F4 FD-F41 FD-F41Y (Note 3) FD-F8Y FD-FA93 FD-H13-FM2 FD-H18-L31 1.5 0.059 - - - - Applicable pipe diameter: Outer dia. o6 to o26 mm o0.236 to o1.024 in transparent pipe [PFA (fluorine resin) or equivalently transparent pipe, wall thickness 1 mm 0.039 in] Liquid absent: Beam received, Liquid present: Beam interrupted Applicable pipe diameter: Outer dia. o6 to o26 mm o0.236 to o1.024 in transparent pipe [PVC (vinyl chloride), fluorine resin, polycarbonate, acrylic, glass, wall thickness 1 to 3 mm 0.039 to 0.118 in] Liquid absent: Beam received, Liquid present: Beam interrupted o4 mm o0.157 in form Protective tube: fluorine resin, length 500 mm 19.685 in (cuttable) Liquid surface not contacted: Beam received, Liquid surface contacted: Beam interrupted - - - - - - - - - 11 0.433 - 7 0.276 - 20 0.787 - 11 0.433 - 7 0.276 - 25 0.984 - 12 0.472 - P.61 P.62 P.62 - UV CURING SYSTEMS 8 0.315 - Selection Guide Fibers Fiber Amplifiers P.62 FX-500 P.62 P.63 P.63 FD-H20-21 36 1.417 18 0.709 12 0.472 20 0.787 10 0.394 7 0.276 140 5.512 70 2.756 45 1.772 P.63 FD-H20-M1 36 1.417 18 0.709 12 0.472 20 0.787 10 0.394 7 0.276 140 5.512 70 2.756 45 1.772 P.63 FD-H25-L43 (Note 4) - - - - - - - - - P.63 FD-H25-L45 (Note 4) - - - - - - - - - P.63 Notes: 1) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 2) The sensing range is specified for white non-glossy paper. (FP-H18-L31 50 x 50 mm 1.969 x 1.969 in. glass substrate). 3) Liquid inflow prevention joint, protective tube extension joint, fiber mounting joint are available. Please refer to p.38 for details. 4) The sensing range is specified for transparent glass 100 x 100 x t0.7 mm 3.937 x 3.937 x t0.028 in MACHINE VISION SYSTEMS P.62 Applicable pipe diameter: Outer dia. o8 mm o0.315 in or more transparent pipe (When used with the tying bands: o8 to o80 mm o0.315 to o3.150 in) [PFA (fluorine resin), including translucent] Liquid absent: Beam received, Liquid present: Beam interrupted 20 0.787 HUMAN MACHINE INTERFACES P.61 10 0.394 - PLC P.61 13 0.512 6 0.236 MEASUREMENT SENSORS ENERGY CONSUMPTION VISUALIZATION COMPONENTS 20 0.787 4.5 0.177 WIRE-SAVING SYSTEMS FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F 153 FIBER SENSORS Digital Fiber Sensor FX-300 SERIES SENSING RANGE OF BLUE LED / GREEN LED / INFRARED LED LASER SENSORS Reflective type PHOTOELECTRIC SENSORS Fibers are listed in alphabetic order. Refer to p.5~ "Fiber Selection" for details of each fiber. MICRO PHOTOELECTRIC SENSORS Sensing range (mm in) (Note 1, 2) / Description LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Fibers Fiber Amplifiers LONG FX-301G / 311G FX-301H Dimensions STD FAST LONG STD FAST LONG STD FAST - - - - - - - - P.64 FD-H30-L32 - - - - - - - - - P.64 FD-H30-L32V-S (Note 3,4) - - - - - - - - - P.64 FD-H30-KZ1V-S (Note 3,4) 30 to 40 1.181 to 1.575 FD-H35-20S 22 0.866 11 0.433 7 0.276 12 0.472 6 0.236 4 0.157 80 3.150 40 1.575 28 1.102 P.64 FD-H35-M2 36 1.417 18 0.709 12 0.472 20 0.787 10 0.394 7 0.276 140 5.512 70 2.756 45 1.772 P.64 FD-H35-M2S6 36 1.417 18 0.709 12 0.472 20 0.787 10 0.394 7 0.276 140 5.512 70 2.756 45 1.772 P.64 o4 mm o0.157 in form Protective tube: fluorine resin, length:500 mm 19.685 in (allowable cutting) FD-HF40Y (Note 5) Liquid surface not contacted: Beam received, Liquid surface contacted: Beam interrupted FD-L10 (Note 6) FD-L11 (Note 6) FD-L12W (Note 6) FD-L20H 0 to 3.5 0 to 0.138 0 to 3 0 to 0.118 0.5 to 2.5 0.020 to 0.098 0 to 3 0 to 0.118 1 to 2 0.039 to 0.079 7 0.276 - 6.5 0.256 0.5 to 5.5 0.020 to 0.217 - - 6.5 0.256 1 to 4 0.039 to 0.157 - - 4.5 to 10 0.177 to 0.394 5 to 9 0.197 to 0.354 5.5 to 8 0.217 to 0.315 5 to 9 0.197 to 0.354 5.5 to 8 0.217 to 0.315 - - P.64 0 to 3 0 to 0.118 1 to 2 0.039 to 0.079 - P.65 6.5 0.256 1 to 4.5 0.039 to 0.177 - P.65 - - - - P.65 - 4.9 to 8.5 0.193 to 0.335 - - P.65 FD-L21 (Note 6) - - - - - - - - - P.65 FD-L21W (Note 6) - - - - - - - - - P.65 FD-L22A (Note 6) - - - - - - - - - P.65 FD-L23 (Note 6) - - - - - - - - - P.65 FD-L30A (Note 6) - - - - - - - - - P.65 FD-L31A (Note 6) - - - - - - - - - P.65 FD-L32H (Note 6) - - - - - - - - - P.66 FD-R31G FD-R32EG 17 0.669 8 0.315 5 0.197 8 0.315 6 0.236 3 0.118 1.5 0.059 2 0.079 FD-R33EG 2 0.079 0.8 0.031 0.5 0.020 1 0.039 FD-R34EG 5 0.197 2 0.079 1.5 0.059 2 0.079 FD-R41 24 0.945 1 to 13 0.039 to 0.512 FD-R60 42 1.654 FD-R61Y 36 1.417 4 0.157 1 0.039 - 1 0.039 2 0.079 - 9 0.354 4 0.157 8 0.315 4 0.157 - 3 0.118 1.5 0.059 - 6 0.236 3 0.118 2 0.079 P.66 2.5 0.098 P.66 - P.66 2 0.079 P.66 14 0.551 1 to 6 0.039 to 0.236 1 to 3 0.039 to 0.118 P.66 20 0.787 0.5 to 13 0.020 to 0.512 21 0.827 0.5 to 10 0.020 to 0.394 0.5 to 7 0.020 to 0.276 27 1.063 8 0.315 P.66 17 0.669 0.5 to 11 0.020 to 0.433 19 0.748 0.5 to 9 0.020 to 0.354 1 to 6 0.039 to 0.236 19 0.748 0.5 to 10 0.020 to 0.394 0.5 to 6 0.020 to 0.236 P.66 1 to 9 0.039 to0.354 1 to 15 0.039 to 0.591 1 to 8 0.039 to 0.315 3 to 6 0.118 to 0.236 12 0.472 FD-S21 8 0.315 3.5 0.138 2 0.079 5 0.197 2 0.079 1.3 0.051 9 0.354 4 0.157 3 0.118 P.66 FD-S30 19 0.749 9 0.354 6 0.236 9 0.354 4.5 0.177 2.5 0.098 8 0.315 4 0.157 2.5 0.098 P.67 FD-S31 18 0.709 8 0.315 5 0.197 8 0.315 4 0.157 2 0.079 7 0.276 3 0.118 2 0.079 P.67 FD-S32 48 1.890 24 0.945 16 0.630 26 1.024 13 0.512 8 0.315 27 1.063 12 0.472 8 0.315 P.67 FD-S32W 32 1.260 1 to 15 0.039 to 0.591 1 to 9 0.039 to 0.354 18 0.709 1 to 9 0.039 to 0.354 1.5 to 5 0.059 to 0.197 P.67 FD-S33GW 14 0.551 FX-500 FD-S60Y FX-100 FD-V30 FX-300 FD-V30W FX-410 FD-V50 FX-311 FD-Z20HBW FX-301-F7/ FX-301-F FX-301B / 311B Model No. AREA SENSORS FD-Z20W 50 1.969 9 0.354 - 7 0.276 5 0.197 20 0.787 3 to 12 0.118 to 0.472 17 0.669 1 to 7.5 0.039 to 0.295 1.5 to 4.5 0.059 to 0.177 6 0.236 4 0.157 28 1.102 3 to 9 0.118 to 0.354 2 0.079 - 2 0.079 P.67 30 1.181 2 to 13 0.079 to 0.512 5 to 6.5 0.197 to 0.256 P.67 9 0.354 5 0.197 - - - - - - - - P.67 - - - - - - P.67 - - - - P.68 - P.68 - P.68 - - 12 0.472 - - 4 to 10 0.157 to 0.394 - - - - - 3 to 11 0.118 to 0.433 4 to 6 0.157 to 0.236 - - - - - - 5 to 8 0.197 to 0.315 6 0.236 6 0.236 - FD-Z40HBW 1 to 36 0.039 to 1.417 3 to 17 1.181 to 0.669 3 to 11 1.181 to 0.433 2 to 19 0.079 to 0.748 3 to 8 0.118 to 0.315 4 to 5 0.157 to 0.197 2 to 20 0.0787 to 0.787 3 to 10 0.118 to 0.394 4 to 5.5 0.157 to 0.217 FD-Z40W 4 to 20 0.157 to 0.787 - - 4 to 14 0.157 to 0.551 - - 5 to 10 0.197 to 0.394 - - P.68 - - - - - - - - - P.68 FD-Z50HW Notes: 1) The standard sensing objects of the sensing ranges vary depending on the fibers. 2) Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) The sensing range of reflective type is the value for white non-glossy paper. 4) Sold as a set comprising vacuum type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8). 5) Liquid inflow prevention joint, protective tube extension joint, fiber mounting joint are available. Please refer to p.38 for details. 