+VS
A0
A1
A2
SCL
SDA
O.S.
GND
8
7
6
53
1
2
4
LM75
Address
(Set as desired) To Processor
Interrupt Line
Interface
100 nF (typ) unless mounted
close to processor
O.S. set to active low
IRUZLUH25¶GPXOWLSOH
interrupt line
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
LM75A Digital Temperature Sensor and Thermal Watchdog With Two-Wire Interface
1 Features 3 Description
The LM75A is an industry-standard digital
1• No External Components Required temperature sensor with an integrated sigma-delta
• Shutdown Mode to Minimize Power Consumption analog-to-digital converter (ADC) and I2C interface.
• Up to Eight LM75As can be Connected to a Single The LM75A provides 9-bit digital temperature
Bus readings with an accuracy of ±2°C from –25°C to
100°C and ±3°C over –55°C to 125°C.
• Power up Defaults Permit Stand-Alone Operation
as Thermostat The LM75A operates with a single supply from 2.7 V
to 5.5 V. Communication is accomplished over a
• Key Specifications: 2-wire interface which operates up to 400 kHz. The
– Supply Voltage LM75A has three address pins, allowing up to eight
– LM75A: 2.7 V to 5.5 V LM75A devices to operate on the same 2-wire bus.
The LM75A has a dedicated overtemperature output
– Supply Current (O.S.) with programmable limit and hysteresis. This
– Operating: 280 μA (Typical) output has programmable fault tolerance, which lets
– Shutdown: 4 μA (Typical) the user to define the number of consecutive error
– Temperature Accuracy conditions that must occur before O.S. is activated.
The wide temperature and supply range and I2C
– 25°C to 100°C: ±2°C (Max) interface make the LM75A ideal for a number of
– 55°C to 125°C: ±3°C (Max) applications including base stations, electronic test
equipment, office electronics, personal computers,
2 Applications and any other system in which thermal management
is critical to performance. The LM75A is available in
• General System Thermal Management an SOIC-8 package and an VSSOP-8 package.
• Communications Infrastructure
• Electronic Test Equipment Device Information(1)
• Environmental Monitoring PART NUMBER PACKAGE BODY SIZE (NOM)
SOIC (8) 4.90 mm × 3.91 mm
LM75A VSSOP (8) 3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Typical Application
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
Table of Contents
7.3 Feature Description................................................. 10
1 Features.................................................................. 17.4 Device Functional Modes........................................ 10
2 Applications ........................................................... 17.5 Programming........................................................... 11
3 Description............................................................. 17.6 Register Maps......................................................... 13
4 Revision History..................................................... 28 Application and Implementation ........................ 15
5 Pin Configuration and Functions......................... 38.1 Application Information............................................ 15
6 Specifications......................................................... 38.2 Typical Applications ................................................ 15
6.1 Absolute Maximum Ratings ...................................... 38.3 System Examples ................................................... 16
6.2 ESD Ratings.............................................................. 39 Power Supply Recommendations...................... 18
6.3 Recommended Operating Conditions....................... 410 Layout................................................................... 18
6.4 Thermal Information.................................................. 410.1 Layout Guidelines ................................................. 18
6.5 Temperature-to-Digital Converter Characteristics..... 410.2 Layout Example .................................................... 19
6.6 Digital DC Characteristics......................................... 511 Device and Documentation Support................. 20
6.7 I2C Digital Switching Characteristics......................... 511.1 Trademarks........................................................... 20
6.8 Typical Characteristics.............................................. 911.2 Electrostatic Discharge Caution............................ 20
