IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCKTM IDT5T2110 NRND Not Recommended for New Designs FEATURES: * * * * * * * * * * * * * * DESCRIPTION: 2.5 VDD 6 differential outputs Low skew: 100ps all outputs Selectable positive or negative edge synchronization Tolerant of spread spectrum input clock Synchronous output enable Selectable inputs Input frequency: 4.17MHz to 250MHz Output frequency: 12.5MHz to 250MHz 1.8V / 2.5V LVTTL: up to 250MHz HSTL / eHSTL: up to 250MHz Hot insertable and over-voltage tolerant inputs 3-level inputs for selectable interface 3-level inputs for feedback divide selection with multiply ratios of(1-6, 8, 10, 12) Selectable HSTL, eHSTL, 1.8V/2.5V LVTTL, or LVEPECL input interface Selectable differential or single-ended inputs and six differential outputs PLL bypass for DC testing External differential feedback, internal loop filter Low Jitter: <75ps cycle-to-cycle Power-down mode Lock indicator Available in BGA and VFQFPN package * * * * * * * * The IDT5T2110 is a 2.5V PLL differential clock driver intended for high performance computing and data-communications applications. The IDT5T2110 has six differential outputs in six banks, including a dedicated differential feedback. The redundant input capability allows for a smooth change over to a secondary clock source when the primary clock source is absent. The feedback bank allows divide-by-functionality from 1 to 12 through the use of the DS[1:0] inputs. This provides the user with frequency multiplication 1 to 12 without using divided outputs for feedback. Each output bank also allows for a divide-by functionality of 2 or 4. The 5T2110 features a user-selectable, single-ended or differential input to six differential outputs. The differential clock driver also acts as a translator from a differential HSTL, eHSTL, 1.8V/2.5V LVTTL, LVEPECL, or single-ended 1.8V/2.5V LVTTL input to HSTL, eHSTL, or 1.8V/2.5V LVTTL outputs. Selectable interface is controlled by 3-level input signals that may be hard-wired to appropriate high-mid-low levels. The differential outputs can be synchronously enabled/disabled. Furthermore, when PE is held high, all the outputs are synchronized with the positive edge of the REF clock input. When PE is held low, all the outputs are synchronized with the negative edge of REF. FUNCTIONAL BLOCK DIAGRAM TxS 1sOE 1Q Divide Select OMODE 1Q 1F2:1 PD PE FS LOCK 2sOE 2Q Divide Select PLL_EN FB 3 FB/ VREF2 2F2:1 3 DS1:0 3sOE 3Q Divide Select PLL 3Q 0 REF0 REF0/ VREF0 2Q /N 3F2:1 4sOE 0 1 RxS 4Q Divide Select 4Q 1 4F2:1 REF1 REF1/ VREF1 REF_SEL Divide Select 5sOE 5Q 5Q 5F2:1 Divide Select QFB QFB The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE FBF2:1 AUGUST 2012 1 c 2012 Integrated Device Technology, Inc. DSC 5982/30 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE PIN CONFIGURATION 1 2 3 4 5 6 7 8 9 10 11 12 A VDD 1F2 1sOE 1Q 1Q GND GND 2Q 2Q 2sOE 2F2 VDDQ A B VDD VDD VDD NC 1F1 GND GND 2F1 NC VDDQ VDDQ 3F2 B OMODE VDD VDD VDD GND GND GND GND VDDQ VDDQ VDDQ 3sOE C C D REF_ SEL GND VDD VDD GND GND GND GND VDDQ VDDQ NC 3Q D E REF1 REF1 /VREF1 NC VDD GND GND GND GND VDDQ VDDQ 3F1 3Q E F REF0 REF0 /VREF0 VDD VDD GND GND GND GND VDDQ VDDQ VDDQ VDDQ F G FB FB /VREF2 VDD VDD GND GND GND GND VDDQ VDDQ VDDQ VDDQ G H PD PLL_ EN PE VDD GND GND GND GND VDDQ VDDQ 4F1 4Q H J RxS TxS VDD VDD GND GND GND GND VDDQ VDDQ NC 4Q J K LOCK VDD VDD VDD GND GND GND GND VDDQ VDDQ VDDQ 4sOE K L VDD VDD FS NC FBF1 GND GND 5F1 NC VDDQ VDDQ 4F2 L M DS1 DS0 FBF2 QFB QFB GND GND 5Q 5Q 5sOE 5F2 VDDQ M 1 2 3 4 5 6 7 8 9 10 11 12 BGA TOP VIEW 2 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE VDDQ 2sOE 2F 2 53 52 VDD 59 54 1F 1 60 VDDQ 1Q 61 55 1Q 62 2Q VDDQ 63 56 VDDQ 64 2Q 1sOE 65 57 1F 2 66 2F 1 VDD 67 58 OMODE 68 PIN CONFIGURATION REF_SEL 1 51 VDD VDD 2 50 3F 2 REF1 3 49 3sOE REF1/VREF1 4 48 VDDQ REF0 5 47 VDDQ REF0/VREF0 6 46 3Q FB 7 45 3Q FB/VREF2 8 44 3F 1 VDD 9 43 VDD PE 10 42 4F 1 PD 11 41 4Q PLL_EN 12 40 4Q VDD 13 39 VDDQ RxS 14 38 VDDQ TxS 15 37 4sOE LOCK 16 36 4F 2 VDD 17 35 VDD 30 31 32 33 34 5Q VDDQ VDDQ 5sOE 5F 2 QFB 29 25 QFB 5Q 24 28 23 VDDQ 5F 1 22 VDDQ 27 21 FBF2 VDD 20 FS FBF1 19 DS0 26 18 DS1 GND VFQFPN TOP VIEW 3 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK ABSOLUTE MAXIMUM RATINGS(1) Symbol Description INDUSTRIAL TEMPERATURE RANGE CAPACITANCE(TA = +25C, f = 1MHz, VIN = 0V) Max Unit VDDQ, VDD Power Supply Voltage(2) -0.5 to +3.6 V VI Input Voltage -0.5 to +3.6 V VO Output Voltage -0.5 to VDDQ +0.5 V VREF Reference Voltage(3) -0.5 to +3.6 V TJ Junction Temperature 150 C TSTG Storage Temperature -65 to +165 C Parameter Description Min. Typ. Max. Unit CIN Input Capacitance COUT Output Capacitance 2.5 3 3.5 pF -- 6.3 7 pF NOTE: 1. Capacitance applies to all inputs except RxS, TxS, nF[2:1], FBF[2:1],and DS[1:0]. NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDDQ and VDD internally operate independently. No power sequencing requirements need to be met. 3. Not to exceed 3.6V. RECOMMENDED OPERATING RANGE Symbol TA VDD(1) Description Ambient Operating Temperature Internal Power Supply Voltage HSTL Output Power Supply Voltage Extended HSTL and 1.8V LVTTL Output Power Supply Voltage 2.5V LVTTL Output Power Supply Voltage Termination Voltage VDDQ(1) VT