6) The sensing range is specified for transparent glass 100 x 100 x t.0.07 mm 3.937 x 3.937 x t0.028 in, (FD-L32H: R-edge, FD-L21 and FD-L21W: t2 mm t0.079 in) [FD-L10: silicon wafers 100 x 100 mm 3.937 x 3.937 in] P.68 Digital Fiber Sensor FIBER OPTIONS 154 FX-300 SERIES Refer to p. 69~ for details of lens dimensions. LASER SENSORS Lens (for thru-beam type fiber) Designation Model No. PHOTOELECTRIC SENSORS Description Sensing range for red LED type (mm) [Lens on both sides] (Note 2) Increases the sensing range by 5 times or more. Expansion lens (Note 1) FX-LE1 * Ambient temperature: -60 to +350 C -76 to +662 F (Note 5) * Beam dia: o3.6 mm o0.142 in Fiber Mode U-LG LONG STDF STD FAST S-D H-SP 2,900 2,100 1,300 1,200 2,800 1,600 1,600 FT-43 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) FT-42 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) FT-45X 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,500 FT-R40 3,600 (Note 3) 3,600 (Note 3) 3,500 3,400 2,700 1,500 1,500 FT-H35-M2 3,500 (Note 3) 3,500 (Note 3) 2,500 2,000 1,500 750 700 1,300 900 500 400 1,100 900 600 FT-H20W-M1 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) FT-H20-M1 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) Sensing range for red LED type (mm) [Lens on both sides] (Note 2) Tremendously increases the sensing range with large diameter lenses. FX-LE2 For thru-beam type fiber Superexpansion lens (Note 1) * Ambient temperature: -60 to +350 C -76 to +662 F (Note 5) * Beam dia: o9.8 mm o0.386 in Beam axis is bent by 90. Side-view lens Expansion lens for vacuum fiber (Note 1) Vacuum resistant side-view lens (Note 1) FX-SV1 FV-LE1 FV-SV2 FIBER SENSORS * Ambient temperature: -60 to +300 C -76 to +572 F (Note 5) * Beam dia: o2.8 mm o0.110 in Fiber Mode U-LG LONG STDF STD FAST S-D H-SP FT-43 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) FT-42 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) FT-45X 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) FT-R40 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) 3,600 (Note 3) FT-H35-M2 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) FT-H20W-M1 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,500 1,600 (Note 3) FT-H20-M1 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) 1,600 (Note 3) FT-H13-FM2 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) 3,500 (Note 3) MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC Sensing range for red LED type (mm) [Lens on both sides] (Note 2) Fiber Mode U-LG LONG STDF STD FAST S-D H-SP FT-43 1,900 1,200 840 580 420 250 240 FT-42 2,100 1,400 870 640 440 210 210 FT-45X 840 650 450 220 220 FT-H35-M2 1,600 (Note 3) 1,600 (Note 3) 840 550 370 280 200 90 90 FT-H20W-M1 400 310 180 140 100 50 50 FT-H20-M1 840 550 370 280 200 90 90 Sensing range increases Sensing range for red LED type (mm) [Lens on both sides] (Note 2, 4) by 4 times or more. Mode U-LG LONG STDF STD FAST S-D H-SP * Ambient temperature: Fiber -60 to +350 C FT-H30-M1V-S 1,600 1,200 650 450 300 150 200 -76 to +662 F (Note 5) * Beam dia: o3.6 mm o0.142 in Beam axis is bent by Sensing range for red LED type (mm) [Lens on both sides] (Note 2, 4) 90. Mode U-LG LONG STDF STD FAST S-D H-SP * Ambient temperature: Fiber -60 to +300 C FT-H30-M1V-S 1,600 1,200 650 450 300 150 200 -76 to +572 F (Note 5) * Beam dia: o3.7 mm o0.146 in Notes: 1) Be careful sure to use it only after you have adjusted it sufficiently when installing the thru-beam type fiber equipped with the expansion lens, as the beam envelope becomes narrow and alignment is difficult. 2) The sensing ranges are the values for red LED type amplifier. Please contact our office for details on sensing ranges for other types of amplifiers. 3) The fiber cable length practically limits the sensing range. 4) The fiber cable length for the FT-H30-M1V-S is 1 m 3.281 ft. The sensing ranges in U-LG and LONG modes take into account the length of the FT-J8 atmospheric side fiber. 5) Refer to p.15, p18, p.33 and p.35 for the ambient temperatures of fibers to be used in combination. HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F 155 Digital Fiber Sensor FIBER OPTIONS FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS FX-300 SERIES Refer to p. 69~ for details of lens dimensions. Lens (for reflective type fiber) Designation MICRO PHOTOELECTRIC SENSORS Model No. Pinpoint spot of o0.5 mm o0.020 in. Enables detection of minute objects or small marks. Pinpoint spot lens AREA SENSORS Description FX-MR1 LIGHT CURTAINS / SAFETY COMPONENTS * Distance to focal point: 6 1 mm 0.236 0.039 in * Applicable fibers: FD-42G, FD-42GW * Ambient temperature: -40 to +70 C -40 to +158 F (Note) The spot diameter is adjustable from o0.7 to o2 Sensing range for red LED type (Note 1) mm o0.028 to o0.079 in according to how much Screw-in depth Distance to focal point Spot diameter the fiber is screwed in. * Applicable fibers: FD-42G, FD-42GW 7 mm 18.5 mm approx. o0.7 mm * Ambient temperature:-40 to +70 C 27 mm approx. o1.2 mm 12 mm -40 to +158 F (Note 2) Spot * Accessory: M S-EX3 (mounting bracket) 43 mm approx. o2.0 mm 14 mm diameter Screw-in depth PRESSURE / FLOW SENSORS FX-MR2 Zoom lens Distance to focal point INDUCTIVE PROXIMITY SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS For reflective type fiber PARTICULAR USE SENSORS Finest spot lens FX-MR3 Distance to focal point Spot diameter STATIC ELECTRICITY PREVENTION DEVICES Finest spot lens FX-MR6 LASER MARKERS PLC side-view type Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 Sensing range for red LED type (Note 1) FX-MR5 Distance to focal point Spot diameter FD-EG31 7.5 0.5 mm o0.15 mm approx. FD-EG30 7.5 0.5 mm o0.3 mm approx. FD-42G/42GW 7.5 0.5 mm o0.5 mm approx. FD-32G/32GX Fiber model No. Distance to focal point Spot diameter FD-EG31 7 0.5 mm o0.1 mm approx. FD-EG30 7 0.5 mm o0.2 mm approx. FD-42G/42GW FD-32G/32GX 7 0.5 mm o0.4 mm approx. Sensing range for red LED type (Note 1) Screw-in depth Distance to focal point Spot diameter 8 mm 13 mm approx. o0.5 mm 10 mm 15 mm approx. o0.8 mm 14 mm 30 mm approx. o3.0 mm Lens (For square head M3 reflective fiber) Spot diameter (mm in) (Note) Type Distance to focal point (mm in) (Note) Lens Shape Model No. (mm in) Shape o0.1 o0.004 approx. o0.15 o0.006 approx. Finest spot lens o0.2 o0.008 approx. 7 0.5 0.276 0.020 o5 o0.197 15.3 0.602 FX-MR7 o0.4 o0.016 approx. FX-410 FX-311 Parallel light lens Zoom lens Type For Square head M3 reflective fiber FX-301-F7/ FX-301-F Fiber model No. Distance to focal point Spot diameter Notes: 1) The sensing ranges are the values when used in combination with a red LED type amplifier. Please contact our office for details on sensing ranges for other types of amplifier. 2) Refer to p.16 or p.26 for the ambient temperatures of fibers to be used in combination. For Square head M3 reflective fiber UV CURING SYSTEMS Extremely fine spot of o0.1 mm o0.004 in approx. achieved. * Applicable fibers: FD-EG31, FD-EG30, FD-42G, FD-42GW, FD-32G, FD-32GX * Ambient temperature: -20 to +60 C -4 to +140 F (Note 2) can be mounted in a very small space. * Applicable fibers: FD-42G, FD-42GW * Ambient temperature: -40 to +70 C -40 to +158 F (Note 2) Zoom lens ENERGY CONSUMPTION VISUALIZATION COMPONENTS MACHINE VISION SYSTEMS Sensing range for red LED type (Note 1) Screw-in FX-MR2 is converted into a side-view type and depth HUMAN MACHINE INTERFACES FA COMPONENTS Extremely fine spot of o0.15 mm o0.006 in approx. achieved. * Applicable fibers: FD-EG31, FD-EG30, FD-42G, FD-42GW, FD-32G, FD-32GX * Ambient temperature: -40 to +70 C -40 to +158 F (Note 2) Spot diameter (mm in) (Note) Sensing range (mm in) (Note) Lens Shape fiber Model No. Emitting (mm in) core (mm in) o0.4 to o2.0 o0.016 to o0.079 approx. o0.4 to o2.2 o0.016 to o0.087 approx. 10 to 30 o5 o0.197 o0.5 to o2.5 o0.020 to o0.098 approx. 0.394 to1.181 15 0.591 FX-MR8 o0.8 to o3.5 o0.031 to o0.138 approx. o4.0 o0.157 approx. 0 to 30 0 to 1.181 10 0.394 o5 o0.197 FX-MR9 Fiber Emitting fiber core (mm in) Model No. o0.125 o0.005 FD-R33EG o0.125 o0.005 FD-EG31 o0.175 o0.007 FD-R34EG o0.25 o0.010 FD-R32EG o0.25 o0.010 FD-EG30 o0.5 o0.020 FD-R31G o0.5 o0.020 FD-32G o0.5 o0.020 FD-32GX o0.5 o0.020 FD-42G o0.5 o0.020 FD-42GW Applicable fibers Model No. o0.125 o0.005 FD-R33EG, FD-EG31 o0.175 o0.007 FD-R34EG o0.25 o0.010 FD-R32EG, FD-EG30 o0.5 o0.020 FD-R31G, FD-32G, FD-32GX, FD-42G, FD-42GW o0.125 o0.005 FD-R33EG, FD-EG31 o0.175 o0.007 FD-R34EG o0.25 o0.010 FD-R32EG, FD-EG30 o0.5 o0.020 FD-R31G, FD-32G, FD-32GX, FD-42G, FD-42GW Note: Spot diameter, distance to focal point and sensing range are specified for a red LED type amplifier. Digital Fiber Sensor FIBER OPTIONS Model No. FTP-500 (0.5 m 1.640 ft) FTP-1500 (1.5 m 4.921 ft) FTP-N500 (0.5 m 1.640 ft) For M3 thread FTP-N1000 (1 m 3.281 ft) Applicable fibers Protective tube for thru-beam type fiber FT-42 FT-42S FT-42W For M4 thread FTP-1000 (1 m 3.281 ft) FTP-N1500 (1.5 m 4.921 ft) FDP-500 (0.5 m 1.640 ft) For M6 thread FDP-1000 (1 m 3.281 ft) Protective tube for reflective type fiber FDP-1500 (1.5 m 4.921 ft) FDP-N500 (0.5 m 1.640 ft) FDP-N1500 (1.5 m 4.921 ft) AREA SENSORS Fiber bender FT-31 FT-31S FT-31W FD-31 FD-31W FD-61 FD-61G FD-61S FD-61W Using the arm which enables adjustment in the horizontal direction, sensing can also be done from above an assembly line. FD-41S FD-41SW * MS-AJ1-F MS-AJ1-F Horizontal mounting type MS-AJ2-F Vertical mounting type Fiber mounting joint (Note 2) MS-FX-03Y Single core holder Applicable fibers Universal sensor mounting stand (Note 2) MS-FX-02Y The protective tube can be extended. The joint is used for mounting fibers on a tank. The incident light intensity may vary when using a multi-core fiber or a thin type sharp bending fiber. This holder suppresses the variation in the incident light intensity. (Brown) FX-AT15A RF-210 Used with FR-Z50HW. Refer to p.30 or p.41 for the sensing range of FR-Z50HW to be used in combination. RF-220 Reflector Mounting stand assembly for fiber (For M3, M4 or M6 threaded head fiber) This joint suppresses false operations due to liquid slip-in from the top of the protective tube. FD-HF40Y FD-F41Y RF-230 Notes: 1) Do not bend the sleeve part of any side-view type fiber or ultra-small diameter head type fiber. 