1/5
■GOOD CONSUMPTION/SPEED RATIO :
ONLY 200µA FOR 2.1MHz, 2Vµs
■SINGLE (OR DUAL) SUPPLY OPERATION
FROM +4V TO +44V (±2V TO ±22V)
■WIDE INPUT COMMON MODE MODE
VOLTAGE RANGE INCLUDING VCC-
■LOW LEVEL OUTPUT VOLTAGE CLO SE TO
VCC- : 100mV TYPICAL
■PIN TO PI N COMPATIBLE WITH
STANDARD QUAD OP-AMPs
DESCRIPTION
The M C3x 174 series are quad bip olar operationa l
amplifier offering both low consumption (200µA)
and good sp eed (2.1MHz , 2V/µs ).
Moreover the Input Common Mode Range ex-
tends down to the l ower suppl y rail, allowing single
supply operation from +4V to +44V.
ORDER CODE
N = Dual in Line Package (DIP)
D = Sm all Outline Package (SO) - also av ailable in Tape & Reel (DT))
PIN CONNECTIONS (top view)
Part Number Temperature
Range Package
ND
MC33174 -40°C, +105°C ••
MC35174 -55°C, +125°C ••
Example : MC33174N
N
DIP14
(Plastic Package)
D
SO14
(Plastic Microp acka ge)
Inverting Input 2
Non-inverting Input 2
Non-inverting Input 1
CC
V -
CC
V
1
2
3
4
8
5
6
7
9
10
11
12
13
14
+
Output 3
Output 4
Non-inverting Input 4
Inverting Input 4
Non-inverting Input 3
Inverting Input 3
-
+
-
+
-
+
-
+
Output 1
Inverting Input 1
Output 2
MC33174 - MC35174
LOW POWER
QUAD BIPOLAR OPERATIONAL AMPLIFIERS
April 2002
MC33174-MC35174
2/5
SCHEMATIC DIAGRAM (for 1/4 MC33174)
MAXIMUM RATINGS
OPERATING CONDITIONS
Symbol Parameter Value Unit
VCC Supply Voltage ±22 V
Vid Differential Input Voltage see note 1)
1. Either or both input voltages must not exceed the magnitude of Vc c.
V
ViInput Voltage see note 1 V
Output Short Circuit Duration Indefinite s
Toper Operating Free-Air Temperature range MC33174
MC35174 -40 to 105
-55 to 125 °C
TjJunction Temperature 150 °C
Tstg Storage Temperature -65 to 150 °C
Symbol Parameter Value Unit
VCC Supply Voltage ±2 to ±22 V
V +
CC
T1 T7
R4
T8 T9
R3
T6
T2
T5
T3
R1
T4 R2
T13
T14
T19
R5
R7 R8
T10 T11
R6
T15 T16
R9
T20
R10
T17
Input +
T12 T13
T24
C
T21
T22
R11 T23
T27
T29
R12
R15 T30 T31
T28
R14
Output
R13
V -
CC
Input -
T25
T26
MC33174-MC35174
3/5
ELECTRICAL CHARACTERISTICS
VCC+ = +1 5V, VCC- = -15V, RL connected to Ground, Tamb = 25°C (unless otherwise specified)
Symbol Parameter Min. Typ. Max. Unit
Vio
Input Offset Voltage
VCC+ = +15V, VCC- = -15V, Vic = 0V
VCC+ = 5V, VCC- = 0V, Vic = 0V, Vo = 1.4V
VCC+ = +15V, VCC- = -15V, Vic = 0V, Tmin. ≤ Tamb ≤ Tmax.
