SCOPE: DUAL POWER MOSFET DRIVER
Device Type Generic Number Circuit Function
01 TSC426M(x)/883B Dual Power Inverting MOSFET Driver
02 TSC427M(x)/883B Dual Power Noninverting MOSFET Driver
03 TSC428M(x)/883B Dual Power Inverting/Noninverting MOSFET Driver
Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows:
Outline Letter Mil-Std-1835 Case Outline Package Code
JA GDIP1-T8 or CDIP2-T8 8 LEAD CERDIP J8
NP CQCC1-N20 20 Leadless Carrier L20
Absolute Maximum Ratings
Supply Voltage VDD to GND ................................................................................... 20V
Input Voltage .........................................................................VDD +0.3V to GND -0.3V
Output Current (per pin, capacitive load) ............................................................... 1.5A
Peak Supply Current or GND Current (per pin) ..................................................... 3.0A
Lead Temperature (soldering, 10 seconds) ....................................................................... +300°C
Storage Temperature .......................................................................................... -65°C to +150°C
Continuous Power Dissipation ............................................................................. TA=+70°C
8 pin CERDIP(derate 8.0mW/°C above +70°C) ........................................................ 640mW
20 pin LCC(derate 9.1mW/°C above +70°C) ............................................................ 727mW
Junction Temperature TJ .....................................................................................…. +150°C
Thermal Resistance, Junction to Case, ΘJC
8 pin CERDIP..................................................................................................... 55°C/W
20 pin LCC ........................................................................................................ 20°C/W
Thermal Resistance, Junction to Ambient, ΘJA:
8 pin CERDIP................................................................................................... 125°C/W
20 pin LCC ...................................................................................................... 110°C/W
Recommended Operating Conditions
Ambient Operating Range (TA) ............................................................. -55°C to +125°C
Supply Voltage Range .............................................................................. 4.5V≤VDD≤18V
Package ORDERING INFORMATION: SMD Number
01 8 pin CERDIP TSC426MJA/883B 5962-8850301PA
01 20 pin LCC TSC426MNP/883B 5962-88503012C
02 8 pin CERDIP TSC427MJA/883B 5962-8850302PA
02 20 pin LCC TSC427MNP/883B 5962-88503022C
03 8 pin CERDIP TSC428MJA/883B 5962-8850303PA
03 20 pin LCC TSC428MNP/883B 5962-88503032C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
---------------------------- Electrical Characteristics of TSC426/427/428/883B 19-0385 Rev. B
for SMD 5962-88503 Page 2 of 5
TABLE 1. ELECTRICAL TESTS:
TEST Symbol
CONDITIONS
-55 °C <=TA<= +125°C
+4.5V≤VS≤18V
Unless otherwise specified
Group A
Subgroup
Device
type Limits
Min
Limits
Max
Units
Logic 1 Input Voltage VIH 1,2,3 All 2.4 V
Logic 0 Input Voltage VIL 1,2,3 All 0.8 V
Input Voltage Range VIN(max) 1,2,3 All 0V
DD V
Input Current IIN VIN =0V to 18V 1,2,3 All ±1
±10
µA
Output High Voltage VOH RL=∞ NOTE 1 1,2,3 All VDD-25 mV
Output Low Voltage VOL RL=∞ NOTE 1 1,2,3 All 25 mV
Output Resistance ROUT Apply VIN to force VOUT high.
VDD=18V, IOUT=10mA,
VIN=0.8V for inverting stages,
VIN=2.4V for noninverting stages
1,2,3 All 20 Ω
Output Resistance ROUT Apply VIN to force VOUT low.
VDD=18V, IOUT=10mA,
VIN=0.8V for noninverting stages
VIN=2.4V for inverting stages
1,2,3 All 15 Ω
Power Supply Current IS1 VIN=+3V, both inputs 1
2,3
01 8
12
mA
Power Supply Current IS2 VIN=0V, both inputs 1
2,3
01 0.4
0.6
mA
Rise Time NOTE 2 tRVDD=18V NOTE 2 9,10,11 All 60 ns
Fall Time NOTE 2 tFVDD=18V NOTE 2 9,10,11 All 40 ns
Delay Time NOTE 1 tD1 VDD=18V NOTE 2 9,10,11 All 60 ns
Delay Time NOTE 1 tD2 VDD=18V NOTE 2 9,10,11 All 120 ns
NOTE 1: Guaranteed by design.
NOTE 2: Subgroups 10 and 11 are guaranteed if not tested to the limits specified in Table 1.
TERMINAL CONNECTIONS FOR 01, 02, 03.
8 PIN CERDIP 20 PIN LCC
01 02 03 01 02 03 01 02 03
1 NC NC NC 1 NC NC NC 11 NC NC NC
2 INA INA INA 2 NC NC NC 12 NC NC NC
3 GND GND GND 3 NC NC NC 13 NC NC NC
4 INB INB INB 4 INA INA INA 14 _____
OUTB
OUTB OUTB
5 _____
OUTB
OUTB OUTB 5 NC NC NC 15 NC NC NC
6V
DD VDD VDD 6 GND GND GND 16 VDD VDD VDD
7 _____
OUTA
OUTA _____
OUTA
7NC NC NC 17NC NC NC
8 NC NC NC 8 INB INB INB 18 _____
OUTA
OUTA _____
OUTA
9NC NC NC 19NC NC NC
10 NC NC NC 20 NC NC NC
---------------------------- Electrical Characteristics of TSC426/427/428/883B 19-0385 Rev. B
for SMD 5962-88503 Page 3 of 5
QUALITY ASSURANCE
Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-
Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125°C minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,
C, and D inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883:
1. Test condition A, B, C, D.
2. TA = +125°C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2. ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements Subgroups
per Method 5005, Table 1
Interim Electric Parameters
Method 5004
1
Final Electrical Parameters
Method 5005
1*, 2, 3, 9, 10**, 11**
Group A Test Requirements
Method 5005
1, 2, 3, 9, 10**, 11**
Group C and D End-Point Electrical Parameters
Method 5005
1
* PDA applies to Subgroup 1 only.
** Subgroups 10 and 11, if not tested, shall be guaranteed to the specified limits of Table 1.
---------------------------- Electrical Characteristics of TSC426/427/428/883B 19-0385 Rev. B
for SMD 5962-88503 Page 4 of 5
