1. General description
The 74LVC1G66-Q100 provides one single pole, single-thro w analog switch function. It
has two input/outp ut terminals (Yand Z) and an active HIGH enable i nput pin (E). When E
is LOW, the analog switch is turned off.
Schmitt trigger action at the enable input makes the circuit tolerant of slower input rise and
fall times across the entire VCC range from 1.65 V to 5.5 V.
This product has been qualified to the Automotive Electronics Council (AEC) standard
Q100 (Grade 1) and is suitable for use in automotive applications.
2. Features and benefits
Automotive product qualification in accordance with AEC-Q100 (Grade 1)
Specified from 40 C to +85 C and from 40 C to +125 C
Wide supply voltage range from 1.65 V to 5.5 V
Very low ON resistance:
7.5 (typical) at VCC =2.7V
6.5 (typical) at VCC =3.3V
6 (typical) at VCC =5V
Switch current capability of 32 mA
High noise immunity
CMOS low power consumption
TTL interface compatibility at 3.3 V
Latch-up performance meets requirements of JESD78 Class I
ESD protection:
MIL-STD-883, method 3015 exceeds 2000 V
HBM JESD22-A114F exceeds 2000 V
MM JESD22-A115-A exceeds 200 V (C = 200 pF, R = 0 )
Enable input accepts voltages up to 5.5 V
Multiple package options
74LVC1G66-Q100
Bilateral switch
Rev. 2 — 9 December 2016 Product data sheet
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 2 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
3. Ordering information
4. Marking
[1] The pin 1 indicator is located on the lo wer left corner of the device, below the marking code.
5. Functional diagram
Table 1. Ordering information
Type number Package
Temperature range Name Description Version
74LVC1G66GW-Q100 40 Cto+125C TSSOP5 plastic thin shrink small outline package; 5 leads;
body wid th 1.25 mm SOT353-1
74LVC1G66GV-Q100 40 Cto+125C SC-74A plastic surface-mounted package; 5 leads SOT753
Table 2. Marking
Type number Marking code[1]
74LVC1G66GW-Q100 VL
74LVC1G66GV-Q100 V66
Fig 1. Logic symbol Fig 2. IEC logic symbol
DDJ
(
=<
PQD
;
Fig 3. Logic diagra m
DDP
9&&
(
<
=
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 3 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
6. Pinning information
6.1 Pinning
6.2 Pin description
7. Functional description
[1] H = HIGH voltage level; L = LOW voltage level
Fig 4. Pin configuration SOT353-1 and SOT753
/9&*4
<
9&&
=
*1' (
DDD
Table 3. Pin description
Symbol Pin Symbol
Y 1 independent input or outp ut
Z 2 independent output or input
GND 3 ground (0 V)
E 4 enable input (active HIGH)
VCC 5 supply voltage
Table 4. Function table[1]
Input E Switch
LOFF-state
H ON-state
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 4 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
8. Limiting values
[1] The minimum input voltage rating may be exceeded if the input current rating is observed.
[2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed.
[3] For TSSOP5 and SC-74A packages: above 87.5 C the value of Ptot derates linearly with 4.0 mW/K.
For XSON6 packages: above 118 C the value of Ptot derates linearly with 7.8 mW/K.
9. Recommended operating conditions
[1] To avoid sinking GND current from terminal Z when switch current flows in terminal Y, the voltage drop across the bidirectional switch
must not exceed 0.4 V. If the switch current flows into terminal Z, no GND current flows from terminal Y. In this case, there is no limit for
the voltage drop across the switch.
[2] Applies to control signal levels.