Min. -40 2.3 1.4 1.65 Typ. +25 2.5 1.5 1.8 VDD VDDQ / 2 Max. +85 2.7 1.6 1.95 Unit C V V V V V NOTE: 1. All power supplies should operate in tandem. If VDD or VDDQ is at maximum, then VDDQ or VDD (respectively) should be at maximum, and vice-versa. PIN DESCRIPTION Symbol REF[1:0] REF[1:0]/ VREF[1:0] I/O I I Type Adjustable(1) Adjustable(1) FB I Adjustable(1) FB/VREF2 I Adjustable(1) Description Clock input. REF[1:0] is the "true" side of the differential clock input. If operating in single-ended mode, REF[1:0] is the clock input. Complementary clock input. REF[1:0]/VREF[1:0] is the "complementary" side of REF[1:0] if the input is in differential mode. If operating in single-ended mode, REF[1:0]/VREF[1:0] is left floating. For single-ended operation in differential mode, REF[1:0]/VREF[1:0] should be set to the desired toggle voltage for REF[1:0]: 2.5V LVTTL VREF = 1250mV (SSTL2 compatible) 1.8V LVTTL, eHSTL VREF = 900mV HSTL VREF = 750mV LVEPECL VREF = 1082mV Clock input. FB is the "true" side of the differential feedback clock input. If operating in single-ended mode, FB is the differential feedback clock input. Complementary feedback clock input. FB/VREF2 is the "complementary" side of FB if the input is in differential mode. If operating in singleended mode, FB/VREF2 is left floating. For single-ended operation in differential mode, FB/VREF2 should be set to the desired toggle voltage for FB: 2.5V LVTTL VREF = 1250mV (SSTL2 compatible) 1.8V LVTTL, eHSTL VREF = 900mV HSTL VREF = 750mV LVEPECL VREF = 1082mV NOTE: 1. Inputs are capable of translating the following interface standards. User can select between: Single-ended 2.5V LVTTL levels Single-ended 1.8V LVTTL levels or Differential 2.5V/1.8V LVTTL levels Differential HSTL and eHSTL levels Differential LVEPECL levels 4 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE PIN DESCRIPTION, CONTINUED Symbol REF_SEL nsOE I/O I I Type LVTTL(1) LVTTL(1) QFB QFB nQ nQ RxS TxS O O O O I I Adjustable(2) Adjustable(2) Adjustable(2) Adjustable(2) 3-Level(3) 3-Level(3) PE I LVTTL(1) nF[2:1] I LVTTL(1) Description Reference clock select. When LOW, selects REF0 and REF0/VREF0. When HIGH, selects REF1 and REF1/VREF1. Synchronous output enable. When nsOE is HIGH, nQ and nQ are synchronously stopped. OMODE selects whether the outputs are gated LOW/HIGH or tri-stated. When OMODE is HIGH, PE determines the level at which the outputs stop. When PE is LOW/HIGH, the nQ is stopped in a HIGH/LOW state, while the nQ is stopped at a LOW/HIGH state. When OMODE is LOW, the outputs are tristated. Set nsOE LOW for normal operation. Feedback clock output Complementary feedback clock output Clock outputs Complementary clock outputs Selects single-ended 2.5V LVTTL (HIGH), 1.8V LVTTL (MID) REF clock input or differential (LOW) REF clock input Sets the drive strength of the output drivers and feedback inputs to be 2.5V LVTTL (HIGH), 1.8V LVTTL (MID) or eHSTL/HSTL (LOW) compatible. Used in conjuction with VDDQ to set the interface levels. Selectable positive or negative edge control. When LOW/HIGH the outputs are synchronized with the negative/positive edge of the reference clock (has internal pull-up). Function select inputs for divide-by-2, divide-by-4, zero delay, or invert on each bank. (See Control Summary table.) FBF[2:1] I LVTTL(1) Function select inputs for divide-by-2, divide-by-4, zero delay, or invert on the feedback bank (See Control Summary table) FS I LVTTL(1) Selects appropriate oscillator circuit based on anticipated frequency range (See VCO Frequency Range Select table) DS[1:0] I 3-Level(3) 3-level inputs for feedback input divider selection (See Divide Selection table) I LVTTL(1) PLL enable/disable control. Set LOW for normal operation. When PLL_EN is HIGH, the PLL is disabled and REF[1:0] goes to all outputs. PD I LVTTL(1) LOCK O LVTTL OMODE I LVTTL(1) Power down control. When PD is LOW, the inputs are disabled and internal switching is stopped. OMODE selects whether the outputs are gated LOW/HIGH or tri-stated. When OMODE is HIGH, PE determines the level at which the outputs stop. When PE is LOW/ HIGH, the nQ and QFB are stopped in a HIGH/LOW state, while the nQ and QFB are stopped in a LOW/HIGH state. When OMODE is LOW, the outputs are tri-stated. Set PD HIGH for normal operation. PLL lock indication signal. HIGH indicates lock. LOW indicates that the PLL is not locked and outputs may not be synchronized to the inputs. The output will be 2.5V LVTTL. (For more information on application specific use of the LOCK pin, please see AN237.) Output disable control. Determines the outputs' disable state. Used in conjunction with nsOE and PD. (See Output Enable/Disable and Powerdown tables.) PLL_EN VDDQ PWR Power supply for output buffers. When using 2.5V LVTTL, VDDQ should be connected to VDD. VDD GND PWR PWR Power supply for phase locked loop, lock output, inputs, and other internal circuitry Ground NOTES: 1. Pins listed as LVTTL inputs will accept 2.5V signals under all conditions. If the output is operating at 1.8V or 1.5V, the LVTTL inputs will accept 1.8V LVTTL signals as well. 2. Outputs are user selectable to drive 2.5V, 1.8V LVTTL, eHSTL, or HSTL interface levels when used with the appropriate VDDQ voltage. 3. 