1
14.5
5
6.5
mV
DVio Input Offset Voltage Drift 10 µV/°C
Iio Input Offset Current (Vic = 0V)
Tmin. ≤ Tamb ≤ Tmax. 520
40 nA
Iib Input Bias Current (Vic = 0V)
Tmin. ≤ Tamb ≤ Tmax. 20 100
200 nA
Avd Large Signal Voltage Gain (RL = 10kΩ, Vo = ±10V)
Tmin. ≤ Tamb ≤ Tmax. 50
25 100 V/mV
VOH
High Level Output Voltage
VCC+ = 5V, VCC- = 0V, RL = 10kΩ
VCC+ = +15V, VCC- = -15V, RL = 10kΩ
VCC+ = +15V, VCC- = -15V, RL = 10kΩ, Tmin. ≤ Tamb ≤ Tmax
3.5
13.6
13.3
4.2
14.2 V
VOL
Low Level Output Voltage
VCC+ = 5V, VCC- = 0V, RL = 10kΩ
VCC+ = +15V, VCC- = -15V, RL = 10kΩ
VCC+ = +15V, VCC- = -15V, RL = 10kΩ, Tmin. ≤ Tamb ≤ Tmax
0.1
-14 0.15
-13.6
-13.3
V
Isc Output Short Circuit Current (Vid = ±1V, Vo = 0V)
Source
Sink 3
15 6
27 mA
Vicm Input Common Mode Voltage Range
Tmin. ≤ Tamb ≤ Tmax
VCC- to (VCC+ - 1.8)
VCC- to (VCC+ - 2.2) V
CMR Common-mode Rejection Ratio (Vic = Vicm min.)80 100 dB
SVR Supply Voltage Rejection Ratio (VCC = ±5 to ±15V) 80 100 dB
ICC
Supply Current
VCC+ = 5V, VCC- = 0V, no load
VCC+ = +15V, VCC- = -15V, no load
VCC+ = +15V, VCC- = -15V, no load, Tmin. ≤ Tamb ≤ Tmax
200
220 250
250
300
µA
SR Slew Rate (Vi = ±10V, RL = 10kΩ, CL = 100pF) 1.6 2 V/µs
GBP Gain Bandwidth Product
RL = 10kΩ, CL = 100pF, f = 100kHz 1.4 2.1 MHz
φmPhase Margin (RL = 10kΩ, CL = 100pF) 45 Degrees
enEquivalent Input Noise Voltage (f = 1kHz) 29
THD Total Harmonic Distortion 0.05 %
VO1/VO2 Channel Separation 120 dB
nV
Hz
------------
MC33174-MC35174
4/5
PACKAGE MECHANICAL DATA
14 PINS - PLASTIC DIP
Dimensions Millimeters Inches
Min. Typ. Max. Min. Typ. Max.
a1 0.51 0.020
B 1.39 1.65 0.055 0.065
b 0.5 0.020
b1 0.25 0.010
D 20 0.787
E 8.5 0.335
e 2.54 0.100
e3 15.24 0.600
F 7.1 0.280
i 5.1 0.201
L 3.3 0.130
Z 1.27 2.54 0.050 0.100
MC33174-MC35174
5/5
PACKAGE MECHANICAL DATA
14 PINS - PLASTIC MICROPACKAGE (SO)
Dimensions Millimeters Inches
Min. Typ. Max. Min. Typ. Max.
A 1.75 0.069
a1 0.1 0.2 0.004 0.008
a2 1.6 0.063
b 0.35 0.46 0.014 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.020
c1 45° (typ.)
D (1) 8.55 8.75 0.336 0.344
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 7.62 0.300
F (1) 3.8 4.0 0.150 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.020 0.050
M 0.68 0.027
S 8° (max.)
Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DA TA BOOK.
DM
F
14
17
8
be3 eE
LG
C
c1
A
a2
a1
b1
s
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No l i cense is gra nte d by imp lication or oth erwise under any patent or patent rights of STMicroelec tronics. Spec ificat ions
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems with out expres s written approval of STMicroelec tronics .
© The ST logo is a registered trademark of STMicroelectronic s
© 2002 ST M icroele ctron ics - Pr i n ted in Italy - All Ri g h ts Reserved
STM icr o el ectron ics GROUP OF COM PANI ES
Austral i a - Br azil - Canada - China - Finl and - France - Ge rm any - Hong Ko ng - Ind i a - Is rael - Ita l y - J apan - M al aysi a
Malta - Moroc co - Sin gapore - Spai n - Sw eden - Swi tze rl and - U nited K i ngdom - United Sta tes
© http://www.st.com