Table 5. L imiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Min Max Unit
VCC supply voltage 0.5 +6.5 V
VIinput voltage [1] 0.5 +6.5 V
IIK input clamping current VI<0.5 V or VI>V
CC +0.5V 50 - mA
ISK switch clamping current VI<0.5 V or VI>V
CC +0.5V - 50 mA
VSW switch voltage enable and disable mode [2] 0.5 VCC +0.5 V
ISW switch current VSW >0.5 V or VSW <V
CC +0.5V - 50 mA
ICC supply current - 100 mA
IGND ground current 100 - mA
Tstg storage temperature 65 +150 C
Ptot total power dissipation Tamb =40 C to +125 C[3] - 250 mW
Table 6. Recommended operating conditions
Symbol Parameter Conditions Min Typ Max Unit
VCC supply voltage 1.65 - 5.5 V
VIinput voltage 0 - 5.5 V
VSW switch voltage [1] 0-V
CC V
Tamb ambient temp erature 40 - +125 C
t/V input transition rise and
fall rate VCC = 1.65 V to 2.7 V [2] --20ns/V
VCC = 2.7 V to 5.5 V [2] --10ns/V
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 5 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
10. Static characteristics
[1] All typical values are measured at Tamb =25C.
[2] These typical values are measured at VCC =3.3V.
Table 7. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit
Min Typ[1] Max Min Max
VIH HIGH-level input
voltage VCC = 1.65 V to 1.95 V 0.65VCC - - 0.65VCC -V
VCC = 2.3 V to 2.7 V 1.7 - - 1.7 - V
VCC = 2.7 V to 3.6 V 2.0 - - 2.0 - V
VCC = 4.5 V to 5.5 V 0.7VCC - - 0.7VCC -V
VIL LOW-level input
voltage VCC = 1.65 V to 1.95 V - - 0.35VCC -0.35V
CC V
VCC = 2.3 V to 2.7 V - - 0.7 - 0.7 V
VCC = 2.7 V to 3.6 V - - 0.8 - 0.8 V
VCC = 4.5 V to 5.5 V - - 0.3VCC -0.3V
CC V
IIinput leakage
current pin E; VI= 5.5 V or GND;
VCC = 0 V to 5.5 V [2] -0.1 1-1A
IS(OFF) OFF-state
leakage current VCC = 5.5 V; see Figure 5 [2] -0.1 0.2 - 0.5 A
IS(ON) ON-state leakage
current VCC = 5.5 V; see Figure 6 [2] -0.1 1-2A
ICC supply current VI= 5.5 Vor GND;
VSW =GNDorV
CC;
VCC = 1.65 V to 5.5 V
[2] -0.14 - 4A
ICC additional supply
current pin E; VI=V
CC 0.6 V;
VSW =GNDorV
CC; VCC =5.5V [2] -5500-500A
CIinput capacitance - 2.0 - - - pF
CS(OFF) OFF-state
capacitance -6.5---pF
CS(ON) ON-state
capacitance -11---pF
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 6 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
10.1 Test circuits
10.2 ON resistance
VI = VCC or GND and VO = GND or VCC.V
I = VCC or GND and VO = open circuit.
Fig 5. Test circuit for measuring OFF-state leakage
current Fig 6. Test circuit for measuring ON-state leakage
current
DDP
,6
9,
9,/
92
9&&
*1'
<=
(
DDP
,6
9,
9,+
92
9&&
*1'
<=
(
Table 8. ON resistance
At recommended operating conditions; voltages are referenced to GND (ground 0 V); for graphs see Figure 8 to Figure 13.
Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit
Min Typ[1] Max Min Max
RON(peak) ON resistance
(peak) VI=GNDtoV
CC; see Figure 7
ISW =4mA; V
CC = 1.65 V to 1.95 V - 34.0 130 - 195
ISW =8mA; V
CC = 2.3 V to 2.7 V - 12.0 30 - 45
ISW =12mA; V
CC = 2.7 V - 10.4 25 - 38
ISW =24mA; V
CC = 3.0 V to 3.6 V - 7.8 20 - 30
ISW =32mA; V
CC = 4.5 V to 5.5 V - 6.2 15 - 23
RON(rail) ON resistance
(rail) VI= GND; see Figure 7
ISW =4mA; V
CC = 1.65 V to 1.95 V - 8.2 18 - 27
ISW =8mA; V
CC = 2.3 V to 2.7 V - 7.1 16 - 24
ISW =12mA; V
CC = 2.7 V - 6.9 14 - 21
ISW =24mA; V
CC = 3.0 V to 3.6 V - 6.5 12 - 18
ISW =32mA; V
CC = 4.5 V to 5.5 V - 5.8 10 - 15
VI=V
CC; see Figure 7
ISW =4mA; V
CC = 1.65 V to 1.95 V - 10.4 30 - 45
ISW =8mA; V
CC = 2.3 V to 2.7 V - 7.6 20 - 30
ISW =12mA; V
CC = 2.7 V - 7.0 18 - 27
ISW =24mA; V
CC = 3.0 V to 3.6 V - 6.1 15 - 23
ISW =32mA; V
CC = 4.5 V to 5.5 V - 4.9 10 - 15
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 7 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
[1] Typical values are measured at Tamb = 25 C and nominal VCC.