3-level inputs are static inputs and must be tied to VDD or GND or left floating. These inputs are not hot-insertable or over voltage tolerant. OUTPUT ENABLE/DISABLE nsOE OMODE Output L X Normal Operation VCO FREQUENCY RANGE SELECT FS(1) Min. Max. Unit H L Tri-State LOW 50 125 MHz H H Gated(1) HIGH 100 250 MHz NOTE: 1. The level to be set on FS is determined by the nominal operating frequency of the VCO. The VCO frequency (FNOM) always appears at nQ and nQ outputs when they are operated in their undivided modes. The frequency appearing at the REF[1:0] and REF[1:0] /VREF[1:0] and FB and FB/VREF2 inputs will be FNOM when the QFB and QFB are undivided and DS[1:0] = MM. The frequency of REF[1:0] and REF[1:0] /VREF[1:0] and FB and FB/VREF2 inputs will be FNOM/2 or FNOM/4 when the part is configured for frequency multiplication by using a divided QFB and QFB and setting DS[1:0] = MM. Using the DS[1:0] inputs allows a different method for frequency multiplication (see Divide Selection table). NOTE: 1. PE determines the level at which the outputs stop. When PE is LOW/HIGH, the nQ is stopped in a HIGH/LOW state while the nQ is stopped at a LOW/HIGH state. POWERDOWN PD OMODE Output H X Normal Operation L L Tri-State L H Gated(1) NOTE: 1. PE determines the level at which the outputs stop. When PE is LOW/HIGH, the nQ and QFB are stopped in a HIGH/LOW state, while the nQ and QFB are stopped in a LOW/HIGH state. 5 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE EXTERNAL DIFFERENTIAL FEEDBACK By providing a dedicated external differential feedback, the IDT5T2110 gives users flexibility with regard to divide selection. The FB and FB/ VREF2 signals are compared with the input REF[1:0] and REF[1:0]/VREF[1:0] signals at the phase detector in order to drive the VCO. Phase differences cause the VCO of the PLL to adjust upwards or downwards accordingly. An internal loop filter moderates the response of the VCO to the phase detector. The loop filter transfer function has been chosen to provide minimal jitter (or frequency variation) while still providing accurate responses to input frequency changes. DIVIDE SELECTION TABLE DS [1:0] Divide-by-n Permitted Output Divide-by-n connected to FB and FB/VREF2(1) LL 2 1, 2 LM 3 1 LH 4 1, 2 ML 5 1, 2 MM 1 1, 2, 4 MH 6 1, 2 HL 8 1 HM 10 1 HH 12 1 NOTE: 1. Permissible output division ratios connected to FB and FB/VREF2. The frequencies of the REF[1:0] and REF[1:0]/VREF[1:0] inputs will be FNOM/N when the parts are configured for frequency multiplication by using an undivided output for FB and FB/VREF2 and setting DS[1:0] to N (N = 1-6, 8, 10, 12). CONTROL SUMMARY TABLE FOR ALL OUTPUTS nF2/FBF2 nF1/FBF1 Output Skew L L Divide by 2 L H Zero Delay H L Inverted H H Divide by 4 6 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE INPUT/OUTPUT SELECTION(1) Input Output Input Output 2.5V LVTTL SE 1.8V LVTTL SE 2.5V LVTTL 2.5V LVTTL SE 1.8V LVTTL SE eHSTL 2.5V LVTTL DSE 1.8V LVTTL DSE 2.5V LVTTL DSE 1.8V LVTTL DSE LVEPECL DSE eHSTL DSE LVEPECL DSE eHSTL DSE HSTL DSE 2.5V LVTTL DIF HSTL DSE 2.5V LVTTL DIF 1.8V LVTTL DIF LVEPECL DIF 1.8V LVTTL DIF LVEPECL DIF eHSTL DIF HSTL DIF eHSTL DIF HSTL DIF 2.5V LVTTL SE 1.8V LVTTL SE 2.5V LVTTL SE 1.8V LVTTL SE 1.8V LVTTL 2.5V LVTTL DSE 1.8V LVTTL DSE 2.5V LVTTL DSE 1.8V LVTTL DSE LVEPECL DSE eHSTL DSE LVEPECL DSE eHSTL DSE HSTL DSE 2.5V LVTTL DIF HSTL DSE 2.5V LVTTL DIF 1.8V LVTTL DIF LVEPECL DIF eHSTL DIF 1.8V LVTTL DIF LVEPECL DIF HSTL eHSTL DIF HSTL DIF HSTL DIF NOTE: 1. The INPUT/OUTPUT SELECTION Table describes the total possible combinations of input and output interfaces. Single-Ended (SE) inputs in a single-ended mode require the REF[1:0]/VREF[1:0] and FB/VREF2 pins to be left floating. Differential Single-Ended (DSE) is for single-ended operation in differential mode, requiring VREF[1:0] and VREF2. Differential (DIF) inputs are used only in differential mode. DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Symbol VIHH VIMM VILL Parameter Input HIGH Voltage Level(1) Input MID Voltage Level(1) Input LOW Voltage Level(1) I3 3-Level Input DC Current (RxS, TxS, DS[1:0]) Input Pull-Up Current (PE) IPU Test Conditions 3-Level Inputs Only 3-Level Inputs Only 3-Level Inputs Only HIGH Level VIN = VDD VIN = VDD/2 MID Level VIN = GND LOW Level VDD = Max., VIN = GND Min. VDD - 0.4 VDD/2 - 0.2 -- -- -50 -200 -100 Max -- VDD/2 + 0.2 0.4 200 +50 -- -- Unit V V V A A NOTE: 1. These inputs are normally wired to VDD, GND, or left floating. Internal termination resistors bias unconnected inputs to VDD/2. If these inputs are switched dynamically after powerup, the function and timing of the outputs may be glitched, and the PLL may require additional tLOCK time before all datasheet limits are achieved. 7 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR HSTL(1) Symbol Parameter Input Characteristics IIH Input HIGH Current IIL Input LOW Current VIK Clamp Diode Voltage VIN DC Input Voltage VDIF DC Differential Voltage(2,8) VCM DC Common Mode Input Voltage(3,8) VIH DC Input HIGH(4,5,8) VIL DC Input LOW(4,6,8) Single-Ended Reference Voltage(4,8) VREF Output Characteristics VOH Output HIGH Voltage VOL Output LOW Voltage VOX Qn/Qn and FB/FB Output Crossing Point Test Conditions VDD = 2.7V VI = VDDQ/GND VDD = 2.7V VI = GND/VDDQ VDD = 2.3V, IIN = -18mA IOH = -8mA IOH = -100A IOL = 8mA IOL = 100A Min. Typ.