7 Detailed Description............................................ 10 11.3 Glossary................................................................ 20
7.1 Overview................................................................. 10 12 Mechanical, Packaging, and Orderable
7.2 Functional Block Diagram....................................... 10 Information........................................................... 20
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision O (May 2013) to Revision P Page
• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes,Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision N (May 2013) to Revision O Page
• Changed layout of National Data Sheet to TI format ........................................................................................................... 16
2Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
LM75A
www.ti.com
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
5 Pin Configuration and Functions
8-Pins
SOIC (D) and VSSOP (DGK) Packages
Top View
Pin Functions
PIN DESCRIPTION TYPICAL CONNECTION
NO. NAME
I2C Serial Bi-Directional Data Line, Open
1 SDA From Controller, tied to a pullup resistor or current source
Drain
2 SCL I2C Clock Input From Controller, tied to a pullup resistor or current source
Overtemperature Shutdown, Open Drain
3 O.S. Pull–up Resistor, Controller Interrupt Line
Output
4 GND Power Supply Ground Ground
5 A2
6 A1 User-Set I2C Address Inputs Ground (Low, “0”) or +VS(High, “1”)
7 A0 DC Voltage from 2.7 V to 5.5 V 100-nF bypass capacitor with 10-µF bulk
8 +VSPositive Supply Voltage Input capacitance in the near vicinity
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Supply Voltage Pin (+VS)−0.3 6.5 V
Voltage at A0, A1and A2 Pins −0.3 (+VS+ 0.3) and must be ≤6.5 V
Voltage at OS, SCL and SDA Pins −0.3 6.5 V
Input Current at any Pin(2) 5 mA
Package Input Current(2) 20 mA
O.S. Output Sink Current 10 mA
O.S. Output Voltage 6.5 V
Storage temperature, Tstg –65 150 °C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not
apply when operating the device beyond its rated operating conditions.
(2) When the input voltage (VI) at any pin exceeds the power supplies (VI< GND or VI> +VS) the current at that pin should be limited to
5mA. The 20mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an
input current of 5mA to four.
6.2 ESD Ratings VALUE UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2500
Charged-device model (CDM), per JEDEC specification JESD22- ±1000
V(ESD) Electrostatic discharge V
C101(2)
Machine model ±250
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Copyright © 2000–2014, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM75A
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
6.3 Recommended Operating Conditions(1)(2)
MIN MAX UNIT
Specified Temperature Range (TMIN to TMAX)−55 125 °C
Supply Voltage Range (+VS) LM75A 2.7 5.5 V
(1) LM75A θJA (thermal resistance, junction-to-ambient) when attached to a printed circuit board with 2 oz. foil similar to the one shown in
Thermal Information is summarized in the table below the Operating Ratings table.
(2) Reflow temperature profiles are different for lead-free and non-lead-free packages. Soldering process must comply with Reflow
Temperature Profile specifications. Refer to www.ti.com/packaging.(2)
6.4 Thermal Information LM75A
THERMAL METRIC(1) D DGK UNIT
8 PINS 8 PINS
RθJA Junction-to-ambient thermal resistance 200 250 °C/W
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.5 Temperature-to-Digital Converter Characteristics
Unless otherwise noted, these specifications apply for: +VS= 2.7 to 5.5 Vdc for LM75AIM. TA= TJ= 25°C, unless otherwise
noted. PARAMETER TEST CONDITIONS MIN TYP(1) MAX(2) UNIT
TA=−25°C to +100°C –2 2
–55°C ≤TJ≤125°C
Accuracy °C
TA=−55°C to +125°C –3 3
–55°C ≤TJ≤125°C
Resolution 9 Bits
Temperature Conversion Time See(3) 100 ms
See(3), –55°C ≤TJ≤125°C 300
I2C Inactive 0.28 mA
I2C Inactive, –55°C ≤TJ≤125°C 0.5
Quiescent Current LM75A Shutdown Mode, +VS= 3 V 4 μA
Shutdown Mode, +VS= 5 V 6 μA
O.S. Output Saturation Voltage IOUT = 4 mA, –55°C ≤TJ≤125°C 0.8 V
O.S. Delay See(4), –55°C ≤TJ≤125°C 1 6 Conversion
TOS Default Temperature See(5) 80 °C
THYST Default Temperature See(5) 75 °C
(1) Typicals are at TA= 25°C and represent most likely parametric norm.
(2) Maximum values (limits) are ensured to AOQL (Average Outgoing Quality Level).