[2] Flatness is defined as the difference between the maximum and minimum value of ON resistance measured at identical VCC and
temperature.
10.3 ON resistance test circuit and graphs
RON(flat) ON resistance
(flatness) VI=GNDtoV
CC [2]
ISW =4mA; V
CC = 1.65 V to 1.95 V - 26.0 - - -
ISW =8mA; V
CC = 2.3 V to 2.7 V - 5.0 - - -
ISW =12mA; V
CC =2.7V - 3.5 - - -
ISW =24mA; V
CC = 3.0 V to 3.6 V - 2.0 - - -
ISW =32mA; V
CC = 4.5 V to 5.5 V - 1.5 - - -
Table 8. ON resistance …continued
At recommended operating conditions; voltages are referenced to GND (ground 0 V); for graphs see Figure 8 to Figure 13.
Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit
Min Typ[1] Max Min Max
RON =V
SW / ISW.(1)V
CC = 1.8 V.
(2) VCC = 2.5 V.
(3) VCC = 2.7 V.
(4) VCC = 3.3 V.
(5) VCC = 5.0 V.
Fig 7. Test circuit for measuring ON resistance Fig 8. Typical ON resistance as a function of input
voltage; Tamb = 25 C
DDP
9,
9,+
9&&
*1'
=<
(
96:
,6:
9
,
9
PQD
5
21
ȍ
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 8 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
(1) Tamb = 125 C.
(2) Tamb =85C.
(3) Tamb =25C.
(4) Tamb =40 C.
(1) Tamb = 125 C.
(2) Tamb =85C.
(3) Tamb =25C.
(4) Tamb =40 C.
Fig 9. ON resistance as a function of input voltage;
VCC =1.8V Fig 10. ON resistance as a function of input voltage;
VCC =2.5V
9
,
9
DDD
5
21
ȍ
9
,
9
DDD
5
21
ȍ
(1) Tamb = 125 C.
(2) Tamb =85C.
(3) Tamb =25C.
(4) Tamb =40 C.
(1) Tamb = 125 C.
(2) Tamb =85C.
(3) Tamb =25C.
(4) Tamb =40 C.
Fig 11. ON resistance as a function of input voltage;
VCC =2.7V Fig 12. ON resistance as a function of input voltage;
VCC =3.3V
DDD
9
,
9
5
21
ȍ
9
,
9
DDD
5
21
ȍ
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 9 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
11. Dynamic characteristics
(1) Tamb = 125 C.
(2) Tamb =85C.
(3) Tamb =25C.
(4) Tamb =40 C.
Fig 13. ON resistance as a function of input voltage; VCC =5.0V
9
,
9
DDD
5
21
ȍ
Table 9. Dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for test circuit see Figure 16.
Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit
Min Typ[1] Max Min Max
tpd propagation delay Y to Z or Z to Y;
see Figure 14 [2][3]
VCC = 1.65 V to 1.95 V - 0.8 2.0 - 3.0 ns
VCC = 2.3 V to 2.7 V - 0.4 1.2 - 2.0 ns
VCC = 2.7 V - 0.4 1.0 - 1.5 ns
VCC = 3.0 V to 3.6 V - 0.3 0.8 - 1.5 ns
VCC = 4.5 V to 5.5 V - 0.2 0.6 - 1.0 ns
ten enable time E to Y or Z; see Figure 15 [4]
VCC = 1.65 V to 1.95 V 1.0 5.3 12 1.0 15.5 ns
VCC = 2.3 V to 2.7 V 1.0 3.0 6.5 1.0 8.5 ns
VCC = 2.7 V 1.0 2.6 6.0 1.0 8.0 ns
VCC = 3.0 V to 3.6 V 1.0 2.5 5.0 1.0 6.5 ns
VCC = 4.5 V to 5.5 V 1.0 1.9 4.2 1.0 5.5 ns
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 10 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
[1] Typical values are measured at Tamb =25C and nominal VCC.
[2] tpd is the same as tPLH and tPHL
[3] propagation delay is the calculated RC time constant of the typical ON resistance of the switch and the specified capacitance when
driven by an ideal voltage source (zero output impedance).
[4] ten is the same as tPZH and tPZL
[5] tdis is the same as tPLZ and tPHZ
[6] CPD is used to determine the dynamic power dissipation (PD in W).
PD=C
PD VCC2fiN+{(CL+C
S(ON))VCC2fo} where:
fi= input frequency in MHz;
fo= output frequency in MHz;
CL= output load capacitance in pF;
CS(ON) = maximum ON-state switch capacitance in pF;
VCC = supply voltage in V;
N = number of inputs switching;
{(CL+C
S(ON)) VCC2fo} = sum of the outputs.
11.1 Waveforms and test circuit
tdis disable time E to Y or Z; see Figure 15 [5]
VCC = 1.65 V to 1.95 V 1.0 4.2 10 1.0 13 ns
VCC = 2.3 V to 2.7 V 1.0 2.4 6.9 1.0 9.0 ns
VCC = 2.7 V 1.0 3.6 7.5 1.0 9.5 ns
VCC = 3.0 V to 3.6 V 1.0 3.4 6.5 1.0 8.5 ns
VCC = 4.5 V to 5.5 V 1.0 2.5 5.0 1.0 6.5 ns
CPD power dissipation
capacitance CL=50pF; f
i=10MHz;
VI=GNDtoV
CC
[6]
VCC =2.5V - 9.8 - - - pF
VCC =3.3V - 12.0 - - - pF
VCC =5.0V - 17.3 - - - pF
Table 9. Dynamic characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for test circuit see Figure 16.
Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit
Min Typ[1] Max Min Max
Measurement points are given in Table 10.
Logic levels: VOL and VOH are typical output voltage levels that occur with the output load.
Fig 14. Input (Y or Z) to output (Z or Y) propagation delay s
PQD
W3/+ W3+/
90
90
<RU=LQSXW
=RU<RXWSXW
*1'
9,
92+
92/
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 11 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
Measurement points are given in Table 10.
Logic levels: VOL and VOH are typical output voltage levels that occur with the output load.
Fig 15. E nable and disabl e times
PQD
W3/=
W3+=
VZLWFK
GLVDEOHG
VZLWFK
HQDEOHG
9<
9;
VZLWFK
HQDEOHG
RXWSXW
/2:WR2))
2))WR/2:
RXWSXW
+,*+WR2))
2))WR+,*+
(
<RU=
<RU=
9,
92/
92+
9&&
90
*1'
*1'
W3=/
W3=+
90
90
Table 10. Measurement points
Supply voltage Input Output
VCC VMVMVXVY
1.65 V to 1.95 V 0.5VCC 0.5VCC VOL + 0.15 V VOH 0.15 V
2.3 V to 2.7 V 0.5VCC 0.5VCC VOL + 0.15 V VOH 0.15 V
2.7V 1.5V 1.5V V
OL + 0.3 V VOH 0.3 V
3.0Vto3.6V 1.5V 1.5 V V
OL + 0.3 V VOH 0.3 V
4.5 V to 5.5 V 0.5VCC 0.5VCC VOL + 0.3 V VOH 0.3 V
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 12 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
11.2 Additional dynamic characteristics
Test data is given in Table 11.