(7) Max Unit -- -- -- - 0.3 0.2 680 VREF + 100 -- -- -- -- - 0.7 A 750 5 5 - 1.2 +3.6 -- 900 -- VREF - 100 -- VDDQ/2 -- -- 0.4 0.1 VDDQ/2 + 150 VDDQ - 0.4 VDDQ - 0.1 -- -- VDDQ/2 - 150 750 V V V mV mV mV mV V V mV NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. VDIF specifies the minimum input differential voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. Differential mode only. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching to a new state. 3. VCM specifies the maximum allowable range of (VTR + VCP) /2. Differential mode only. 4. For single-ended operation, in differential mode, REF[1:0]/VREF[1:0] is tied to the DC voltage VREF[1:0]. 5. Voltage required to maintain a logic HIGH, single-ended operation in differential mode. 6. Voltage required to maintain a logic LOW, single-ended operation in differential mode. 7. Typical values are at VDD = 2.5V, VDDQ = 1.5V, +25C ambient. 8. The reference clock input is capable of HSTL, eHSTL, LVEPECL, 1.8V or 2.5V LVTTL operation independent of the device output. (See Input/Output Selection table.) 8 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS FOR HSTL OUTPUTS(1) Symbol IDDQ Parameter Quiescent VDD Power Supply Current(3) IDDQQ Quiescent VDDQ Power Supply Current(3) IDDPD IDDD ITOT Power Down Current Dynamic VDD Power Supply Current per Output Dynamic VDDQ Power Supply Current per Output Total Power VDD Supply Current(4) ITOTQ Total Power VDDQ Supply Current(4) IDDDQ Test Conditions(2) VDDQ = Max., REF = LOW, PD = HIGH, nSOE = LOW, PLL_EN = HIGH, DS[1:0] = MM, nF[2:1] = LH, FBF[2:1] = LH, Outputs enabled, All outputs unloaded VDDQ = Max., REF = LOW, PD = HIGH, nSOE = LOW, PLL_EN = HIGH, DS[1:0] = MM, nF[2:1] = LH, FBF[2:1] = LH, Outputs enabled, All outputs unloaded VDD = Max., PD = LOW, nSOE = LOW, PLL_EN = HIGH VDD = Max., VDDQ = Max., CL = 0pF Typ. 15 Max 25 Unit mA 0.7 50 A 0.8 13 3 20 mA A/MHz VDD = Max., VDDQ = Max., CL = 0pF 16 25 A/MHz VDDQ = 1.5V, FVCO = 100MHz, CL = 15pF VDDQ = 1.5V, FVCO = 250MHz, CL = 15pF VDDQ = 1.5V, FVCO = 100MHz, CL = 15pF VDDQ = 1.5V, FVCO = 250MHz, CL = 15pF 35 55 45 80 55 85 70 120 mA mA NOTES: 1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations. 2. The termination resistors are excluded from these measurements. 3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH. 4. FS = HIGH. DIFFERENTIAL INPUT AC TEST CONDITIONS FOR HSTL Symbol Parameter VDIF Input Signal Swing(1) VX Differential Input Signal Crossing Point VTHI Input Timing Measurement Reference Level(3) tR, tF Input Signal Edge Rate (2) (4) Value Units 1 V 750 mV Crossing Point V 1 V/ns NOTES: 1. The 1V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A 750mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 1V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. 9 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR eHSTL(1) Symbol Parameter Input Characteristics IIH Input HIGH Current IIL Input LOW Current VIK Clamp Diode Voltage VIN DC Input Voltage VDIF DC Differential Voltage(2,8) VCM DC Common Mode Input Voltage(3,8) VIH DC Input HIGH(4,5,8) VIL DC Input LOW(4,6,8) Single-Ended Reference Voltage(4,8) VREF Output Characteristics VOH Output HIGH Voltage VOL Output LOW Voltage VOX Qn/Qn and FB/FB Output Crossing Point Test Conditions VDD = 2.7V VI = VDDQ/GND VDD = 2.7V VI = GND/VDDQ VDD = 2.3V, IIN = -18mA IOH = -8mA IOH = -100A IOL = 8mA IOL = 100A Min. Typ.(7) Max Unit -- -- -- - 0.3 0.2 800 VREF + 100 -- -- -- -- - 0.7 A 900 5 5 - 1.2 +3.6 -- 1000 -- VREF - 100 -- V V V mV mV mV mV VDDQ/2 -- -- 0.4 0.1 VDDQ/2 + 150 V V V V mV VDDQ - 0.4 VDDQ - 0.1 -- -- VDDQ/2 - 150 900 NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. VDIF specifies the minimum input differential voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. Differential mode only. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching to a new state. 3. VCM specifies the maximum allowable range of (VTR + VCP) /2. Differential mode only. 4. For single-ended operation, in a differential mode, REF[1:0]/VREF[1:0] is tied to the DC voltage VREF[1:0]. 5. Voltage required to maintain a logic HIGH, single-ended operation in differential mode. 6. Voltage required to maintain a logic LOW, single-ended operation in differential mode. 7. Typical values are at VDD = 2.5V, VDDQ = 1.8V, +25C ambient. 8. The reference clock input is capable of HSTL, eHSTL, LVEPECL, 1.8V or 2.5V LVTTL operation independent of the device output. (See Input/Output Selection table.) POWER SUPPLY CHARACTERISTICS FOR eHSTL OUTPUTS(1) Symbol IDDQ Parameter Quiescent VDD Power Supply Current(3) IDDQQ Quiescent VDDQ Power Supply Current(3) IDDPD IDDD ITOT Power Down Current Dynamic VDD Power Supply Current per Output Dynamic VDDQ Power Supply Current per Output Total Power VDD Supply Current(4) ITOTQ Total Power VDDQ Supply Current(4) IDDDQ Test Conditions(2) VDDQ = Max., REF = LOW, PD = HIGH, nSOE = LOW, PLL_EN = HIGH, DS[1:0] = MM, nF[2:1] = LH, FBF[2:1] = LH, Outputs enabled, All outputs unloaded VDDQ = Max., REF = LOW, PD = HIGH, nSOE = LOW, PLL_EN = HIGH, DS[1:0] = MM, nF[2:1] = LH, FBF[2:1] = LH, Outputs enabled, All outputs unloaded VDD = Max., PD = LOW, nSOE = LOW, PLL_EN = HIGH VDD = Max., VDDQ = Max., CL = 0pF Typ. 15 Max 25 Unit mA 1.7 50 A 0.8 13 3 20 mA A/MHz VDD = Max., VDDQ = Max., CL = 0pF 20 30 A/MHz VDDQ = 1.8V, FVCO = 100MHz, CL = 15pF VDDQ = 1.8V, FVCO = 250MHz, CL = 15pF VDDQ = 1.8V, FVCO = 100MHz, CL = 15pF VDDQ = 1.8V, FVCO = 250MHz, CL = 15pF 35 55 50 115 55 85 75 175 mA NOTES: 1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations. 