(3) The conversion-time specification is provided to indicate how often the temperature data is updated. The LM75A can be accessed at
any time and reading the Temperature Register will yield result from the last temperature conversion. When the LM75A is accessed, the
conversion that is in process will be interrupted and it will be restarted after the end of the communication. Accessing the LM75A
continuously without waiting at least one conversion time between communications will prevent the device from updating the
Temperature Register with a new temperature conversion result. Consequently, the LM75A should not be accessed continuously with a
wait time of less than 300ms.
(4) O.S. Delay is user programmable up to 6 “over limit” conversions before O.S. is set to minimize false tripping in noisy environments.
(5) Default values set at power up.
4Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
LM75A
www.ti.com
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
6.6 Digital DC Characteristics
Unless otherwise noted, these specifications apply for +VS= 2.7 to 5.5 Vdc for LM75AIM and LM75AIMM. TA= TJ= 25°C,
unless otherwise noted.PARAMETER TEST CONDITIONS MIN TYP(1) MAX(2) UNIT
–55°C ≤TJ≤125°C +VS× 0.7 V
VIN(1) Logical “1” Input Voltage +VS+ 0.3 V
–55°C ≤TJ≤125°C −0.3 V
VIN(0) Logical “0” Input Voltage +VS× 0.3 V
VIN = +VS0.005
IIN(1) Logical “1” Input Current μA
VIN = +VS, –55°C ≤1.0
TJ≤125°C
VIN = 0 V −0.005
IIN(0) Logical “0” Input Current μA
VIN = 0 V, –55°C ≤ −1.0
TJ≤125°C
CIN All Digital Inputs 5 pF
High Level Output VOH = 5 V, –55°C ≤
IOH Current LM75A 1 μA
TJ≤125°C
Open drain leakage IOL = 3 mA, –55°C ≤0.4
VOL Low Level Output Voltage V
TJ≤125°C
CL= 400 pF IO= 3 250
tOF Output Fall Time mA, –55°C ≤TJ≤ns
125°C
(1) Typicals are at TA= 25°C and represent most likely parametric norm.
(2) Maximum values (limits) are ensured to AOQL (Average Outgoing Quality Level).
6.7 I2C Digital Switching Characteristics
Unless otherwise noted, these specifications apply for +VS= 2.7 to 5.5 Vdc for LM75AIM and LM75AIMM on output lines = 80
pF unless otherwise specified. TA= TJ= 25°C, unless otherwise noted.
PARAMETER TEST CONDITIONS MIN TYP(1) MAX(2)(3) UNIT
t1SCL (Clock) Period –55°C ≤TJ≤125°C 2.5 ns
t2Data in Set-Up Time to SCL High –55°C ≤TJ≤125°C 100 ns
t3Data Out Stable after SCL Low –55°C ≤TJ≤125°C 0 ns
t4SDA Low Set-Up Time to SCL Low (Start –55°C ≤TJ≤125°C 100 ns
Condition)
t5SDA High Hold Time after SCL High (Stop –55°C ≤TJ≤125°C 100 ns
Condition) 75
SDA Time Low for Reset of Serial
tTIMEOUT LM75A ms
Interface(4) –55°C ≤TJ≤125°C 325
(1) Typicals are at TA= 25°C and represent most likely parametric norm.
(2) Maximum values (limits) are ensured to AOQL (Average Outgoing Quality Level).
(3) Timing specifications are tested at the bus input logic levels (Vin(0)=0.3XVA for a falling edge and Vin(1)=0.7XVA for a rising edge)
when the SCL and SDA edge rates are similar.
(4) Holding the SDA line low for a time greater than tTIMEOUT will cause the LM75A to reset SDA to the IDLE state of the serial bus
communication (SDA set High).