Definitions for test circuit:
RT = Termination resistance should be equal t o output impedance Zo of the pulse generator.
CL = Load capacitance including jig and probe capacitance.
RL = Load resistance.
VEXT = External voltage for measuring switching times.
Fig 16. Test circuit for measuring switching times
9(;7
9&&
9,92
PQD
'87
&/
57
5/
5/
*
Table 11. Test data
Supply voltage Input Load VEXT
VCC VItr, tfCLRLtPLH, tPHL tPZH, tPHZ tPZL, tPLZ
1.65 V to 1.95 V VCC 2.0ns 30pF 1kopen GND 2VCC
2.3 V to 2.7 V VCC 2.0ns 30pF 500open GND 2VCC
2.7 V 2.7 V 2.5ns 50pF 500open GND 6 V
3.0 V to 3.6 V 2.7 V 2.5ns 50pF 500open GND 6 V
4.5 V to 5.5 V VCC 2.5ns 50pF 500open GND 2VCC
Table 12. Additional dynamic characte ristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); Tamb =25
C.
Symbol Parameter Conditions Min Typ Max Unit
THD total ha rmo nic distortion RL=10k; CL=50pF; f
i= 1 kHz;
see Figure 17
VCC =1.65V - 0.032 - %
VCC = 2.3 V - 0.008 - %
VCC = 3.0 V - 0.006 - %
VCC = 4.5 V - 0.001 - %
RL=10k; CL=50pF; f
i=10kHz;
see Figure 17
VCC =1.65V - 0.068 - %
VCC = 2.3 V - 0.009 - %
VCC = 3.0 V - 0.008 - %
VCC = 4.5 V - 0.006 - %
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 13 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
f(3dB) 3 dB frequency response RL=600; CL=50pF;
see Figure 18
VCC = 1.65 V - 135 - MHz
VCC = 2.3 V - 145 - MHz
VCC = 3.0 V - 150 - MHz
VCC = 4.5 V - 155 - MHz
RL=50; C L= 5 pF; see Figure 18
VCC =1.65V - 500 - MHz
VCC =2.3V - 500 - MHz
VCC =3.0V - 500 - MHz
VCC =4.5V - 500 - MHz
RL=50; C L= 10 pF; see Figure 18
VCC = 1.65 V - 200 - MHz
VCC = 2.3 V - 350 - MHz
VCC = 3.0 V - 410 - MHz
VCC = 4.5 V - 440 - MHz
iso isolation (OFF-state) RL=600; CL=50pF; f
i= 1 MHz;
see Figure 19
VCC =1.65V - 46 - dB
VCC =2.3V - 46 - dB
VCC =3.0V - 46 - dB
VCC =4.5V - 46 - dB
RL=50; C L=5pF; f
i=1MHz;
see Figure 19
VCC =1.65V - 37 - dB
VCC =2.3V - 37 - dB
VCC =3.0V - 37 - dB
VCC =4.5V - 37 - dB
Vct crosstalk voltage between digital input and switch;
RL=600; CL=50pF; f
i= 1 MHz;
tr=t
f = 2 ns; see Figure 20
VCC =1.65V - 69 - mV
VCC =2.3V - 87 - mV
VCC = 3.0 V - 156 - mV
VCC = 4.5 V - 302 - mV
Table 12. Additional dynamic characte ristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); Tamb =25
C.
Symbol Parameter Conditions Min Typ Max Unit
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 14 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
11.3 Test circuits
Qinj charge injection CL= 0.1 nF; Vgen =0V; R
gen =0;
fi= 1 MHz; RL=1 M; see Figure 21
VCC =1.8V - 3.3 - pC
VCC =2.5V - 4.1 - pC
VCC =3.3V - 5.0 - pC
VCC =4.5V - 6.4 - pC
VCC =5.5V - 7.5 - pC
Table 12. Additional dynamic characte ristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); Tamb =25
C.
Symbol Parameter Conditions Min Typ Max Unit
Test conditions:
VCC = 1.65 V: Vi = 1.4 V (p-p).