2) The joint internal ferrule (MS-FX-YF) is available as a spare part. A distorted ferrule may result in leakage. Liquid inflow prevention joint MS-FX-01Y * MS-FX-01Y MS-FX-01Y MS-FX-01Y Ferrule (MS-FX-YF) Union nut Protective tube extension joint MS-FX-02Y * MS-FX-02Y MS-FX-02Y MS-FX-02Y Union nut Body Ferrule (MS-FX-YF) Body Body Union nut Ferrule (MS-FX-YF) * RF-210 33.3 mm 1.311 in 11 mm 0.433 in MS-FX-03Y * MS-FX-03Y MS-FX-03Y MS-FX-03Y Body Ferrule (MS-FX-YF) Body Body Union nut Ferrule (MS-FX-YF) Union nut * RF-220 35.3 mm 1.390 in Ferrule (MS-FX-YF) Union nut 8.3 mm 0.327 in * RF-230 50.3 mm 1.980 in 12.8mm 0.504 in 42.3 mm 1.665 in 59.3 mm 2.335 in 360 rotation Forward / back adjustment: 130 mm 5.118 in approx. 360 rotation 20 20 Angle adjustment: 20 Forward / back adjustment: 130 mm 5.118 in approx. 360 rotation Height adjustment: 150 mm 5.906 in approx. 20 20 Angle adjustment: 20 PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC 360 rotation Mounting hole for M6 screw HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Single core holder * FX-AT15A Selection Guide Fibers Fiber Amplifiers Union nut Ferrule (MS-FX-YF) Union nut Union nut Ferrule (MS-FX-YF) Body Ferrule (MS-FX-YF) Body Height adjustment: 150 mm 5.906 in approx. Mounting hole for M6 screw * MS-AJ2-F Fiber mounting joint Ferrule (MS-FX-YF) Union nut Union nut Ferrule (MS-FX-YF) Ferrule (MS-FX-YF) Body Reflector INDUCTIVE PROXIMITY SENSORS Universal sensor mounting stand FB-1 Protective tube extension joint (Note 2) PRESSURE / FLOW SENSORS The protective tube, made of noncorrosive stainless steel, protects the FD-62 inner fiber cable from FD-H13-FM2 any external forces. Fiber bender MS-FX-01Y LIGHT CURTAINS / SAFETY COMPONENTS * FB-1 The fiber bender bends the sleeve part of the fiber head at the proper radius. (Note 1) Liquid inflow prevention joint (Note 2) MICRO PHOTOELECTRIC SENSORS FT-43 FT-H13-FM2 FD-41 FD-41W For M4 thread FDP-N1000 (1 m 3.281 ft) PHOTOELECTRIC SENSORS * FTP- * FDP- Description FIBER SENSORS LASER SENSORS Protective tube Designation 156 Refer to p. 69~ for details of lens dimensions. Others Union nut FX-300 SERIES FX-500 FX-100 FX-300 FX-410 FX-311 8.3 mm 0.327 in FX-301-F7/ FX-301-F 157 Digital Fiber Sensor SPECIFICATIONS FIBER SENSORS LASER SENSORS Type AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS Model No. PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS FX-300 SERIES Item PARTICULAR USE SENSORS FX-301 FX-301B FX-301G FX-301H FX-301-HS FX-305 FX-301BP FX-301GP FX-301HP FX-301P-HS FX-305P Power consumption Output PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F <NPN output type> <NPN output type> NPN open-collector transistor NPN open-collector transistor 2 outputs * Maximum sink current:100 mA (50 mA, if five, or more, amplifiers are connected in cascade.) * Maximum sink current: 50 mA each (Note 2) * Applied voltage: 30 V DC or less (between output and 0 V) * Applied voltage: 30 V DC or less (between output and 0 V) * Residual voltage: 1.5 V or less [at 100 mA (at 50 mA, if five, or more, amplifiers are connected in cascade) sink current.] * Residual voltage: 1.5 V or less [at 50 mA (Note 2)] <PNP output type> <PNP output type> PNP open-collector transistor 2 outputs PNP open-collector transistor * Maximum source current: 50 mA each (Note 2) * Maximum source current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade.) * Applied voltage: 30 V DC or less (between output and +V) * Applied voltage: 30 V DC or less (between output and +V) * Residual voltage: 1.5 V or less [at 50 mA (Note 2)] * Residual voltage: 1.5 V or less [at 100 mA (at 50 mA, if five, or more, amplifiers are connected in cascade) source current.] Selectable either Light-ON or Dark-ON, with jog switch Short-circuit protection Response time Sensitivity setting Incorporated 35 s or less (H-SP), 65 s or less [H-SP (Red LED type only)], 150 s or less (FAST), 150 s or less (FAST), 250 s or less [STD / S-D (Red LED type only)], 250 s or less (STD / S-D), 2 ms or less (LONG), selectable with jog switch 2 ms or less (LONG), selectable with jog switch Stability indicator Orange LED (lights up when the output is ON) - Green LED (lights up under stable light received condition or stable dark condition) MODE indicator RUN: Green LED, TEACH * ADJ * L/D ON * TIMER * PRO: Yellow LED Digital display 4 digit red LED display Fine sensitivity adjustment function Timer function 65 s or less (H-SP), 150 s or less (FAST), 250 s or less (STD), 700 s or less (STDF), 2.5 ms or less (LONG), 4.5 ms or less (U-LG), selectable with jog switch Normal mode: 2-point teaching / Limit teaching / Full-auto teaching / Max. sensitivity teaching / Manual adjustment Window comparator mode: Teaching (1-point / 2-point / 3-point) / Manual adjustment 2-point teaching / Limit teaching / Manual adjustment / Full-auto teaching / Max. sensitivity teaching Operation indicator Incorporated Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. Timer period: Red LED type; 0.5 ms approx., 1 to 9,999 ms (Blue LED, Green LED, Infrared LED type; approx. 0.5 to 500 ms) Incorporated with variable ON-delay / OFF-delay / ONE SHOT / ON-delay * OFF-delay / ON-delay * ONE SHOT timer, switchable either effective or ineffective. (Timer period: Output 1; 0.5 ms, 1 to 9,999 ms, Output 2; 0.5 ms, 1 to 500 ms) Light emitting amount selection function Incorporated (Red LED type only) (Note 3) FAST, STD, LONG: 4 level, H-SP: 3 level, S-D: 2 level Incorporated (Note 3) FAST, STD, LONG: 4 level H-SP, S-D: 2 level Incorporated (Note 3) FAST, STD, STDF, LONG, U-LG: 4 level H-SP: 3 level Automatic interference prevention function Incorporated (Up to four sets of fiber heads can be mounted close together. However, 2 fiber heads in H-SP mode.) (Note 4) - Incorporated [Up to four sets of fiber heads can be mounted close together. (However, 8 fiber heads in U-LG mode, 2 fiber heads in H-SP mode.)] (Note 5) Environmental resistance LASER MARKERS 12 to 24 V DC 10 % Ripple P-P 10 % or less <Red LED / Infrared LED type> <Blue LED / Green LED type> Normal operation: 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) ECO mode: 430 mW or less (Current consumption 18 mA or less at 24 V supply voltage) Output operation WIRE-SAVING SYSTEMS STATIC ELECTRICITY PREVENTION DEVICES High-function type FX-301P Supply voltage SIMPLE WIRE-SAVING UNITS High-speed Green LED Infrared LED type PNP output SENSOR OPTIONS MEASUREMENT SENSORS Blue LED NPN output PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Standard type Red LED Ambient temperature -10 to +55 C +14 to +131 F (If 4 to 7 units are connected in cascade: -10 to +50 C +14 to +122 F, if 8 to 16 units are connected in cascade: -10 to +45 C +14 to +113 F) (No dew condensation or icing allowed), Storage: -20 to +70 C - 4 to +158 F Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH Ambient illuminance Incandescent light: 3,000 x at the light-receiving face Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 6) Insulation resistance 20 M, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 6) Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each Shock resistance Emitting element (modulated) 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each Red LED Blue LED Green LED Infrared LED Red LED Red LED Peak emission wavelength 650 nm 0.026 mil 470 nm 0.019 mil 525 nm 0.021 mil 940 nm 0.037 mil 650 nm 0.026 mil Material Enclosure: Heat-resistant ABS, Case cover: Polycarbonate, MODE key: Acrylic, Jog switch: Heat-resistant ABS (FX-301B/G/H: Acrylic) Connecting method Cable length Connector (Note 7) Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. Weight Accessory 650 nm 0.026 mil Net weight: 20 g approx., Gross weight: 25 g approx. FX-MB1 (amplifier protection seal): 1 set - FX-MB1 (amplifier protection seal): 1 set Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 C +73.4 F. 2) 50 mA per output. 