Copyright © 2000–2014, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM75A
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
Figure 1. Timing Diagram
Figure 2. Temperature-to-Digital Transfer Function (Non-Linear Scale for Clarity)
Figure 3. Printed Circuit Board Used for Thermal Resistance Specifications
6Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
LM75A
www.ti.com
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
Figure 4. I2C Timing Diagram
Copyright © 2000–2014, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM75A
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
Figure 5. I2C Timing Diagrams (Continued)
8Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
LM75A
www.ti.com
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
6.8 Typical Characteristics
Figure 6. Accuracy vs Temperature (LM75A)
Copyright © 2000–2014, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM75A
7
6
5
A0
A1
A2
Temperature
Threshold
Silicon Bandgap
Temperature
Sensor
Ð
1-Bit
D/A
10-Bit
Digital
Decimation
Filter
9-Bit Sigma-Delta ADC
Configuration
Register
TOS Set Point
Register
Pointer
Register THYST Set
Point Register
Set Point
Comparator
3O.S.
Reset
1
2
SDA
SCL
Two-Wire Interface
4
8
+VS
GND
Product ID
Register
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
7 Detailed Description
7.1 Overview
The LM75A temperature sensor incorporates a band-gap type temperature sensor and 9-bit ADC (sigma-delta
ADC). The temperature data output of the LM75A is available at all times via the I2C bus. If a conversion is in
progress, it will be stopped and restarted after the read. A digital comparator is also incorporated that compares
a series of readings, the number of which is user-selectable, to user-programmable setpoint and hysteresis
values. The comparator trips the O.S. output line, which is programmable for mode and polarity. The LM75A has
an integrated low-pass filter on both the SDA and the SCL line. These filters increase communications reliability
in noisy environments.
The LM75A also has a bus fault timeout feature. If the SDA line is held low for longer than tTIMEOUT (see
specification) the LM75A will reset to the IDLE state (SDA set to high impedance) and wait for a new start
condition. The TIMEOUT feature is not functional in Shutdown Mode.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Digital Temperature Sensor
The LM75A is an industry-standard digital temperature sensor with an integrated sigma-delta ADC and I2C
interface. The LM75A provides 9-bit digital temperature readings with an accuracy of ±2°C from –25°C to 100°C
and ±3°C over –55°C to 125°C.
The LM75A operates with a single supply from +2.7 V to +5.5 V. Communication is accomplished over a 2-wire
interface which operates up to 400kHz. The LM75A has three address pins, allowing up to eight LM75A devices
to operate on the same 2-wire bus. The LM75A has a dedicated over-temperature output (O.S.) with
programmable limit and hysteresis. This output has programmable fault tolerance, which allows the user to
define the number of consecutive error conditions that must occur before O.S. is activated.
7.4 Device Functional Modes
In Comparator mode the O.S. Output behaves like a thermostat. The output becomes active when temperature
exceeds the TOS limit, and leaves the active state when the temperature drops below the THYST limit. In this mode
the O.S. output can be used to turn a cooling fan on, initiate an emergency system shutdown, or reduce system
clock speed. Shutdown mode does not reset O.S. state in a comparator mode.
In Interrupt mode exceeding TOS also makes O.S. active but O.S. will remain active indefinitely until reset by
reading any register via the I2C interface. Once O.S. has been activated by crossing TOS, then reset, it can be
activated again only by Temperature going below THYST. Again, it will remain active indefinitely until being reset
by a read. Placing the LM75A in shutdown mode also resets the O.S. Output.
10 Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
LM75A
www.ti.com
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
Device Functional Modes (continued)
The LM75A always powers up in a known state. The power up default conditions are:
• Comparator mode
• TOS = 80°C
• THYST = 75°C
• O.S. active low
• Pointer = “00”
When the supply voltage is less than about 1.7V, the LM75A is considered powered down. As the supply voltage
rises above the nominal 1.7V power up threshold, the internal registers are reset to the power up default values
listed above.
If the LM75A is not connected to the I2C bus on power up, it will act as a stand-alone thermostat with the power
up default conditions listed above. It is optional, but recommended, to connect the address pins (A2, A1, A0) and
the SCL and SDA pins together and to a 10k pullup resistor to +VSfor better noise immunity. Any of these pins
may also be tied high separately through a 10-k pullup resistor.