VCC = 2.3 V: Vi = 2 V (p-p).
VCC = 3 V: Vi = 2.5 V (p-p).
VCC = 4.5 V: Vi = 4 V (p-p).
Fig 17. Test circuit for measuring total harmonic distorti on
DDP
9,+
92
9&& 9&&
=<<=
(
ȍIL
5/
)
&/'
Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads 3dB.
Fig 18. Test circuit for measuring the frequency response when switch is in ON-state
DDP
9,+
92
9&& 9&&
=<<=
(
ȍIL
5/
)
&/G%
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 15 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
Adjust fi voltage to obtain 0 dBm level at input.
Fig 19. Test circuit for measuring isolation (OFF -state)
DDP
9
,/
9
2
9
&&
9
&&
=<<=
(
ȍIL
5/
9
&&
5/
)
&/
G%
Fig 20. Test circuit for measuring crosstalk between digital input and switch
DDP
92
9&&
9&&
=<<=
(
ȍ ȍ
ORJLF
LQSXW 5/
9&&
&/
*
Qinj =VO CL.
VO = output voltage variation.
Rgen = generator resistance.
Vgen = generator voltage.
Fig 21. Test circuit for measuring charge injection
DDP
92
9&&
=<<=
(
ORJLF
LQSXW
5/
0ȍ
5JHQ
&/
Q)
9JHQ
*
DDP
RQRII
ORJLF
LQSXW(
9
2
RII
ǻ9
2
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 16 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
12. Package outline
Fig 22. Package outline SOT353-1 (TSSOP5)
81,7 $
$
PD[ $ $ ES /+( /S Z \Y
F H' ( = ș
5()(5(1&(6
287/,1(
9(56,21
(8523($1
352-(&7,21 ,668('$7(
,(& -('(& -(,7$
PP
H
',0(16,216PPDUHWKHRULJLQDOGLPHQVLRQV
1RWH
3ODVWLFRUPHWDOSURWUXVLRQVRIPPPD[LPXPSHUVLGHDUHQRWLQFOXGHG
627 02 6&$
Z 0
ES
'
=
H
H
ș
$
$
$
/S
$
GHWDLO;
/
+(
(
F
Y 0 $
;
$
\
PP
VFDOH
76623SODVWLFWKLQVKULQNVPDOORXWOLQHSDFNDJHOHDGVERG\ZLGWKPP 627
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 17 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
Fig 23. Package outline SOT753 (SC-74A)
5()(5(1&(6
287/,1(
9(56,21
(8523($1
352-(&7,21 ,668('$7(
,(& -('(& -(,7$
627 6&$
Z%0
ES
'
H
$
$
/S
4
GHWDLO;
+(
(
Y0$
$%
\
PP
VFDOH
F
;
3ODVWLFVXUIDFHPRXQWHGSDFNDJHOHDGV 627
81,7 $ESF'(+(/S4\ZY
PP
H
',0(16,216PPDUHWKHRULJLQDOGLPHQVLRQV
$
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 18 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
13. Abbreviations
14. Revision history
Table 13. Abbreviations
Acronym Description
CMOS Complementary Metal Oxide Semiconductor
DUT Device Under Test
ESD ElectroStatic Discharge
HBM Human Body Model
MIL Military
MM Machine Model
TTL Tr ansistor-Trans istor Logic
Table 14. Revision history
Document ID Release date Data sheet status Change notice Supersedes
74LV C1G66_Q100 v.2 20161209 Product data sheet - 74LVC1G66_Q100 v.1
Modifications: •Table 7: The maximum limits for leakage current and supply current have changed.
74LV C1G66_Q100 v.1 20120801 Prod uct data sheet - -
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 19 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
15. Legal information
15.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design.
[2] The term ‘short data sheet’ is explained in section “Definitions”.
[3] The product status of de vice(s) descr ibed in th is document m ay have cha nged since thi s document w as publish ed and may di ffe r in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nexperia.com.
15.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. Nexperia does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liab ility for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and tit le. A short data sh eet is intended
for quick reference only and shou ld not b e relied u pon to cont ain det ailed and
full information. For detailed and full informatio n see the relevant full data
sheet, which is available on request via the local Nexperia sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall pre va il.
Product specificatio n — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
Nexperia and its customer, unless Nexperia and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the Nexperia product is
deemed to off er functions and qualities beyond those described in the
Product data sheet.
15.3 Disclaimers
Limited warr a nty and liability — Information in this document is believed to
be accurate and reliable. However, Nexperia does not give any
representations or warrant ies, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. Nexperia takes no
responsibility for the content in this document if provided by an information
source outside of Nexperia.
In no event shall Nexperia be liable for any indirect, incidental,
punitive, special or consequ ential damages (including - wit hout limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, Nexperia’s aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of Nexperia.
Right to make changes — Nexperia reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all informa tion supplied prior
to the publication hereof .
Suitability for use in automotive applications — This Nexperia
product has been qualified for use in automotive
applications. Unless otherwise agreed in writing, the product is not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of a Nexperia product can reasonably be expected
to result in perso nal injury, death or severe property or environmental
damage. Nexperia and its suppliers accept no liability for
inclusion and/or use of Nexperia products in such equipment or
applications and t her efo re su ch inclu si on a nd/or use is at the cu stome r's own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. Nexperia makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and ope ration of their applications
and products using Nexperia products, and Nexperia
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the Nexperia
product is suitable and fit for the customer’s applications and
products planned, as well as fo r the planned application and use of
customer’s third party customer(s). Custo mers should provide appropriate
design and operating safeguards to minimize the risks associated with t heir
applications and products.
Nexperia does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party custo mer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using Nexperia
products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). Nexperia does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — Nexperia
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nexperia.com/profile/terms, unless otherwise
agreed in a valid written individua l agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. Nexperia hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of Nexperia products by customer.
Document status[1][2] Product status[3] Definition
Objective [short] data sheet Development This document contain s data from the objective specification for product develop ment.
Preliminary [short] dat a sheet Qualification This document contains data from the preliminary specification.
Product [short] data sheet Production This document contains the product specification.
© Nexperia B.V. 2017. All rights reserved
74LVC1G66_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 2 — 9 December 2016 20 of 21
Nexperia 74LVC1G66-Q100
Bilateral switch
No offer to sell or license — Nothing in this document may be interpret ed or
construed as an of fer to se ll product s that is op en for accept ance or the grant ,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
15.4 Trademarks
Notice: All referenced b rands, produc t names, service names and trademarks
are the property of their respective ow ners.
16. Contact information
For more information, please visit: http://www.nexperia.com
For sales office addresses, please send an email to: salesaddresses@nexperia.com
Nexperia 74LVC1G66-Q100
Bilateral switch
17. Contents
1 General description. . . . . . . . . . . . . . . . . . . . . . 1
2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1
3 Ordering information. . . . . . . . . . . . . . . . . . . . . 2
4 Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
5 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
6 Pinning information. . . . . . . . . . . . . . . . . . . . . . 3
6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
7 Functional description . . . . . . . . . . . . . . . . . . . 3
8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4
9 Recommended operating conditions. . . . . . . . 4
10 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5
10.1 Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
10.2 ON resistance. . . . . . . . . . . . . . . . . . . . . . . . . . 6
10.3 ON resistance test circuit and graphs. . . . . . . . 7
11 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9
11.1 Waveforms and test circuit . . . . . . . . . . . . . . . 10
11.2 Additional dynamic characteristics . . . . . . . . . 12
11.3 Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
12 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16
13 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 18
14 Revision history. . . . . . . . . . . . . . . . . . . . . . . . 18
15 Legal information. . . . . . . . . . . . . . . . . . . . . . . 19
15.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 19
15.2 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
15.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
15.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
16 Contact information. . . . . . . . . . . . . . . . . . . . . 20
17 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
© Nexperia B.V. 2017. All rights reserved
For more information, please visit: http://www.nexperia.com
For sales office addresses, please send an email to: salesaddresses@nexperia.com
Date of release:
09 December 2016