2. The termination resistors are excluded from these measurements. 3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH. 4. FS = HIGH 10 mA IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE DIFFERENTIAL INPUT AC TEST CONDITIONS FOR eHSTL Symbol Parameter VDIF Input Signal Swing(1) VX Differential Input Signal Crossing Point VTHI Input Timing Measurement Reference Level(3) tR, tF Input Signal Edge Rate (2) (4) Value Units 1 V 900 mV Crossing Point V 1 V/ns NOTES: 1. The 1V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A 900mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 1V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR LVEPECL(1) Symbol Parameter Input Characteristics IIH Input HIGH Current IIL Input LOW Current VIK Clamp Diode Voltage VIN DC Input Voltage VCM DC Common Mode Input Voltage(3,5) VREF Single-Ended Reference Voltage(4,5) VIH DC Input HIGH VIL DC Input LOW Test Conditions VDD = 2.7V VI = VDDQ/GND VDD = 2.7V VI = GND/VDDQ VDD = 2.3V, IIN = -18mA Min. Typ.(2) Max Unit -- -- -- - 0.3 915 -- 1275 555 -- -- - 0.7 -- 1082 1082 -- -- 5 5 - 1.2 3.6 1248 -- 1620 875 A V V mV mV mV mV NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. Typical values are at VDD = 2.5V, +25C ambient. 3. VCM specifies the maximum allowable range of (VTR + VCP) /2. Differential mode only. 4. For single-ended operation while in differential mode, REF[1:0]/VREF[1:0] is tied to the DC voltage VREF[1:0]. 5. The reference clock input is capable of HSTL, eHSTL, LVEPECL, 1.8V or 2.5V LVTTL operation independent of the device output. (See Input/Output Selection table.) 11 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE DIFFERENTIAL INPUT AC TEST CONDITIONS FOR LVEPECL Symbol Parameter Value Units VDIF Input Signal Swing (1) 732 mV VX Differential Input Signal Crossing Point(2) 1082 mV VTHI Input Timing Measurement Reference Level(3) tR, tF Input Signal Edge Rate(4) Crossing Point V 1 V/ns NOTES: 1. The 732mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A 1082mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 1V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR 2.5V LVTTL(1) Symbol Parameter Input Characteristics IIH Input HIGH Current IIL Input LOW Current VIK Clamp Diode Voltage DC Input Voltage VIN Single-Ended Inputs(2) VIH DC Input HIGH DC Input LOW VIL Differential Inputs VDIF DC Differential Voltage(3,9) VCM DC Common Mode Input Voltage(4,9) VIH DC Input HIGH(5,6,9) VIL DC Input LOW(5,7,9) Single-Ended Reference Voltage(5,9) VREF Output Characteristics VOH Output HIGH Voltage VOL Output LOW Voltage Test Conditions VDD = 2.7V VI = VDDQ/GND VDD = 2.7V VI = GND/VDDQ VDD = 2.3V, IIN = -18mA IOH = -12mA IOH = -100A IOL = 12mA IOL = 100A Min. Typ.(8) Max Unit -- -- -- - 0.3 -- -- - 0.7 5 5 - 1.2 +3.6 A 1.7 -- -- 0.7 V V 0.2 1150 VREF + 100 -- -- -- 1350 -- VREF - 100 -- V mV mV mV mV -- -- 0.4 0.1 V V V V VDDQ - 0.4 VDDQ - 0.1 -- -- 1250 1250 V V NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. For 2.5V LVTTL single-ended operation, the RxS pin is tied HIGH and REF[1:0]/VREF[1:0] is left floating. If TxS is HIGH, FB/VREF2 should be left floating. 3. VDIF specifies the minimum input differential voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. Differential mode only. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching to a new state. 4. VCM specifies the maximum allowable range of (VTR + VCP) /2. Differential mode only. 5. For single-ended operation, in differential mode, REF[1:0]/VREF[1:0] is tied to the DC voltage VREF[1:0]. 6. Voltage required to maintain a logic HIGH, single-ended operation in differential mode. 7. Voltage required to maintain a logic LOW, single-ended operation in differential mode. 8. Typical values are at VDD = 2.5V, VDDQ = VDD, +25C ambient. 9. The reference clock input is capable of HSTL, eHSTL, LVEPECL, 1.8V or 2.5V LVTTL operation independent of the device output. (See Input/Output Selection table.) 12 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS FOR 2.5V LVTTL OUTPUTS(1) Symbol IDDQ Parameter Quiescent VDD Power Supply Current(3) IDDQQ Quiescent VDDQ Power Supply Current(3) IDDPD IDDD ITOT Power Down Current Dynamic VDD Power Supply Current per Output Dynamic VDDQ Power Supply Current per Output Total Power VDD Supply Current(4) ITOTQ Total Power VDDQ Supply Current(4) IDDDQ Test Conditions(2) VDDQ = Max., REF = LOW, PD = HIGH, nSOE = LOW, PLL_EN = HIGH, DS[1:0] = MM, nF[2:1] = LH, FBF[2:1] = LH, Outputs enabled, All outputs unloaded VDDQ = Max., REF = LOW, PD = HIGH, nSOE = LOW, PLL_EN = HIGH, DS[1:0] = MM, nF[2:1] = LH, FBF[2:1] = LH, Outputs enabled, All outputs unloaded VDD = Max., PD = LOW, nSOE = LOW, PLL_EN = HIGH VDD = Max., VDDQ = Max., CL = 0pF Typ. 15 Max 25 Unit mA 12 50 A 0.5 15 3 25 mA A/MHz VDD = Max., VDDQ = Max., CL = 0pF 30 40 A/MHz VDDQ = 2.5V., FVCO = 100MHz, CL = 15pF VDDQ = 2.5V., FVCO = 250MHz, CL = 15pF VDDQ = 2.5V., FVCO = 100MHz, CL = 15pF VDDQ = 2.5V., FVCO = 250MHz, CL = 15pF 40 60 80 200 60 90 120 300 mA mA NOTES: 1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations. 