25 mA if five, or more, amplifiers are connected in cascade. 3) The light emitting amount can be zero (emission halt) in all modes. 4) When the power supply is switched on, the light emission timing is automatically set for interference prevention. 5)When the interference prevention function " " is set, the number of mountable fiber heads becomes double. Furthermore, take care that the response time also becomes double. 6) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only. 7)The cable for amplifier connection is not supplied as an accessory. Make sure to use the optional quick-connection cables given below. Main cable (3-core) for FX-301(P)(-HS): CN-73-C1 (Cable length 1 m 3.281 ft), CN-73-C2 (Cable length 2 m 6.562 ft), CN-73-C5 (Cable length 5 m 16.404 ft) Sub cable (1-core) for FX-301(P)(-HS): CN-71-C1 (Cable length 1 m 3.281 ft), CN-71-C2 (Cable length 2 m 6.562 ft), CN-71-C5 (Cable length 5 m 16.404 ft) Main cable (4-core) for FX-305(P): CN-74-C1 (Cable length 1 m 3.281 ft), CN-74-C2 (Cable length 2 m 6.562 ft), CN-74-C5 (Cable length 5 m 16.404 ft) Sub cable (2-core) for FX-305(P): CN-72-C1 (Cable length 1 m 3.281 ft), CN-72-C2 (Cable length 2 m 6.562 ft), CN-72-C5 (Cable length 5 m 16.404 ft) Digital Fiber Sensor FX-300 SERIES I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS FX-301(-HS) NPN output type I/O circuit diagram Sensor circuit D 1 3 Tr Terminal No. Brown (Note) (Brown) +V (Note 1) (Black) Output Load + 100 mA max. (Note 2) ZD 2 Load Black 12 to 24 V DC 10 % + Note: T he quick-connection sub cable does not have brown lead wire and blue lead wire. Users' circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. 2) 50 mA max., if five amplifiers, or more, are connected together. Terminal arrangement diagram Symbols ... D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : NPN output transistor I/O circuit diagram Sensor circuit 1 ZD Tr 100 mA max. (Note 2) 3 D 2 + (Black) Output Load (Blue) 0 V (Note 1) Internal circuit Users' circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. 2) 50 mA max., if five amplifiers, or more, are connected together. 2 0V SENSOR OPTIONS Color code of quick-connection cable + 12 to 24 V DC 10 % D 1 Tr1 3 Terminal arrangement diagram PLC 1 +V 3 Output 2 0V HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS Tr2 ZD1 4 ZD2 2 Load + (White) Output 2 50 mA max. (Note 2) Black 12 to 24 V DC 10 % Load Load FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS + White 50 mA max. (Note 2) 12 to 24 V DC 10 % Blue (Note) (Blue) 0 V (Note 1) Internal circuit Color code of quick-connection cable Wiring diagram Brown (Note) Load STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS (Brown) +V (Note 1) (Black) Output MEASUREMENT SENSORS Note: T he quick-connection sub cable does not have brown lead wire and blue lead wire. NPN output type Terminal No. SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS FX-305 Color code of quick-connection cable PRESSURE / FLOW SENSORS PARTICULAR USE SENSORS Load Blue (Note) Symbols ... D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor I/O circuit diagram LIGHT CURTAINS / SAFETY COMPONENTS Output Black 12 to 24 V DC 10 % AREA SENSORS INDUCTIVE PROXIMITY SENSORS Brown (Note) (Brown) +V (Note 1) MICRO PHOTOELECTRIC SENSORS 3 Wiring diagram Color code of quick-connection cable PHOTOELECTRIC SENSORS +V PNP output type Terminal No. LASER SENSORS 1 FX-301P(-HS) Sensor circuit 12 to 24 V DC 10 % Blue (Note) (Blue) 0 V (Note 1) Internal circuit Color code of quick-connection cable Wiring diagram Color code of quick-connection cable 158 Note: T he quick-connection sub cable does not have brown lead wire and blue lead wire. Users' circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. 2) 25 mA max., if five amplifiers, or more, are connected together. Terminal arrangement diagram Symbols ... D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr1, Tr2 : NPN output transistor Selection Guide Fibers Fiber Amplifiers 1 +V 3 Output 1 2 0V 4 Output 2 FX-500 FX-100 FX-305P PNP output type Sensor circuit I/O circuit diagram ZD1 1 Terminal No. 50 mA max. (Note 2) Tr2 D Internal circuit 2 (White) Output 2 Load Load Black + 12 to 24 V DC 10 % (Blue) 0 V (Note 1) Users' circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. 2) 25 mA max., if five amplifiers, or more, are connected together. Symbols ... D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr1, Tr2 : PNP output transistor + White Load 12 to 24 V DC 10 % Load Blue (Note) Note: T he quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arrangement diagram 1 +V 3 Output 1 2 0V FX-300 FX-410 FX-311 Brown (Note) (Brown) +V (Note 1) ZD2 (Black) Output 1 50 mA max. (Note 2) 4 Wiring diagram Color code of quick-connection cable 3 Tr1 Color code of quick-connection cable 4 Output 2 FX-301-F7/ FX-301-F 159 FIBER SENSORS Digital Fiber Sensor PRECAUTIONS FOR PROPER USE LASER SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F Refer to p.1458~ for general precautions and to the "PRO mode operation guide" on our website for details pertaining to operating instructions for the amplifier. * Never use this product as a sensing device for personnel protection. * In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. PHOTOELECTRIC SENSORS LIGHT CURTAINS / SAFETY COMPONENTS FX-300 SERIES * The digital fiber sensor FX-301(P) has been modified since its production in June 2004. The explanations below are about the modified product. Mounting 35 mm 1.378 in width DIN rail How to remove the amplifier Push the amplifier forward. Lift up the front part of the amplifier to remove it. Note: Take care that if the front part is lifted without pushing the amplifier forward, the hook on the rear portion of the mounting section is likely to break. Fiber installation * Insert the fiber into the amplifier after attaching the attachment. Refer to the "Instruction Manual" included with the fiber for details. Fiber lock lever Fiber Notes: 1) N ote that if the fiber is not fully inserted, the sensing distance will decrease. Also note that the flexible fiber may bend during insertion. 