7.5 Programming
7.5.1 I2C Bus Interface
The LM75A operates as a slave on the I2C bus, so the SCL line is an input (no clock is generated by the LM75A)
and the SDA line is a bi-directional serial data path. According to I2C bus specifications, the LM75A has a 7-bit
slave address. The four most significant bits of the slave address are hard wired inside the LM75A and are
“1001”. The three least significant bits of the address are assigned to pins A2–A0, and are set by connecting
these pins to ground for a low, (0); or to +VSfor a high, (1).
Therefore, the complete slave address is:
1 0 0 1 A2 A1 A0
MSB LSB
These interrupt mode resets of O.S. occur only when LM75A is read or placed in shutdown. Otherwise, O.S. would
remain active indefinitely for any event.
Figure 7. O.S. Output Temperature Response Diagram
Copyright © 2000–2014, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM75A
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
7.5.2 Temperature Data Format
Temperature data can be read from the Temperature, TOS Set Point, and THYST Set Point registers; and written to
the TOS Set Point, and THYST Set Point registers. Temperature data is represented by a 9-bit, two's complement
word with an LSB (Least Significant Bit) equal to 0.5°C:
Digital Output
Temperature Binary Hex
+125°C 0 1111 1010 0FAh
+25°C 0 0011 0010 032h
+0.5°C 0 0000 0001 001h
0°C 0 0000 0000 000h
−0.5°C 1 1111 1111 1FFh
−25°C 1 1100 1110 1CEh
−55°C 1 1001 0010 192h
7.5.3 Shutdown Mode
Shutdown mode is enabled by setting the shutdown bit in the Configuration register via the I2C bus. Shutdown
mode reduces power supply current significantly. See specified quiescent current specification in the electrical
tables. In Interrupt mode O.S. is reset if previously set and is undefined in Comparator mode during shutdown.
The I2C interface remains active. Activity on the clock and data lines of the I2C bus may slightly increase
shutdown mode quiescent current. TOS, THYST, and Configuration registers can be read from and written to in
shutdown mode.
For the LM75A, the TIMEOUT feature is turned off in Shutdown Mode.
7.5.4 Fault Queue
A fault queue of up to 6 faults is provided to prevent false tripping of O.S. when the LM75A is used in noisy
environments. The number of faults set in the queue must occur consecutively to set the O.S. output.
7.5.5 Comparator and Interrupt Mode
As indicated in the O.S. Output Temperature Response Diagram, Figure 7, the events that trigger O.S. are
identical for either Comparator or Interrupt mode. The most important difference is that in Interrupt mode the O.S.
will remain set indefinitely once it has been set. To reset O.S. while in Interrupt mode, perform a read from any
register in the LM75A.
7.5.6 O.S. Output
The O.S. output is an open-drain output and does not have an internal pullup. A “high” level will not be observed
on this pin until pullup current is provided from some external source, typically a pullup resistor. Choice of
resistor value depends on many system factors but, in general, the pullup resistor should be as large as possible.
This will minimize any errors due to internal heating of the LM75A. The maximum resistance of the pullup, based
on LM75A specification for High Level Output Current, to provide a 2-V high level, is 30 kΩ.
7.5.7 O.S. Polarity
The O.S. output can be programmed via the configuration register to be either active low (default mode), or
active high. In active low mode the O.S. output goes low when triggered exactly as shown on the O.S. Output
Temperature Response Diagram, Figure 7. Active high simply inverts the polarity of the O.S. output.
12 Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
I2C Interface
SDA
SCL
Pointer Register
(Selects register for
communication)
AddressData
Temperature
(Read-Only)
Pointer = 00000000
Product ID
(Read-Only)
Pointer = 00000111
TOS Set Point
(Read-Write)
Pointer = 00000011
Configuration
(Read-Write)
Pointer = 00000001
THYST Set Point
(Read-Write)
Pointer = 00000010
LM75A
www.ti.com
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
7.5.8 Internal Register Structure
Figure 8. Register Structure
There are four data registers in the LM75A and an additional Product ID register selected by the Pointer register.
At power-up the Pointer is set to “000”; the location for the Temperature Register. The Pointer register latches
whatever the last location it was set to. In Interrupt Mode, a read from the LM75A, or placing the device in
shutdown mode, resets the O.S. output. All registers are read and write, except the Temperature register and the
LM75A's Product ID register, which are read-only.