2. The termination resistors are excluded from these measurements. 3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH. 4. FS = HIGH. DIFFERENTIAL INPUT AC TEST CONDITIONS FOR 2.5V LVTTL Symbol Parameter VDIF Input Signal Swing(1) VX Differential Input Signal Crossing Point VTHI Input Timing Measurement Reference Level(3) tR, tF Input Signal Edge Rate(4) (2) Value Units VDD V VDD/2 V Crossing Point V 2.5 V/ns NOTES: 1. A nominal 2.5V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A nominal 1.25V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 2.5V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. SINGLE-ENDED INPUT AC TEST CONDITIONS FOR 2.5V LVTTL Symbol Parameter Value Units VIH Input HIGH Voltage VDD V VIL Input LOW Voltage 0 V VTHI Input Timing Measurement Reference Level tR, tF Input Signal Edge Rate(2) (1) VDD/2 V 2 V/ns NOTES: 1. A nominal 1.25V timing measurement reference level is specified to allow constant, repeatable results in an automatic test equipment (ATE) environment. 2. The input signal edge rate of 2V/ns or greater is to be maintained in the 10% to 90% range of the input waveform. 13 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR 1.8V LVTTL(1) Symbol Parameter Input Characteristics IIH Input HIGH Current IIL Input LOW Current VIK Clamp Diode Voltage DC Input Voltage VIN Single-Ended Inputs(2) VIH DC Input HIGH DC Input LOW VIL Differential Inputs VDIF DC Differential Voltage(3,9) VCM DC Common Mode Input Voltage(4,9) VIH DC Input HIGH(5,6,9) VIL DC Input LOW(5,7,9) Single-Ended Reference Voltage(5,9) VREF Output Characteristics VOH Output HIGH Voltage VOL Output LOW Voltage Test Conditions VDD = 2.7V VI = VDDQ/GND VDD = 2.7V VI = GND/VDDQ VDD = 2.3V, IIN = -18mA Min. Typ.(8) Max Unit -- -- -- - 0.3 -- -- - 0.7 5 5 - 1.2 VDDQ + 0.3 A -- 0.683(11) V V -- 975 -- VREF - 100 -- V mV mV mV mV -- -- 0.4 0.1 V V V V 1.073(10) -- 0.2 825 VREF + 100 -- -- IOH = -6mA IOH = -100A IOL = 6mA IOL = 100A VDDQ - 0.4 VDDQ - 0.1 -- -- 900 900 V V NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. For 1.8V LVTTL single-ended operation, the RxS pin is MID and REF[1:0]/VREF[1:0] is left floating. If TxS is MID, FB/VREF2 should be left floating. 3. VDIF specifies the minimum input differential voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. Differential mode only. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching to a new state. 4. VCM specifies the maximum allowable range of (VTR + VCP) /2. Differential mode only. 5. For single-ended operation in differential mode, REF[1:0]/VREF[1:0] is tied to the DC voltage VREF[1:0]. The input is guaranteed to toggle within 200mV of VREF[1:0] when VREF[1:0] is constrained within +600mV and VDDI-600mV, where VDDI is the nominal 1.8V power supply of the device driving the REF[1:0] input. To guarantee switching in voltage range specified in the JEDEC 1.8V LVTTL interface specification, VREF[1:0] must be maintained at 900mV with appropriate tolerances. 6. Voltage required to maintain a logic HIGH, single-ended operation in differential mode. 7. Voltage required to maintain a logic LOW, single-ended operation in differential mode. 8. Typical values are at VDD = 2.5V, VDDQ = 1.8V, +25C ambient. 9. The reference clock input is capable of HSTL, eHSTL, LVEPECL, 1.8V or 2.5V LVTTL operation independent of the device output. (See Input/Output Selection table.) 10. This value is the worst case minimum VIH over the specification range of the 1.8V power supply. The 1.8V LVTTL specification is VIH = 0.65 * VDD where VDD is 1.8V 0.15V. However, the LVTTL translator is supplied by a 2.5V nominal supply on this part. To ensure compliance with the specification, the translator was designed to accept the calculated worst case value ( VIH = 0.65 * [1.8 - 0.15V]) rather than reference against a nominal 1.8V supply. 11. This value is the worst case maximum VIL over the specification range of the 1.8V power supply. The 1.8V LVTTL specification is VIL = 0.35 * VDD where VDD is 1.8V 0.15V. However, the LVTTL translator is supplied by a 2.5V nominal supply on this part. To ensure compliance with the specification, the translator was designed to accept the calculated worst case value ( VIL = 0.35 * [1.8 + 0.15V]) rather than reference against a nominal 1.8V supply. 14 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS FOR 1.8V LVTTL OUTPUTS(1) Symbol IDDQ Parameter Quiescent VDD Power Supply Current(3) IDDQQ Quiescent VDDQ Power Supply Current(3) IDDPD IDDD ITOT Power Down Current Dynamic VDD Power Supply Current per Output Dynamic VDDQ Power Supply Current per Output Total Power VDD Supply Current(4) ITOTQ Total Power VDDQ Supply Current(4) IDDDQ Test Conditions(2) VDDQ = Max., REF = LOW, PD = HIGH, nSOE = LOW, PLL_EN = HIGH, DS[1:0] = MM, nF[2:1] = LH, FBF[2:1] = LH, Outputs enabled, All outputs unloaded VDDQ = Max., REF = LOW, PD = HIGH, nSOE = LOW, PLL_EN = HIGH, DS[1:0] = MM, nF[2:1] = LH, FBF[2:1] = LH, Outputs enabled, All outputs unloaded VDD = Max., PD = LOW, nSOE = LOW, PLL_EN = HIGH VDD = Max., VDDQ = Max., CL = 0pF Typ. 15 Max 25 Unit mA 1.5 50 A 0.5 16 3 25 mA A/MHz VDD = Max., VDDQ = Max., CL = 0pF 22 30 A/MHz VDDQ = 1.8V., FVCO = 100MHz, CL = 15pF VDDQ = 1.8V., FVCO = 250MHz, CL = 15pF VDDQ = 1.8V., FVCO = 100MHz, CL = 15pF VDDQ = 1.8V., FVCO = 250MHz, CL = 15pF 40 70 55 135 60 105 85 205 mA mA NOTES: 1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations. 2. The termination resistors are excluded from these measurements. 3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH. 4. FS = HIGH. DIFFERENTIAL INPUT AC TEST CONDITIONS FOR 1.8V LVTTL Symbol Parameter Value Units VDIF Input Signal Swing (1) VDDI V VX Differential Input Signal Crossing Point(2) VDDI/2 mV VTHI Input Timing Measurement Reference Level(3) tR, tF Input Signal Edge Rate(4) Crossing Point V 1.8 V/ns NOTES: 1. VDDI is the nominal 1.8V supply (1.8V 0.15V) of the part or source driving the input. A nominal 1.8V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A nominal 900mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 1.8V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. SINGLE-ENDED INPUT AC TEST CONDITIONS FOR 1.8V LVTTL Symbol Parameter Value VIH Input HIGH Voltage VIL Input LOW Voltage VTHI Input Timing Measurement Reference Level(2) tR, tF Input Signal Edge Rate(3) (1) VDDI V 0 V VDDI/2 mV 2 V/ns NOTES: 1. VDDI is the nominal 1.8V supply (1.8V 0.15V) of the part or source driving the input. 2. A nominal 900mV timing measurement reference level is specified to allow constant, repeatable results in an automatic test equipment (ATE) environment. 3. The input signal edge rate of 2V/ns or greater is to be maintained in the 10% to 90% range of the input waveform. 15 Units IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE AC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Symbol FNOM tRPW tFPW tSK(O) tSK1() tSK2() tSK1(INV) tSK2(INV) tSK(PR) t() tODCV tORISE tOFALL tL tL() tL(PD) tL(REFSEL1) tL(REFSEL2) tJIT(CC) Parameter VCO Frequency Range Reference Clock Pulse Width HIGH or LOW Feedback Input Pulse Width HIGH or LOW Output Skew (Rise-Rise, Fall-Fall, Nominal)(1,2) Multiple Frequency Skew (Rise-Rise, Fall-Fall, Nominal-Divided, Divided-Divided)(1,2,3) Multiple Frequency Skew (Rise-Fall, Nominal-Divided, Divided-Divided)(1,2,3) Inverting Skew (Nominal-Inverted)(1,2) Inverting Skew (Rise-Rise, Fall-Fall, Rise-Fall, Inverted-Divided)(1,2,3) Process Skew(1,2,4) REF Input to FB Static Phase Offset(5) Output Duty Cycle Variation from 50%(11,12) 1.8V LVTTL 2.5V LVTTL Output Rise Time(6) HSTL / eHSTL / 1.8V LVTTL 2.5V LVTTL Output Fall Time(6) HSTL / eHSTL / 1.8V LVTTL 2.5V LVTTL Power-up PLL Lock Time(7) PLL Lock Time After Input Frequency Change(7) PLL Lock Time After Asserting PD Pin(7) PLL Lock Time After Change in REF_SEL(7,9) PLL Lock Time After Change in REF_SEL (REF1 and REF0 are different frequency)(7) Cycle-to-Cycle Output Jitter (peak-to-peak)(2,8) Min. Typ. Max Unit see VCO Frequency Range Select Table 1 -- -- ns 1 -- -- ns -- -- 100 ps -- -- 100 ps -- -- 300 ps -- -- 300 ps -- -- 300 ps -- -- 300 ps -100 -- 100 ps -375 -- 375 ps -275 -- 275 -- -- 1.2 ns -- -- 1 -- -- 1.2 ns -- -- 1 -- -- 1 ms -- -- 1 ms -- -- 1 ms -- -- 100 s -- -- 1 ms -- 50 75 ps tJIT(PER) Period Jitter (peak-to-peak)(2,8) -- -- 75 ps tJIT(HP) Half Period Jitter (peak-to-peak)(2,8,10) -- -- 125 ps -- VDDQ/2 - 150 -- 100 VDDQ/2 + 150 ps mV tJIT(DUTY) VOX Duty Cycle Jitter (peak-to-peak)(2,8) HSTL and eHSTL Differential True and Complementary Output Crossing Voltage Level VDDQ/2 NOTES: 1. Skew is the time between the earliest and latest output transition among all outputs when all outputs are loaded with the specified load. 2. For differential LVTTL outputs, the measurement is made at VDDQ/2, where the true outputs are only compared with other true outputs and the complementary outputs are only compared to other complementary outputs. For differential HSTL/eHSTL outputs, the measurement is made at the crossing point (VOX) of the true and complementary signals. 3. There are three classes of outputs: nominal (zero delay), inverted, and divided (divide-by-2 or divide-by-4 mode). 4. tSK(PR) is the output to corresponding output skew between any two devices operating under the same conditions (VDD and VDDQ, ambient temperature, air flow, etc.). 5. t() is measured with REF and FB the same type of input, the same rise and fall times. For TxS/RxS = MID or HIGH, the measurement is taken from VTHI on REF to VTHI on FB. For TxS/RxS = LOW, the measurement is taken from the crosspoint of REF/REF to the crosspoint of FB/FB. All outputs are set to zero delay, FB input divider is set to divide-by-one, and FS = HIGH. 6. Output rise and fall times are measured between 20% to 80% of the actual output voltage swing. 7. tL, tL(), tL(REFSEL1), tL(REFSEL2), and tL(PD) are the times that are required before the synchronization is achieved. These specifications are valid only after VDD/VDDQ is stable and within the normal operating limits. These parameters are measured from the application of a new signal at REF or FB, or after PD is (re)asserted until t() is within specified limits. 