SCOPE: DUAL POWER MOSFET DRIVER Device Type 01 02 03 Generic Number TSC426M(x)/883B TSC427M(x)/883B TSC428M(x)/883B Circuit Function Dual Power Inverting MOSFET Driver Dual Power Noninverting MOSFET Driver Dual Power Inverting/Noninverting MOSFET Driver Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Outline Letter JA NP Mil-Std-1835 GDIP1-T8 or CDIP2-T8 CQCC1-N20 Case Outline Package Code 8 LEAD CERDIP J8 20 Leadless Carrier L20 Absolute Maximum Ratings Supply Voltage VDD to GND ................................................................................... 20V Input Voltage .........................................................................VDD +0.3V to GND -0.3V Output Current (per pin, capacitive load) ............................................................... 1.5A Peak Supply Current or GND Current (per pin) ..................................................... 3.0A Lead Temperature (soldering, 10 seconds) ....................................................................... +300C Storage Temperature .......................................................................................... -65C to +150C Continuous Power Dissipation ............................................................................. TA=+70C 8 pin CERDIP(derate 8.0mW/C above +70C) ........................................................ 640mW 20 pin LCC(derate 9.1mW/C above +70C) ............................................................ 727mW Junction Temperature TJ ......................................................................................... +150C Thermal Resistance, Junction to Case, JC 8 pin CERDIP..................................................................................................... 55C/W 20 pin LCC ........................................................................................................ 20C/W Thermal Resistance, Junction to Ambient, JA: 8 pin CERDIP................................................................................................... 125C/W 20 pin LCC ...................................................................................................... 110C/W Recommended Operating Conditions Ambient Operating Range (TA) ............................................................. -55C to +125C Supply Voltage Range .............................................................................. 4.5VVDD18V 01 01 02 02 03 03 Package 8 pin CERDIP 20 pin LCC 8 pin CERDIP 20 pin LCC 8 pin CERDIP 20 pin LCC ORDERING INFORMATION: TSC426MJA/883B TSC426MNP/883B TSC427MJA/883B TSC427MNP/883B TSC428MJA/883B TSC428MNP/883B SMD Number 5962-8850301PA 5962-88503012C 5962-8850302PA 5962-88503022C 5962-8850303PA 5962-88503032C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of TSC426/427/428/883B for SMD 5962-88503 19-0385 Page 2 of Rev. B 5 TABLE 1. ELECTRICAL TESTS: TEST CONDITIONS -55 C <=TA<= +125C +4.5VVS18V Unless otherwise specified Symbol Group A Subgroup 1,2,3 Device type Limits Min All All All All 2.4 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 All All All VDD-25 1,2,3 NOTE 2 1 2,3 1 2,3 9,10,11 VDD=18V NOTE 2 Logic 1 Input Voltage Logic 0 Input Voltage Input Voltage Range Input Current VIH VIL VIN(max) IIN Output High Voltage Output Low Voltage Output Resistance VOH VOL ROUT Output Resistance ROUT Power Supply Current IS1 RL= NOTE 1 RL= NOTE 1 Apply VIN to force VOUT high. VDD=18V, IOUT=10mA, VIN=0.8V for inverting stages, VIN=2.4V for noninverting stages Apply VIN to force VOUT low. VDD=18V, IOUT=10mA, VIN=0.8V for noninverting stages VIN=2.4V for inverting stages VIN=+3V, both inputs Power Supply Current IS2 VIN=0V, both inputs Rise Time NOTE 2 tR VDD=18V Fall Time NOTE 2 tF VIN =0V to 18V Limits Max 0.8 VDD 1 10 0 Units V V V A 25 20 mV mV All 15 01 mA mA All 8 12 0.4 0.6 60 9,10,11 All 40 ns 01 ns Delay Time NOTE 1 tD1 VDD=18V NOTE 2 9,10,11 All 60 ns Delay Time NOTE 1 tD2 VDD=18V NOTE 2 9,10,11 All 120 ns NOTE 1: Guaranteed by design. NOTE 2: Subgroups 10 and 11 are guaranteed if not tested to the limits specified in Table 1. TERMINAL CONNECTIONS FOR 01, 02, 03. 8 PIN CERDIP 01 02 03 01 1 NC NC NC 1 NC 2 INA INA INA 2 NC 3 GND GND GND 3 NC 4 INB INB INB 4 INA 5 6 7 8 _____ OUTB VDD _____ OUTA NC 02 NC NC NC INA 20 PIN LCC 03 NC 11 NC 12 NC 13 INA 14 OUTB OUTB 5 NC NC NC 15 01 NC NC NC _____ OUTB NC VDD OUTA VDD _____ OUTA NC 6 7 GND NC GND NC GND NC 16 17 VDD NC VDD NC VDD NC 8 INB INB INB 18 OUTA 9 10 NC NC NC NC NC NC 19 20 _____ OUTA NC NC _____ OUTA NC NC NC ---------------------------- Electrical Characteristics of TSC426/427/428/883B for SMD 5962-88503 02 NC NC NC OUTB 03 NC NC NC OUTB NC NC NC NC 19-0385 Page 3 of Rev. B 5 QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * ** Subgroups per Method 5005, Table 1 1 1*, 2, 3, 9, 10**, 11** 1, 2, 3, 9, 10**, 11** 1 PDA applies to Subgroup 1 only. Subgroups 10 and 11, if not tested, shall be guaranteed to the specified limits of Table 1. ---------------------------- Electrical Characteristics of TSC426/427/428/883B for SMD 5962-88503 19-0385 Page 4 of Rev. B 5 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: 5962-8850302PA