A write to the LM75A will always include the address byte and the Pointer byte. A write to the Configuration
register requires one data byte, and the TOS and THYST registers require two data bytes.
Reading the LM75A can take place either of two ways: If the location latched in the Pointer is correct (most of the
time it is expected that the Pointer will point to the Temperature register because it will be the data most
frequently read from the LM75A), then the read can simply consist of an address byte, followed by retrieving the
corresponding number of data bytes. If the Pointer needs to be set, then an address byte, pointer byte, repeat
start, and another address byte will accomplish a read.
The first data byte is the most significant byte with most significant bit first, permitting only as much data as
necessary to be read to determine temperature condition. For instance, if the first four bits of the temperature
data indicates an overtemperature condition, the host processor could immediately take action to remedy the
excessive temperatures. At the end of a read, the LM75A can accept either Acknowledge or No Acknowledge
from the Master (No Acknowledge is typically used as a signal for the slave that the Master has read its last
byte).
7.6 Register Maps
7.6.1 Pointer Register (Selects Which Registers Will Be Read From or Written to):
P7 P6 P5 P4 P3 P2 P1 P0
0 0 0 0 0 Register Select
P0-P1: Register Select:
P2 P1 P0 Register
0 0 0 Temperature (Read-only) (Power-up default)
0 0 1 Configuration (Read/Write)
0 1 0 THYST (Read/Write)
0 1 1 TOS (Read/Write)
1 1 1 Product ID Register
Copyright © 2000–2014, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM75A
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
P3–P7: Must be kept zero.
7.6.2 Temperature Register (Read-Only):
D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
MSB Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB X X X X X X X
D0–D6: Undefined. D7–D15: Temperature Data. One LSB = 0.5°C. Two's complement format.
7.6.3 Configuration Register (Read/Write):
D7 D6 D5 D4 D3 D2 D1 D0
0 0 0 Fault Queue O.S. Polarity Cmp/Int Shutdown
Power up default is with all bits “0” (zero).
D0: Shutdown: When set to 1 the LM75A goes to low power shutdown mode.
D1: Comparator/Interrupt mode: 0 is Comparator mode, 1 is Interrupt mode.
D2: O.S. Polarity: 0 is active low, 1 is active high. O.S. is an open-drain output under all conditions.
D3–D4: Fault Queue: Number of faults necessary to detect before setting O.S. output to avoid false tripping due
to noise. Faults are determine at the end of a conversion. See specified temperature conversion time in the
electrical tables.
D4 D3 Number of Faults
0 0 1 (Power-up default)
0 1 2
1 0 4
1 1 6
D5–D7: These bits are used for production testing and must be kept zero for normal operation.
7.6.4 THYST and TOS Register (Read/Write):
D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
MSB Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB X X X X X X X
D0–D6: Undefined D7–D15: THYST Or TOS Trip Temperature Data. Power up default is TOS = 80°C, THYST =
75°C
7.6.5 PRODID: Product ID Register (Read-Only) Pointer Address: 07h
D7 D6 D5 D4 D3 D2 D1 D0
10100001
D4--D7 Product Identification Nibble. Always returns Ah to uniquely identify this part as the LM75A.
D0--D3 Die Revision Nibble. Returns 1h to uniquely identify the revision level as one.
14 Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
+VS
O.S.
GND
8
3
4
LM75A
C1
100 nF
+12V
+12V/300 mA
Fan Motor
R1
10k R2
10k
Q2
NDP410A
series
Q1
2N3904
R3
10k
7
6
5
1
2
A0
A1
A2
SCL
SDA
Optional but
Recommended
Pull-up
In Stand-alone
Mode
LM75A
www.ti.com
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The wide temperature and supply range and I2C interface make the LM75A ideal for a number of applications
including base stations, electronic test equipment, office electronics, personal computers, and any other system
where thermal management is critical to performance.
8.2 Typical Applications
8.2.1 Simple Fan Controller, Interface Optional
When using the two-wire interface: program O.S. for active high and connect O.S. directly to Q2's gate.