8. The jitter parameters are measured with all outputs selected for zero delay, FB input divider is set to divide-by-one, and FS = HIGH. 9. Both REF inputs must be the same frequency, but up to 180 out of phase. 10. For HSTL/eHSTL outputs only. 11. For LVTTL outputs only. 12. tODCV is measured with all outputs selected for zero delay. 16 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE AC DIFFERENTIAL INPUT SPECIFICATIONS(1) Symbol tW Parameter Reference/Feedback Input Clock Pulse Width HIGH or LOW (HSTL/eHSTL outputs)(2) Reference/Feedback Input Clock Pulse Width HIGH or LOW (2.5V / 1.8V LVTTL outputs)(2) HSTL/eHSTL/1.8V LVTTL/2.5V LVTTL VDIF AC Differential Voltage(3) VIH AC Input HIGH VIL LVEPECL (4,5) AC Input LOW (4,6) Min. 1 1 Typ. -- -- Max -- -- Unit ns 400 -- -- mV Vx + 200 -- -- mV -- -- Vx - 200 mV -- mV VDIF AC Differential Voltage(3) 400 -- VIH AC Input HIGH 1275 -- -- mV VIL AC Input LOW(4) -- -- 875 mV (4) NOTES: 1. For differential input mode, RxS is tied to GND. 2. Both differential input signals should not be driven to the same level simultaneously. The input will not change state until the inputs have crossed and the voltage range defined by VDIF has been met or exceeded. 3. Differential mode only. VDIF specifies the minimum input voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. The AC differential voltage must be achieved to guarantee switching to a new state. 4. For single-ended operation, REF[1:0]/VREF[1:0] is tied to the DC voltage VREF[1:0]. Refer to each input interface's DC specification for the correct VREF[1:0] range. 5. Voltage required to switch to a logic HIGH, single-ended operation only. 6. Voltage required to switch to a logic LOW, single-ended operation only. 17 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE AC TIMING DIAGRAM(1) tRPWL REF tRPWH REF tFPWH tFPWL FB FB tODCV tODCV Q Q tSK(O) tSK(O) OTHER Q OTHER Q tSK1(INV) tSK1(INV) INVERTED Q INVERTED Q tSK2( ), tSK2(INV) tSK2(INV) tSK2( ) tSK1( ) Q DIVIDED BY 2 Q DIVIDED BY 2 tSK1( ), tSK2(INV) Q DIVIDED BY 4 Q DIVIDED BY 4 NOTE: 1. The AC TIMING DIAGRAM applies to PE = VDD. For PE = GND, the negative edge of FB aligns with the negative edge of REF[1:0], divided outputs change on the negative edge of REF[1:0], and the positive edges of the divide-by-2 and divide-by-4 signals align. 18 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE JITTER AND OFFSET TIMING WAVEFORMS nQ, QFB nQ, QFB tcycle n tcycle n + 1 tjit(cc) = tcycle n tcycle n+1 Cycle-to-Cycle jitter REF[1:0] REF[1:0] FB FB t(O)n + 1 t(O)n n=N 1 t(O) = t(O)n N Static Phase Offset NOTE: 1. Diagram for PE = H and TxS/RxS = L. 19 (N is a large number of samples) IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE JITTER AND OFFSET TIMING WAVEFORMS nQ, QFB nQ, QFB tW(MIN) tW(MAX) tJIT(DUTY) = tW(MAX) - tW(MIN) Duty-Cycle Jitter nQ, QFB nQ, QFB tcycle n nQ, QFB nQ, QFB 1 fo tjit(per) = tcycle n 1 fo Period jitter nQ, QFB nQ, QFB thalf period n+1 thalf period n nQ, QFB nQ, QFB 1 fo tjit(hper) = thalf period n Half-Period jitter 20 1 2*f o IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND CONDITIONS VDDI R1 VIN 3 inch, ~50 Transmission Line VDD VDDQ R2 VDDI REF[1:0] D.U.T. Pulse Generator R1 VIN REF[1:0] 3 inch, ~50 Transmission Line R2 Test Circuit for Differential Input(1) DIFFERENTIAL INPUT TEST CONDITIONS Symbol VDD = 2.5V 0.2V Unit R1 100 R2 100 VDDI VCM*2 V HSTL: Crossing of REF[1:0] and REF[1:0] eHSTL: Crossing of REF[1:0] and REF[1:0] VTHI LVEPECL: Crossing of REF[1:0] and REF[1:0] V 1.8V LVTTL: VDDI/2 2.5V LVTTL: VDD/2 NOTE: 1. This input configuration is used for all input interfaces. For single-ended testing, the REF[1:0] must be left floating. For testing single-ended in differential input mode, the VIN should be floating. 21 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE VDDQ VDD VDDQ REF[1:0] R1 VDDQ VDDQ R1 nQ CL D.U.T. R1 R2 VDDQ VDD R2 CL REF[1:0] nQ FB QFB FB QFB VDDQ QFB D.U.T. R2 CL R1 FB QFB FB CL R2 SW1 SW1 Test Circuit for Differential Feedback Test Circuit for Differential Outputs DIFFERENTIAL FEEDBACK TEST CONDITIONS DIFFERENTIAL OUTPUT TEST CONDITIONS Symbol VDD = 2.5V 0.2V Symbol Unit VDD = 2.5V 0.2V Unit VDDQ = Interface Specified VDDQ = Interface Specified CL 15 pF CL 15 pF R1 100 R1 100 R2 100 R2 100 VOX HSTL: Crossing of nQ and nQ V VOX HSTL: Crossing of QFB and QFB V V VTHO 1.8V LVTTL: VDDQ/2 Open SW1 TxS = MID or HIGH Open TxS = LOW Closed eHSTL: Crossing of QFB and QFB eHSTL: Crossing of nQ and nQ VTHO 1.8V LVTTL: VDDQ/2 SW1 TxS = MID or HIGH 2.5V LVTTL: VDDQ/2 2.5V LVTTL: VDDQ/2 TxS = LOW V Closed 22 IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK RECOMMENDED LANDING PATTERN NL 68 pin NOTE: All dimensions are in millimeters. 23 INDUSTRIAL TEMPERATURE RANGE IDT5T2110 2.5V ZERO DELAY PLL DIFFERENTIAL CLOCK DRIVER TERACLOCK INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDT XXXXX Device Type XX Package X Package I -40C to +85C (Industrial) BB BBG NL NLG 5T2110 CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 Plastic Ball Grid Array PBGA - Green Thermally Enhanced Plastic Very Fine Pitch Quad Flat No Lead Package VFQFPN - Green 2.5V Zero Delay PLL Differential Clock Driver Teraclock for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 24 for Tech Support: clockhelp@idt.com