2) I n case of coaxial reflective type fibers (FD-G4, FD-FM2, etc.), mount the central fiber (single-core) to the emitter part and the peripheral fiber (multi-core) to the receiver. Note that sensing precision will deteriorate when done in reverse. Connection * Make sure that the power supply is off while connecting or disconnecting the quick-connection cable. Connection method H olding the connector of the quick-connection cable, align its projection with the groove at the top portion of the amplifier connector. Insert the connector till a click is felt. Projection Note: Take care that if the connector is pulled out without pressing the projection, the projection may break. Do not use a quick-connection cable whose projection has broken. Further, do not pull by holding the cable, as this can cause a cable-break. Cascading How to mount the amplifier F it the rear part of the mounting section of the amplifier on a 35 mm 1.378 in width DIN rail. P ress down the rear part of the mounting section of the unit on the 35 mm 1.378 in width DIN rail and fit the front part of the mounting section to the 35 mm 1.378 in width DIN rail. P ush the fiber lock lever down. S lowly insert the fiber into the insertion slot until it stops. (Note 1) P ush the fiber lock lever back up until it stops. Disconnection method P ressing the projection at the top of the quick-connection cable, pull out the connector. Groove Projection Quick-connection cable * Make sure that the power supply is off while adding or removing the amplifiers. * Make sure to check the allowable ambient temperature, as it depends on the number of amplifiers connected in cascade. * In case two, or more, amplifiers are connected in cascade, make sure to mount them on a DIN rail. * When the amplifiers move on the DIN rail depending on the attaching condition or the amplifiers are mounted close to each other in cascade, fit them between the optional end plates (MS-DIN-E) mounted at the two ends. * Up to maximum 15 amplifiers can be added (total 16 amplifiers connected in cascade.) * When connecting more than two amplifiers in cascade, use the sub cable (CN-71-C / CN-72-C) as the quick-connection cable for the second amplifier onwards. * When connecting amplifiers not close to each other in parallel, be sure to mount the optional end plate (MS-DIN-E) at both sides of each amplifier or affix the communication window seal of the accessory amplifier protection seal (FX-MB1) to the communication windows. * The settings other than the interference prevention function cannot be transmitted between FX-301(P) FX-301B/G/H(P), FX-305(P). Therefore, in case both models of amplifiers are mounted in cascade, be sure to mount identical models together. However, the interference prevention function is not incorporated in the FX-301(P)-HS. Take care when the sensors are mounted in cascade. * If the FX-301(P) updated version unit or the FX-305(P) is mounted with the FX-301(P) previous version unit or the FX-301B/G/H(P) in cascade, place the FX-301(P) updated version units and the FX-305(P) units to the right side (seen from the connector side) of the previous version units. For details, refer to "Cautions on sensor connection in cascade". For a difference between the updated version unit and the previous version unit, refer to "A difference between the updated version unit and the previous version unit". * The communication function of this product and that of the FX-301(P)-F / F7 is different. If these models are mounted in cascade, affix the accessory fiber amplifier protection seal (FX-MB1) included in the FX-301(P) and FX-305(P) to the communication windows of the amplifiers. Digital Fiber Sensor 35 mm 1.378 in width DIN rail Main unit Sub unit Sub cable (CN-71/72-C) (Optional) How to change the communication specification of Group B * Change the communication specification of Group B according to the following procedures. Make sure to set the communication specification to " (Group A communication specification)" or " (Optical Communication Stop)". <Changing Procedure> End plate (MS-DIN-E) (Optional) ong press the [Jog Switch] and L [MODE key] at the same time. (Note 3) Group B's Communication Specification Group A's Communication Specification * When the units in the group A and the group B shown in the table below are connected in cascade, connect them in cascade as <Figure A> shown below. Group A FX-301(P): Previous version unit (Note 1), FX-301G(P)/B(P)/H(P), FX-41(P), LS-401(P) (Note 2) Group B FX-301(P): Updated version unit (Note 1), FX-305(P) Notes: 1) For the difference between the updated version unit and the previous version unit, refer to "A difference between the updated version unit and the previous version unit". 2) W hen LS-401(P) is connected with the digital fiber amplifier in cascade, be sure to locate LS-401(P) at the left-most position (when viewed from the connector side). * When the units of the group A and the group B are connected in cascade as <Figure B> shown above, optical communications cannot be done. When the optical communications function is used, connect them as <Figure A> shown above. If the units cannot be placed as <Figure A>, the following measure 1 or 2 should be taken. 1 2 Optical Communication Stop Notes: 3) E very time the [Jog Switch] and the [MODE key] is simultaneously long pressed, the display changes in this sequence: " "" "" "" "" ". Cautions on sensor connection in cascade Group A Group B Group B Group A PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS LIGHT CURTAINS / SAFETY COMPONENTS Slide W hen you release the [Jog Switch] and [MODE key], the communication specification will be set and "PRO4" will be displayed. Slide <Figure A> <Figure B> LASER SENSORS AREA SENSORS Display [PRO4]. Main cable (CN-73/74-C) (Optional) FIBER SENSORS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS Dismantling Loosen the screws of the end plates. Remove the end plates. Slide the amplifiers and remove them one by one. Optical communications Optical communications are possible are impossible 160 Refer to p.1458~ for general precautions and to the "PRO mode operation guide" on our website for details pertaining to operating instructions for the amplifier. PRECAUTIONS FOR PROPER USE Cascading method Mount the amplifiers, one by one, on the 35 mm 1.378 in width DIN rail. Slide the amplifiers next to each other, and connect the quickconnection cables. Mount the optional end plates (MS-DIN-E) at both the ends to hold the amplifiers between their flat sides. Tighten the screws to fix the end plates. FX-300 SERIES ffix the communication window seal of the accessory A fiber amplifier protection seal (FX-MB1) to the communication window of the FX-301(P) updated version unit or FX-305(P). If the measure 1 described above cannot be taken, change the optical communications spec. of the group B units. Notes: 4) When the communication specification is set to " (Group A communication specification)", make sure to tightly attach the products. Also make sure to take note of the following: *T here are instances when the optical communication function cannot be used due to the usage environment, etc. *D o not perform batch channel loading or saving. Part description MODE indicator / L/D ON (Yellow) MODE indicator / TIMER (Yellow) Stability indicator (Green)(Note2) Operation indicator (Orange) (Note1) MODE indicator / RUN (Green) MODE indicator / PRO (Yellow) MODE indicator / TEACH (Yellow) MODE indicator / ADJ (Yellow) MODE key SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Jog switch Digital display (Red) Notes: 1 ) FX-305(P); Output 1 operation indicator (Orange) 2) FX-305(P); Output 2 operation indicator (Orange) Operation procedure Selection Guide * When the power supply is switched on, communication self-check is carried out and normal condition is displayed [MODE indicator / RUN (green)] lights up and the digital display shows the incident light intensity. * When the MODE key is pressed, the mode will change as shown in the following diagram. Power ON Press MODE key Press MODE key [Teaching] TEACH (P.161) Press MODE key [Threshold value fine adjust] (P.162) ADJ Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 Communication self-check RUN Fibers FX-311 PRO [PRO mode] Press MODE key TIMER [Timer operation setting] (P.162) Press MODE key Press MODE key L/D [Output operation setting] (P.162) When Jog switch is pressed, the setting is confirmed. When MODE key is pressed for 2 sec., or more, the sensor returns to the `RUN' mode. Cancellation is possible by pressing MODE key during setting. FX-301-F7/ FX-301-F 161 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Digital Fiber Sensor PRECAUTIONS FOR PROPER USE Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F Refer to p.1458~ for general precautions and to the "PRO mode operation guide" on our website for details pertaining to operating instructions for the amplifier. For FX-305(P) The FX-305(P) is equipped with two independent outputs, but the items that can be set in output 1 and output 2 respectively are only the following. The items other than those are common. 