Figure 9. Simple Fan Controller, Interface Optional
8.2.1.1 Design Requirements
The LM75A requires positive supply voltage of 2.7 V to 5.5 V to be applied between +Vs and GND. For best
results, bypass capacitors of 100 nF and 10 µF are recommended. Pullup resistors of 10 kΩare required on SCL
and SDA.
8.2.1.2 Detailed Design Procedure
Accessing the conversion result of the LM75A consists of writing an address byte followed by retrieving the
corresponding number of data bytes. The first data byte is the most significant byte with the most significant bit
first, permitting only as much data as necessary to be read to determine temperature condition. For instance, if
the first four bits of the temperature data indicates an overtemperature condition, the host processor could
immediately take action to remedy the excessive temperatures. At the end of a read, the LM75A can accept
either Acknowledge or No Acknowledge from the Master (No Acknowledge is typically used as a signal for the
slave that the Master has read its last byte). Temperature data is two's complement format and one LSB is
equivalent to 0.5°C.
Copyright © 2000–2014, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM75A
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
Typical Applications (continued)
8.2.1.3 Application Curve
Figure 10. Temperature Accuracy
8.3 System Examples
8.3.1 Simple Thermostat, Interface Optional
Figure 11. Simple Thermostat, Interface Optional
16 Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
+VS
O.S.
GND
8
3
4
LM75A
C6
100 nF R1
10k
R3
10k
7
6
5
1
2
A0
A1
A2
SCL
SDA
Optional but
Recommended
Pull-up
In Stand-alone
Mode
SHUTDOWN
BYPASS
+IN
-IN
C2
100 nF
C1
100 nF
R5 200k
R2
10k R3
10k R4
10k
C3
6.8 nF C4
6.8 nF C5
6.8 nF
GND
Vo2
Vo1
VDD
LM4861M
LM75A
www.ti.com
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
System Examples (continued)
8.3.2 Temperature Sensor with Loudmouth Alarm (Barking Watchdog)
Figure 12. Temperature Sensor with Loudmouth Alarm (Barking Watchdog)
Copyright © 2000–2014, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM75A
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
9 Power Supply Recommendations
The LM75A is specified for operation from 2.7 V to 5.5 V. Place 100-nF and 10-µF capacitors close to +Vs in
order to reduce errors coupling in from noisy or high impedance supplies.
10 Layout
10.1 Layout Guidelines
To achieve the expected results when measuring temperature with an integrated circuit temperature sensor like
the LM75A, it is important to understand that the sensor measures its own die temperature. For the LM75A, the
best thermal path between the die and the outside world is through the LM75A's pins. In the VSSOP-8 package,
the GND pin is directly connected to the die, so the GND pin provides the best thermal path. If the other pins are
at different temperatures (unlikely, but possible), they will affect the die temperature, but not as strongly as the
GND pin. In the SOIC-8 package, none of the pins is directly connected to the die, so they will all contribute
similarly to the die temperature. Because the pins represent a good thermal path to the LM75A die, the LM75A
will provide an accurate measurement of the temperature of the printed circuit board on which it is mounted.
There is a less efficient thermal path between the plastic package and the LM75A die. If the ambient air
temperature is significantly different from the printed circuit board temperature, it will have a small effect on the
measured temperature.
In probe-type applications, the LM75A can be mounted inside a sealed-end metal tube, and can then be dipped
into a bath or screwed into a threaded hole in a tank. As with any IC, the LM75A and accompanying wiring and
circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may
operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as
Humiseal and epoxy paints or dips are often used to insure that moisture cannot corrode the LM75A or its
connections.
10.1.1 Digital Noise Issues
The LM75A features an integrated low-pass filter on both the SCL and the SDA digital lines to mitigate the
effects of bus noise. Although this filtering makes the LM75A communication robust in noisy environments, good
layout practices are always recommended. Minimize noise coupling by keeping digital traces away from
switching power supplies. Also, ensure that digital lines containing high-speed data communications cross at
right angles to the SDA and SCL lines. Excessive noise coupling into the SDA and SCL lines on the
LM75A—specifically noise with amplitude greater than 400 mVpp (the LM75A’s typical hysteresis), overshoot
greater than 300mV above +Vs, and undershoot more than 300 mV below GND—may prevent successful serial
communication with the LM75A. Serial bus no-acknowledge is the most common symptom, causing unnecessary
traffic on the bus. Although the serial bus maximum frequency of communication is only 400 kHz, care must be
taken to ensure proper termination within a system with long printed circuit board traces or multiple parts on the
bus.
