FR801 THRU FR807
Features
Mechanical Data
· Fast switching
· Low leakage
· Low forward voltage drop
· High current capability
· High current surge
· High reliability
Maximum Ratings And Electrical Characteristics
· Case : JEDEC TO-220A molded plastic body
· Terminals : Lead solderable per
MIL-STD-750, method 2026
· Polarity : As marked
· Mounting Position : Any
· Weight : 0.08 ounce, 2.24 gram
(Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive
load. For capacitive load, derate by 20%)
Notes:
(1) Test conditions: I
F=0.5A, IR=1.0A, Irr=0.25A.
(2) Measured at 1MHz and applied reverse voltage of 4.0 Volts.
(3) Thermal resistance from junction to case, single side cooled.
CURRENT 8.0 Amperes
VOLTAGE 50 to 1000 Volts
Maximum recurrent peak reverse voltage
Maximum RMS voltage
Maximum DC blocking voltage
Volts
Peak forward surge current 8.3ms single
half sine-wave superimposed on rated load
(JEDEC method)
V
DC
Maximum average forward rectified current
at T
C
=55℃
Maximum instantaneous forward voltage
at 8.0A
V
RRM
Volts
Symbols Units
1.3
3.0
V
F
V
RMS
8.0
Amps
Amps
I
FSM
T
J
T
STG
-55 to +150 ℃
℃/W
Volts
Maximum DC reverse current
at rated DC blocking voltage
Maximum reverse recovery time (Note 1)
T
C
=25℃
T
C
=125℃
Typical junction capacitance (Note 2) T
J
=25℃
Typical thermal resistance (Note 3)
Operating junction and storage
temperature range
50
FR
801
35
50
10
100
250
Volts
μA
ns
pF
I
(AV)
I
R
Trr
60
C
J
100
FR
802
70
100
200
FR
803
140
200
400
FR
804
280
400
600
FR
805
420
600
800
FR
806
560
800
1000
FR
807
700
1000
500150
150
Dimensions in inches and (millimeters)
TO-220A
.412
.248
.040
.158
.595
.550
.200
.051
.040
.108
(10.5)
(6.3)
(1.0)
(4.0)
(15.1)
(14.0)
(5.08)
(1.3)
(1.0)
(2.75)
MAX.
MAX.
MAX.
MAX.
MIN.
MAX.
MAX.
3.8 +.2
HOLE THRU
f
++
++
PIN 1
PIN 2 CASE
Case Positive
.180
.050
.120
(4.6)
(1.27)
(3.05)
++
PIN 1
PIN 2 CASE
Case Negative
Suffix "R"
Rθ
JC
RATINGS AND CHARACTERISTIC CURVES FR801 THRU FR807
trr
1cm
50
NONINDUCTIVE 10
NONINDUCTIVE
DUT
OSCILLOSCOPE
(NOTE 1 )
(+ )
50Vdc
(approx)
(-)
NOTES: 1 . RISE TIME = 7ns max. INPUT
IMPEDANCE= 1 MEGOHM 22pf
2 . RISE TIME = 10ns max. SOURSE
IMPEDANCE = 50ohmsf
+0.5A
-1.0A
SET TIME BASE FOR
5/ 10ns / cm
NONINDUCTIVE
PULSE
GENERATOR
( NOTE 2 ) -0.25A
0
FIG . -REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
1
FIG . 2- MAXIMUM FORWARD CURRENT DERATING CURVE
AVERAGE FORWARD CURRENT ( A )
FIG . 5 - TYPICAL INSTANTANEOUS
FORWARD CARACTERISTICS
0 50 100 150
10
8
6
4
2
0
O
LEAD TEMPERATURE . ( C )
.6 .8 1.0 1.2 1.4 1.6 1.8 2.0
INSTANTANEOUS FORWARD VOLTAGE . ( A )
INSTANTANEOUS FORWARD VOLTAGE . ( A )
400
200
100
40
20
10
1
2
4
0.1
0.2
0.4
1 2 5 10 20 50 1 00
150
125
100
75
50
25
0.1 0.5 1.0 5 10 50 100 500 1000
120
100
80
60
40
20
0 20 40 60 80 100 120 140
100
40
10
4
2
1.0
.4
.2
.1
PERCENT OF RATED PEAK REVERSE
VOLTAGE. ( % )
REVERSE VOLTAGE . ( V )
FIG . 4 - TYPICAL HUNCTION CAPACITANCE
NUMBER OF CYCLES AT 60Hz
FIG . 3 - MAXIMUM NON - REPETITIVE FORWARD
SURGE CURRENT
FIG . 6 - TYPICAL REVERSE CHARACTERISTICS
PEAK FORWARD SURGE
CURRENT . ( A )
CAPACITANCE . ( pF )
INSTANTANEOUS REVERSE CURRENT . ( A)
8.3ms Single Half Sine
Wave
JEDEC Method
O
TC = 125 C
Pulse Width=300 s
1% Duty Cycle
O
Tj=25 C
O
Tj=125 C
O
Tj=75 C
O
Tj=25 C
O
Tj=25 C
f = 1.0MHz
Vsig = 50mVp-p