1 Threshold value 2 Output operation 3 Timer operation and Timer period 4 Sensing mode Teaching * The threshold values can be set by 2-point teaching, limit teaching, full-auto teaching or window comparator mode (1-point, 2-point, 3-point teaching) [only for FX-305(P)], when the MODE indicator / TEACH (yellow) lights up. In case of 2-point teaching * This is the method of setting the threshold value by teaching two levels, corresponding to the object present and object absent conditions. Normally, setting is done by this method. Step Description Display Set the fiber within the sensing range. Press MODE key to light up MODE indicator / TEACH (yellow). For FX-305(P), select either Output 1 " " or Output 2 " " beforehand, press jog switch in the object present condition. If the teaching is accepted, the read incident light intensity blinks in the digital display. Thru-beam type Reflective type Mark Beam blocked condition Background MODE indicator / TEACH (yellow) blinks. Press jog switch in the object absent condition. Thru-beam type Reflective type Mark Beam incident condition Selection Guide FX-300 SERIES Background If the teaching is accepted, the read incident light intensity blinks in the digital display and the threshold value is set at the midvalue between the incident light intensities in the object present and the object absent conditions. After this, the judgment on the stability of sensing is displayed. * In case stable sensing is possible: " " is displayed. * In case stable sensing is not possible: " " blinks. The threshold value is displayed. " " blinks in the digital display. (only FX-301B/G/H) The incident light intensity appears in the digital display and the setting is complete. Notes: 1) Do not move or bend the fiber cable after the sensitivity setting. Detection may become unstable. 2) In case a reflective-type fiber is used, maximum sensitivity will be set if the jog switch is pushed while in no work status in procedure and . In case of full auto-teaching * Full auto-teaching is used when it is desired to set the threshold value without stopping the assembly line, with the object in the moving condition. Step Description Display Set the fiber within the sensing range. Press MODE key to light up MODE indicator / TEACH (yellow). For FX-305(P), select either Output 1 " " or Output 2 " " beforehand, press the jog switch continuously for 0.5 sec. or more with the object moving on the assembly line. (The incident light intensity is displayed during sampling.) " " is displayed on the digital display. Release the jog switch when the object has passed. If the teaching is accepted, the read incident light intensity blinks in the digital display and the threshold value is set at the midvalue between the incident light intensities in the object present and the object absent conditions. After this, the judgment on the stability of sensing is displayed. * In case stable sensing is possible: " " is displayed. * In case stable sensing is not possible: " " blinks. The threshold value is displayed. " " blinks in the digital display. (only FX-301B/G/H) The incident light intensity appears in the digital display and the setting is complete. Notes: 1) The threshold value's shift amount can be selected in PRO mode. Refer to the "PRO Mode Operation Guide" for more details pertaining to setting instructions. (Increments of 5 % between -45 and 45 % for setting possible. 0 % default.) 2) D o not move or bend the fiber cable after the sensitivity setting. Detection may become unstable. Digital Fiber Sensor PRECAUTIONS FOR PROPER USE Description Step For FX-305(P), select either Output 1 " " or Output 2 " " beforehand, in case the threshold value is to be increased (sensitivity to be reduced), turn the jog switch to the "+" side to increase the threshold value slowly. If the jog switch is turned continuously to the "+" side, the threshold value increases rapidly. In case the threshold value is to be decreased (sensitivity to be increased), turn the jog switch to the "-" side to decrease the threshold value slowly. If the jog switch is turned continuously to the "-" side, the threshold value decreases rapidly. When jog switch is pressed, the threshold value is confirmed. Background body Beam incident condition MODE indicator / TEACH (yellow) blinks. Turn jog switch to the "+" side or "-" side. Threshold value 100 % Low 0 15 % Threshold value Incident light intensity with object absent 15 % ON OFF - Threshold value Turn to "+" side Turn to "-" side After this, the judgment on whether the setting shift amount can be shifted or not is displayed. * I n case shifting is possible: " " blinks. * I n case shifting is not possible: " " blinks. The threshold value is displayed. " " blinks in the digital display. (only FX-301B/G/H) The incident light intensity appears in the digital display and the setting is complete. Notes: 1) Scrolling display is not available in FX-301B/G/H. 2) The approx. 15 % amount of shift is the initial value. The amount of shift can be changed in the PRO mode from approx. 5 to 80 % (5 % step). Refer to the "PRO Mode Operation Guide" for more details pertaining to setting instructions. 3) Do not move or bend the fiber cable after the sensitivity setting. Detection may become unstable. Please download the instruction manual from our website for setting of threshold value when used in combination with liquid level sensing fiber FD-F8Y and with pipe-mountable liquid level sensing fiber FD-F4. For the wind comparator mode teaching in FX-305(P), refer to the separately prepared "PRO Mode Operation Guide". PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS Thru-beam type Reflective type ON Display Press MODE key to light up MODE indicator / ADJ (yellow). For FX-305(P), select either Output 1 " " or Output 2 " " beforehand, press jog switch in the object absent condition. If the teaching is accepted, the read incident light intensity blinks in the display. OFF Description Display If jog switch is turned to the "+" side, " " scrolls (twice) the display from right to left (Note 1), and the threshold level is shifted to a value approx. 15 % higher (lower sensitivity) than that set at . (Note 2) This is used in case of reflective type fibers. If jog switch is turned to the "-" side, " " scrolls (twice) the display from left to right, and the threshold level is shifted to a value approx. 15 % lower (higher sensitivity) than that set at . (Note 2) This is used in case of thru-beam type fibers. FIBER SENSORS LASER SENSORS Threshold value fine adjustment Set the fiber within the sensing range. Press MODE key to light up MODE indicator / TEACH (yellow). High 162 Refer to p.1458~ for general precautions and to the "PRO mode operation guide" on our website for details pertaining to operating instructions for the amplifier. In case of limit teaching * This is the method of setting the threshold value by teaching only the object absent condition (stable incident light condition). This is used for detection in the presence of a background body or for detection of small objects. Step FX-300 SERIES LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS or PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS - MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS Output operation setting Step Description Press MODE key to light up MODE indicator / L/D ON (yellow). For FX-305(P), select either Output 1 " or Output 2 " " beforehand, if the jog switch is turn to the "+" or "-" direction, the output operation setting will change. When jog switch is pressed, the threshold value is confirmed. Display PLC HUMAN MACHINE INTERFACES " Displays present setting ENERGY CONSUMPTION VISUALIZATION COMPONENTS Light state FA COMPONENTS MACHINE VISION SYSTEMS Dark state UV CURING SYSTEMS Displays selected setting Timer operation setting * The setting for whether the timer is used or not can be done when MODE indicator / TIMER (yellow) lights up. For FX-301B/G/H, the timer type can be set in PRO mode. * Further, an OFF-delay (initial value) which is useful when the response of the connected device is slow, etc., an ON-delay which is useful to detect only objects taking a long time to travel, and ONE SHOT, which is useful when the input specifications of the connected device require a signal of a fixed width, are possible with the FX-301(-HS). FX-305(P) is also equipped with ON-delay * OFF-delay and ON-delay * ONE SHOT timers. Refer to the "PRO Mode Operation Guide" for the setting method of the OFF-delay, ON-delay and ONE SHOT timer intervals. Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F 163 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES Digital Fiber Sensor FX-300 SERIES PRECAUTIONS FOR PROPER USE Refer to p.1458~ for general precautions and to the "PRO mode operation guide" on our website for details pertaining to operating instructions for the amplifier. Key-lock function Wiring * Make sure that the power supply is off while wiring. * Verify that the supply voltage variation is within the rating. * Take care that if a voltage exceeding the rated range is applied, or if an AC power supply is directly connected, the product may get burnt or damaged. * If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground. * In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground. * Take care that short circuit of the load wrong wiring may burn or damage the product. * Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction. * Make sure to use an isolation transformer for the DC power supply. If an autotransformer (single winding transformer) is used, this product or the power supply may get damaged. * Make sure to use the optional quick-connection cable for the connection of the amplifier. Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (5-8 unit expansion: 50 m 164.042 ft, 9-16 unit expansion: 20 m 65.617 ft) However, in order to reduce noise, make the wiring as short as possible. * Note that the residual voltage will increase when the cable is extended. * If jog switch and MODE key are pressed for more than 2 sec. at the same time in `RUN' mode condition, the key operations are locked, and only the threshold value confirmation function or the adjust function (valid only when the adjust lock function is canceled) is valid. To cancel the lock function, press both the keys for more than 2 sec. once again. Note: 3 seconds or more for FX-301B/G/H(P). Others * When the emission halt of the light emitting amount selection function is set from "OFF" to "ON", the output may be unstable. Do not use the output control for 0.5 sec. after starting emission. * Do not use during the initial transient time (0.5 sec.) after the power supply is switched on. * Take care that the sensor is not directly exposed to fluorescent lamp from a rapid-starter lamp, a high frequency lighting device or sunlight etc. , as it may affect the sensing performance. * Do not use this sensor in places having excessive vapor, dust, etc., or where it may come in contact with corrosive gas. * Take care that the product does not come in direct contact with water, oil, grease, or organic solvents, such as, thinner, etc. * This sensor cannot be used in an environment containing inflammable or explosive gases. * Never disassemble or modify the sensor. ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Function table for FX-300 series Previous models Standard type FX-301(P) (Previous version unit) Selection Guide Fibers Fiber Amplifiers New models High-function type High-speed type FX-302(P) FX-303(P) Standard type FX-301(P) (Updated version unit) High-speed type High-function type FX-301(P)-HS FX-305(P) Four-chemical emitting element + APC circuit No No No Yes Yes Yes Four-chemical emitting element only Yes (Note) Yes Yes - - - Light emitting amount selection function No No No Yes Yes Yes Reduced intensity mode (S-D) Yes (Note) Yes No Yes Yes - 9,999 digit display No No No No No Yes FX-500 Response time (Max. speed) 150 s 300 s 90 s 65 s 35 s 65 s FX-100 Interference prevention function (Effective no. of units) Incorporated (4) Incorporated (8) Not incorporated (0) Incorporated (4) Not incorporated (0) Incorporated (16) FX-300 Independent 2 outputs No No No No No Yes Alarm output function No No No No No Yes Error output function No No No No No Yes Differential sensing No No No No No Yes Window comparator mode No Yes No No No Yes FX-410 FX-311 FX-301-F7/ FX-301-F Peripheral units that can be combined Bank selection unit FX-CH(-P) Yes Yes No No No No External input unit FX-CH2(-P) No No No Yes No Yes Upper communication unit SC-GU1-485 No No No Yes No Yes Note: Except FX-301B/G/H. Digital Fiber Sensor PRECAUTIONS FOR PROPER USE * The product has been modified as shown below since its production in June 2004. Changes in appearance Top view After change Top view Name plate Display Uses special parts Side view 1. Timer selection method Previous version unit: Timer type was changed using PRO1 mode. The "TIMER" setting in NAVI mode could only be turned on or off. After change: T he type of timer can be changed using the "TIMER" function in NAVI mode. Display changes Change in shape of jog switch * "NAVI" is printed on the both sides * "NAVI" is printed only on a side 1. Checking blinking of sensitivity surplus The stable surplus display method after teaching has been changed. Previous version unit: Sensitivity surplus is indicated by the number of blinks of the stability indicator. After change 1. Response times added An ultra high-speed mode (H-SP) has been added to the existing 4 response time modes [high-speed (FAST), reduced intensity (S-D), standard (STD) and long range (LONG)]. This is changed using " " in " " Before change 4 steps 2. Initial direct code value changed The factory default settings for the direct codes have been changed. Previous version unit 0000 Upgraded functions After change After change 0004 *T he default setting for the timer period is 10 ms, and the direct code for 10 ms is "4", so this has been changed. Internal circuit changes 1. Addition of an APC circuit A four-chemical emitting element which provides stable sensing over* long* periods* has been added, as well as an APC (Auto Power Control) circuit that improves stability during short periods. Cautions on sensor connection in cascade 5 steps 150 s (FAST) 65 s (added) (H-SP) 250 s (S-D) 150 s (FAST) 250 s (STD) 250 s (S-D) 2 ms (LONG) 250 s (STD) PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS Digital display only * Checking minor changes between previous and updated models can be done by checking whether the printing is on both sides or only one side. FIBER SENSORS LASER SENSORS Changes in operation 2. Checking threshold value in RUN mode The threshold values can be checked by turning the jog switch. Added to name plate Side view 164 Refer to p.1458~ for general precautions and to the "PRO mode operation guide" on our website for details pertaining to operating instructions for the amplifier. A difference between the updated version unit and the previous version unit for FX-301(P) (Red LED type) Before change FX-300 SERIES When connecting the previous version unit (including FX-301B/G/H) and updated version unit to be used in a cascade, refer to "Cautions on sensor connection in cascade". WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS 2 ms (LONG) 2. Extension of timer period The setting range for the timer period was previously 500 ms, but this has been extended to a new range of 9,999 ms. 3. Light emitting amount selection function The light emitting amount can be changed to one of 4 levels (5 levels when emission halt is included). 4. Backup, copy lock and key lock functions added Backup: This selects whether or not threshold values set by teaching are written to (stored in) an EEPROM. Copy lock: This selects whether copy function and data bank function communication are possible or not. Key lock: This disables input using switches to prevent accidental changing of settings. Selection Guide Fibers Fiber Amplifiers FX-500 FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F 165 FIBER SENSORS Digital Fiber Sensor FX-300 SERIES PRECAUTIONS FOR PROPER USE Refer to p.1458~ for general precautions and to the "PRO mode operation guide" on our website for details pertaining to operating instructions for the amplifier. LASER SENSORS Diagram of functions and settings PHOTOELECTRIC SENSORS The amplifier features and settings are generally classified into two main modes; the "NAVI mode" for items and settings that are frequently reconfigured, and the "PRO mode" that contains more detailed settings. MICRO PHOTOELECTRIC SENSORS RUN AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS TEACH Run This indicates normal sensing operation. NAVI mode PRO INDUCTIVE PROXIMITY SENSORS TIMER Pro Allows various detailed settings to be configured, such as optical communications, save / load and other settings. PARTICULAR USE SENSORS Teaching The "threshold value" can be set by utilizing either "2-point teaching", "limit teaching", or "full-auto teaching". * When the FX-305(P) is in window comparator mode, the "threshold value" can be set by either "1-point teaching", "2-point teaching" or "3-point teaching". ADJ Allows fine adjustment of the "threshold value". L/D Timer Configures operation of the timer. Adjust L-ON / D-ON Sets output operation either Light-ON, or Dark-ON. SENSOR OPTIONS Response Time Change SIMPLE WIRE-SAVING UNITS PRO1 Switches among response times. WIRE-SAVING SYSTEMS MEASUREMENT SENSORS LASER MARKERS PRO2 Allows selection of different content to be indicated in the digital display. HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS PRO3 PRO mode Sets the viewing orientation of the digital display. Data Bank Save Loads configuration setting from the data bank. Saves configuration setting into the data bank. Copy PRO4 * The FX-301(P)-HS is not equipped with a PRO4 setting function. Backup Allows not to save the threshold value, by teaching via external input in EEPROM. [FX-301(P), FX-305(P) only] Selection Guide Fibers Fiber Amplifiers PRO5 Remote Data Bank Save Using optical communication, current configuration settings can be saved into respective data banks all at once. Communication Change To Permit / Not to Permit When using optical communication for carrying out copy / load / save operations all at once, this function allows optical communication to pass through the unit. Verifies whether optical communications have been properly established. (FX-301B/G/H only) Allows fine adjustment of the "threshold value" to be directly performed during RUN mode. The items that can be set are different for output 1 and output 2. Normal Mode PRO6 Sets a threshold value for ON / OFF operation. Reset All settings, except for data bank information, revert to factory settings. Interference Prevention Switching Switches the number of units for which interference prevention switching is enabled. * FX-305(P) only. FX-410 Available only in FX-305(P) Test Adjust Lock Allows basic configuration information to be set in a single step, by inputting a 4-digit code. FX-300 FX-311 Sets the digital display to turn ON / OFF. Remote Data Bank Load FX-100 FX-301-F7/ FX-301-F ECO Mode Using optical communication, configuration settings can be loaded from respective data banks all at once. Code FX-500 Stability Permits selection of stability indicator response levels for changes in the range for lighting up. [excluding the FX-305(P)] Digital Display Inversion Data Bank Load Using optical communications, configuration settings from the main unit are copied to connected sub units all at once. Sets hysteresis level. Shift Shifts the "threshold value" by a certain percentage increment in "limit teaching". Digital Display Setting PLC FA COMPONENTS Configures timer operation. Light Emitting Amount Selection Changes the light emitting amount selection setting. [FX-301(P)(-HS), FX-305(P) only] STATIC ELECTRICITY PREVENTION DEVICES Hysteresis Timer Setting Rising Differential Mode Window Comparator Mode Output 1 Judges if set two threshold values are within the required range or not. This can be selected in 1-point / 2-point / 3-point teaching. Sensing mode that cancels out slight changes in light intensity so that only sudden increases in incident light intensity are sensed. Output 2 Error Output Alarm Output Trailing Differential Mode Output when overcurrent occurs or when a communication error occurs from connected incompletely. Be used as alarm output when the threshold value for output 2 is linked to output 1 and the light amount drops. Sensing mode that cancels out slight changes in light intensity so that only sudden decreases in incident light intensity are sensed. * The 0-ADJ setting function equipped on the FX-301 and FX-305(P) has been deleted since the production in May 2005. Digital Fiber Sensor DIMENSIONS (Unit: mm in) PHOTOELECTRIC SENSORS 12 0.472 AREA SENSORS MODE key Jog switch Digital display (Red) 3 0.118 64.5 2.539 Communication window Beamemitting part 7 0.276 Beamreceiving part MICRO PHOTOELECTRIC SENSORS 0.7 0.028 Stability indicator (Green) (Note 2) 10 0.394 LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS 3.3 0.130 27.8 1.094 INDUCTIVE PROXIMITY SENSORS 7 0.276 30.5 1.201 PARTICULAR USE SENSORS 10.5 0.413 7 0.276 3 0.118 13.5 0.531 SENSOR OPTIONS (Note 3) SIMPLE WIRE-SAVING UNITS 3.95 0.156 Suitable for 35 mm 1.378 in width DIN rail 36.5 1.437 WIRE-SAVING SYSTEMS Notes: 1) FX-305; Output 1 operation indicator (Orange) 2) FX-305; Output 2 operation indicator (Orange) 3) FX-301; 3-pin, FX-305; 4-pin CN-73-C CN-74-C MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES Main cable (Optional) * Length L L 50 1.969 CN-71-C CN-72-C Sub cable (Optional) * Length L Model No. Length L Model No. Length L 1,000 39.370 CN-71/72-C1 1,000 39.370 CN-73/74-C2 2,000 78.740 CN-71/72-C2 2,000 78.740 CN-73/74-C5 5,000 196.850 CN-71/72-C5 5,000 196.850 o3.3 o0.130 cable 14 (0.551 ) 2.54 0.100 2.65 0.104 (Note 2) 2.9 (0.114 ) 10 0.394 6 0.236 ( ) 12 10.5 (0.472 ) 0.413 2.54 0.100 Notes: 1) CN-74-C only 2) CN-73-C; 3-core 7 0.276 10 0.394 13.6 0.535 3 0.118 (Note 2) ( 14 0.551 ) 3 0.118 2.9 (0.114 ) 2.54 0.100 HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS 10 0.394 6 0.236 ( ) FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS 12 10.5 (0.472 ) 0.413 2.65 0.104 7.2 0.283 50 1.969 o3.3 o0.130 cable 2.54 0.100 (Note 1) 0.2 0.008 LASER MARKERS PLC L CN-73/74-C1 (Note 1) FIBER SENSORS LASER SENSORS Amplifier 48.2 26.3 1.898 1.0352.5 0.098 166 The CAD data in the dimensions can be downloaded from our website. FX-301 FX-305(P) 8.3 Operation indicator (Orange) (Note 1) 0.327 FX-300 SERIES 0.2 0.008 Notes: 1 ) CN-72-C only 2) CN-71-C: 1-core 7 0.276 10 0.394 13.6 0.535 3 0.118 7.2 0.283 Selection Guide Fibers MS-DIN-2 Amplifier mounting bracket (Optional) 21.6 0.850 16 0.630 5.2 0.205 MS-DIN-E End plate (Optional) 2.75 0.108 3.2 0.126 FX-500 10 0.394 8.5 0.335 3.2 0.126 0.4 0.016 o1.8 o0.071 7.5 0.295 4.2 0.165 5.2 0.205 35 1.378 2 0.079 2 0.079 2-o3.2 o0.126 holes Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) 5 0.197 15 0.591 60 2.362 3 0.118 5.6 M3 square nut 0.220 24.7 0.972 t1 t 0.039 27 1.063 M3 (length 18 mm 0.709 in) pan head screws 3 0.118 1.6 0.063 Fiber Amplifiers 32 1.260 Material: Polycarbonate 4 0.157 Suitable for 35 mm 1.378 in width DIN rail FX-100 FX-300 FX-410 FX-311 FX-301-F7/ FX-301-F