18 Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
LM75A
www.ti.com
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
10.2 Layout Example
Figure 13. Printed Circuit Board Used for Thermal Resistance Specifications
Copyright © 2000–2014, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM75A
LM75A
SNOS808P –JANUARY 2000–REVISED DECEMBER 2014
www.ti.com
11 Device and Documentation Support
11.1 Trademarks
All trademarks are the property of their respective owners.
11.2 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.3 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
20 Submit Documentation Feedback Copyright © 2000–2014, Texas Instruments Incorporated
Product Folder Links: LM75A
PACKAGE OPTION ADDENDUM
www.ti.com 6-Feb-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM75AIM/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) SN Level-1-260C-UNLIM -55 to 125 LM75
AIM
LM75AIMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) SN Level-1-260C-UNLIM -55 to 125 T00A
LM75AIMME/NOPB ACTIVE VSSOP DGK 8 250 Green (RoHS
& no Sb/Br) SN Level-1-260C-UNLIM -55 to 125 T00A
LM75AIMMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS
& no Sb/Br) SN Level-1-260C-UNLIM -55 to 125 T00A
LM75AIMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) SN Level-1-260C-UNLIM -55 to 125 LM75
AIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 6-Feb-2020
Addendum-Page 2
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM75AIMM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM75AIMME/NOPB VSSOP DGK 8 250 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM75AIMMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM75AIMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 22-Oct-2014
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM75AIMM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LM75AIMME/NOPB VSSOP DGK 8 250 210.0 185.0 35.0
LM75AIMMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0
LM75AIMX/NOPB SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 22-Oct-2014
Pack Materials-Page 2
www.ti.com
PACKAGE OUTLINE
C
.228-.244 TYP
[5.80-6.19]
.069 MAX
[1.75]
6X .050
[1.27]
8X .012-.020
[0.31-0.51]
2X
.150
[3.81]
.005-.010 TYP
[0.13-0.25]
0 - 8 .004-.010
[0.11-0.25]
.010
[0.25]
.016-.050
[0.41-1.27]
4X (0 -15 )
A
.189-.197
[4.81-5.00]
NOTE 3
B .150-.157
[3.81-3.98]
NOTE 4
4X (0 -15 )
(.041)
[1.04]
SOIC - 1.75 mm max heightD0008A
SMALL OUTLINE INTEGRATED CIRCUIT
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
18
.010 [0.25] C A B
5
4
PIN 1 ID AREA
SEATING PLANE
.004 [0.1] C
SEE DETAIL A
DETAIL A
TYPICAL
SCALE 2.800
www.ti.com
EXAMPLE BOARD LAYOUT
.0028 MAX
[0.07]
ALL AROUND
.0028 MIN
[0.07]
ALL AROUND
(.213)
[5.4]
6X (.050 )
[1.27]
8X (.061 )
[1.55]
8X (.024)
[0.6]
(R.002 ) TYP
[0.05]
SOIC - 1.75 mm max heightD0008A
SMALL OUTLINE INTEGRATED CIRCUIT
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
METAL SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
EXPOSED
METAL
OPENING
SOLDER MASK METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
EXPOSED
METAL
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SYMM
1
45
8
SEE
DETAILS
SYMM
www.ti.com
EXAMPLE STENCIL DESIGN
8X (.061 )
[1.55]
8X (.024)
[0.6]
6X (.050 )
[1.27] (.213)
[5.4]
(R.002 ) TYP
[0.05]
SOIC - 1.75 mm max heightD0008A
SMALL OUTLINE INTEGRATED CIRCUIT
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
SYMM
SYMM
1
45
8
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated