ATC General Purpose Capacitors
Low Cost
Multilayer Ceramic Capacitors
For Surface Mount Applications
Manufactured for ATC
ATC 001-847
Rev. I; 5/06
2
ATC GENERAL PURPOSE CAPACITORS: NPO (COG) DIELECTRIC
ELECTRICAL CHARACTERISTICS
CAPACITANCE RANGE: 0.5 pF to 0.10 µF.
TEMPERATURE CHARACTERISTIC: 0 ± 30ppm/°C.
OPERATING TEMPERATURE RANGE: -55°C to +125°C.
DISSIPATION FACTOR:
0.1% (max.) @ + 25°C,
@1 MHz ≤1000 pF; @1 KHz >1000 pF
INSULATION RESISTANCE @ + 25°C and rated Vdc:
100,000 megohms (min.) or 1000 ohm-farads (min.),
whichever is less.
DIELECTRIC WITHSTANDING VOLTAGE:
250% of rated voltage for 5 ± 1 seconds, 50 milliamps (max.).
Unless otherwise specified all test data is at + 25°C.
T (MAX.)
MB
LW
Temperature Coefficient
Temperature (Celsius)
Temperature (Celsius)
Minimum IR vs. Temperature
Impedance vs. Frequency Dissipation Factor vs. Frequency
Aging Rate Voltage Coefficient of Capacitance
Sales of ATC products are subject to the terms and conditions contained in American Technical Ceramics Corp. Terms and Conditions of Sale(ATC document #001-992 Rev. A 10/03). Copies of
these terms and conditions will be provided upon request. They may also be viewed on ATC's website at www.atceramics.com/productfinder/default.asp. Click on the link for Terms and
Conditions of Sale.
ATC has made every effort to have this information as accurate as possible. However, no responsibility is assumed by ATC for its use, nor for any infringements of rights of third parties which
may result from its use. ATC reserves the right to revise the content or modify its product without prior notice.
© 1997 American Technical Ceramics. All Rights Reserved.
AMERICAN TECHNICAL CERAMICS
www.atceramics.com
ATC North America
631-622-4700 • sales@atceramics.com
ATC Europe
+46 8 6800410 • sales@atceramics-europe.com
ATC Asia
86-755-8366-4318 • sales@atceramics-asia.com
3
Dimensions shown in inches (mm) Higher voltages available upon request. *IR and Vapor Phase soldering only recommended.
ATC GENERAL PURPOSE CAPACITORS: NPO (COG) DIELECTRIC
PART NUMBER CODE
0603 NPO 1R 0 C T 2 A T
Size Code Packaging: T=7” Reel, B=Bulk
*R=13” Reel - *Special Order
Temperature Characteristic
Marking: A=No mark
Capacitance Code: First 2 Significant Digits For Capacity. *S=EIA Code - *Special Order
Indicates number of zeros following digits of capacitance in picofarads
R=Decimal Point
WVDC Code A 7
WVDC
10 16
*Special Order - Consult Factory
1
25
2
50
3
10 0*
4
200*
5
500*
6
1000*
8
2000*
9
5000*
Cap. Code Cap. pF
0R5 0.5
1R0 1.0
1R2 1.2
1R5 1.5
1R8 1.8
2R2 2.2
2R7 2.7
3R3 3.3
3R9 3.9
4R7 4.7
5R6 5.6
Cap. Code Cap. pF
6R8 6.8
8R2 8.2
100 10
120 12
150 15
180 18
220 22
270 27
330 33
390 39
470 47
Cap. Code Cap. pF
560 56
680 68
820 82
101 100
121 120
151 150
181 180
221 220
271 270
331 330
391 390
Cap. Code Cap. pF
471 470
561 560
681 680
821 820
102 1000
122 1200
152 1500
182 1800
222 2200
272 2700
332 3300
Cap. Code Cap. pF
392 3900
472 4700
562 5600
682 6800
822 8200
Cap. Code Cap.µF
103 .010
123 .012
153 .015
183 .018
223 .022
Cap. Code Cap.µF
273 .027
333 .033
393 .039
473 .047
563 .056
683 .068
823 .082
104 .10
124 .12
154 .15
184 .18
Cap. Code Cap. µF
224 .22
274 .27
334 .33
394 .39
474 .47
564 .56
684 .68
824 .82
105 1.0
125 1.2
155 1.5
Cap. Code Cap. µF
185 1.8
225 2.2
275 2.7
335 3.3
395 3.9
475 4.7
565 5.6
685 6.8
825 8.2
106 10.0
126 12.0
156 15.0
STANDARD EIA CAPACITANCE VALUES REFERENCE TABLE
SIZE
Length (L)
Width (W)
Tol. L & W
T Max.
Term. (MB) Min.
Max.
Min. Cap.
Max. Cap.
(code)
& WVDC
10V
16V
25V
50V
100V
200V
500V
1000V
2000V
5000V
0402
.040 (1.02)
.020 (0.51)
±.004 (0.10)
.025 (0.64)
.004 (.10)
.012 (.30)
0R5
271
331
221
101
680
0504
.050 (1.27)
.040 (1.02)
±.006 (.152)
.044 (1.12)
.005 (.12)
.015 (.38)
0R5
182
122
102
561
391
0603
.063 (1.60)
.031 (0.80)
±.005 (0.12)
.035 (0.89)
.005 (.12)
.015 (.38)
0R5
102
102
102
102
271
0805
.079 (2.00)
.049 (1.25)
±.008 (0.2)
.051 (1.30)
.010 (.25)
.028 (.71)
0R5
103
472
332
182
122
471
331
1206
.126 (3.20)
.063 (1.60)
±.008 (0.2)
.051 (1.30)
.010 (.25)
.028 (.71)
0R5
153
223
103
562
392
102
821
271
1210
.126 (3.20)
.098 (2.50)
±.008 (0.2)
.067 (1.70)
.010 (.25)
.028 (.71)
681
273
223
223
103
822
222
182
681
1812
.177 (4.50)
.126 (3.20)
±.010 (0.25)
.067 (1.70)
.010 (.25)
.030 (.76)
471
393
393
333
183
123
392
222
122
2225*
.220 (5.59)
.250 (6.35)
±.015 (0.38)
.070 (1.78)
.010 (.25)
.030 (.76)
102
104
104
104
683
473
153
103
472
CAPACITANCE TOLERANCE
Code B* C G* J
Tol. ±0.1 ±0.25 ±2 ±5
pF (Values < 10 pF) % (Values > 10 pF)
*Tighter tolerances available.
AMERICAN TECHNICAL CERAMICS
www.atceramics.com
ATC North America
631-622-4700 • sales@atceramics.com
ATC Europe
+46 8 6800410 • sales@atceramics-europe.com
ATC Asia
86-755-8366-4318 • sales@atceramics-asia.com
Termination Code
T = Tin plated over Nickel Barrier (Standard), RoHS Compliant
W = Tin/Lead, Solder Plated over Nickel Barrier**
C = Palladium Silver, (non-magnetic), RoHS Compliant**
**Consult ATC for availability
4
ATC GENERAL PURPOSE CAPACITORS: X7R DIELECTRIC
ELECTRICAL CHARACTERISTICS
CAPACITANCE RANGE: 220 pF to 2.2 µF.
TEMPERATURE CHARACTERISTIC: ± 15% with 0 Vdc applied.
OPERATING TEMPERATURE RANGE: -55°C to +125°C.
DISSIPATION FACTOR: 2.5% (max.) @ 25°C,
@1 MHz ≤1000 pF; @1 KHz >1000 pF
INSULATION RESISTANCE @ + 25°C and rated Vdc:
100,000 megohms (min.) or 1000 ohm-farads (min.), whichever is less.
DIELECTRIC WITHSTANDING VOLTAGE: 250% of rated voltage
for 5 ± 1 seconds, 50 milliamps (max.).
AGING RATE: 1% (maximum) per decade.
Unless otherwise specified all test data is at + 25°C.
Temperature Coefficient of Capacitance
Minimum IR vs. Temperature Impedance vs. Frequency
Dissipation Factor vs. Temperature Voltage Coefficient of Capacitance
Temperature (Celsius)
Temperature (Celsius)
Temperature (Celsius)
T (MAX.)
MB
LW
AMERICAN TECHNICAL CERAMICS
www.atceramics.com
ATC North America
631-622-4700 • sales@atceramics.com
ATC Europe
+46 8 6800410 • sales@atceramics-europe.com
ATC Asia
86-755-8366-4318 • sales@atceramics-asia.com
Dimensions shown in inches (mm) *IR and Vapor Phase soldering only recommended.
ATC GENERAL PURPOSE CAPACITORS: X7R DIELECTRIC
SIZE
Length (L)
Width (W)
Tol. L & W
T Max.
Term. (MB) Min.
Max.
Min. Cap.
Max. Cap.
(code)
& WVDC
10V
16V
25V
50V
100V
200V
500V
1000V
2000V
5000V
0402
.040 (1.02)
.020 (0.51)
±.004 (0.10)
.025 (0.64)
.004 (.10)
.012 (.30)
121
104
273
103
272
182
0504
.050 (1.27)
.040 (1.02)
±.006 (.152)
.044 (1.12)
.005 (.12)
.015 (.38)
221
393
273
273
153
103
0603
.063 (1.60)
.031 (0.80)
±.005 (0.12)
.035 (0.89)
.005 (.12)
.015 (.38)
331
224
104
104
103
682
0805
.079 (2.00)
.049 (1.25)
±.008 (0.2)
.051 (1.30)
.010 (.25)
.028 (.71)
471
475
335
474
224
563
333
103
272
1206
.126 (3.20)
.063 (1.60)
±.008 (0.2)
.051 (1.30)
.010 (.25)
.028 (.71)
102
334
274
474
154
823
273
682
102
1210
.126 (3.20)
.098 (2.50)
±.008 (0.2)
.067 (1.70)
.010 (.25)
.028 (.71)
102
684
564
105
105
184
563
153
222
1812
.177 (4.50)
.126 (3.20)
±.010 (0.25)
.067 (1.70)
.010 (.25)
.030 (.76)
122
125
105
225
105
334
104
273
392
2225*
.220 (5.59)
.250 (6.35)
±.015 (0.38)
.070 (1.78)
.010 (.25)
.030 (.76)
183
225
185
335
225
105
334
124
183
Cap. Code Cap. pF
0R5 0.5
1R0 1.0
1R2 1.2
1R5 1.5
1R8 1.8
2R2 2.2
2R7 2.7
3R3 3.3
3R9 3.9
4R7 4.7
5R6 5.6
Cap. Code Cap. pF
6R8 6.8
8R2 8.2
100 10
120 12
150 15
180 18
220 22
270 27
330 33
390 39
470 47
Cap. Code Cap. pF
560 56
680 68
820 82
101 100
121 120
151 150
181 180
221 220
271 270
331 330
391 390
Cap. Code Cap. pF
471 470
561 560
681 680
821 820
102 1000
122 1200
152 1500
182 1800
222 2200
272 2700
332 3300
Cap. Code Cap. pF
392 3900
472 4700
562 5600
682 6800
822 8200
Cap. Code Cap.µF
103 .010
123 .012
153 .015
183 .018
223 .022
Cap. Code Cap.µF
273 .027
333 .033
393 .039
473 .047
563 .056
683 .068
823 .082
104 .10
124 .12
154 .15
184 .18
Cap. Code Cap. µF
224 .22
274 .27
334 .33
394 .39
474 .47
564 .56
684 .68
824 .82
105 1.0
125 1.2
155 1.5
Cap. Code Cap. µF
185 1.8
225 2.2
275 2.7
335 3.3
395 3.9
475 4.7
565 5.6
685 6.8
825 8.2
106 10.0
126 12.0
156 15.0
STANDARD EIA CAPACITANCE VALUES REFERENCE TABLE
5
PART NUMBER CODE
0805 X7R 10 2 K T 2 A T
Size Code Packaging: T=7” Reel, B=Bulk
*R=13” Reel - *Special Order
Temperature Characteristic
Marking: A=No mark
Capacitance Code: First 2 Significant Digits For Capacity. *S=EIA Code - *Special Order
Indicates number of zeros following digits of capacitance in picofarads
CAPACITANCE TOLERANCE
Code *J K
Tol. ±5 ±10
*Tighter tolerances available.
WVDC Code A 7
WVDC
10 16
*Special Order - Consult Factory
1
25
2
50
3
10 0*
4
200*
5
500*
6
1000*
8
*2000
9
*5000
AMERICAN TECHNICAL CERAMICS
www.atceramics.com
ATC North America
631-622-4700 • sales@atceramics.com
ATC Europe
+46 8 6800410 • sales@atceramics-europe.com
ATC Asia
86-755-8366-4318 • sales@atceramics-asia.com
Termination Code
T = Tin plated over Nickel Barrier (Standard), RoHS Compliant
W = Tin/Lead, Solder Plated over Nickel Barrier**
C = Palladium Silver, (non-magnetic), RoHS Compliant**
**Consult ATC for availability
6
ATC GENERAL PURPOSE CAPACITORS: Z5U DIELECTRIC
ELECTRICAL CHARACTERISTICS
CAPACITANCE RANGE: .01 µF to 15 µF.
TEMPERATURE CHARACTERISTIC: +22%, -56%
OPERATING TEMPERATURE RANGE: +10°C to +85°C.
DISSIPATION FACTOR: 3.5% (max.) @ 25°C,
@ 1 KHz.
INSULATION RESISTANCE @ + 25°C and rated Vdc:
100 ohm-farads (min.).
DIELECTRIC WITHSTANDING VOLTAGE:
250% of rated voltage for 5 ± 1 seconds, 50 milliamps (max.).
AGING RATE: 3% (maximum) per decade.
Unless otherwise specified all test data is at + 25°C.
Temperature Coefficient of Capacitance
Minimum IR vs. Temperature
Dissipation Factor vs. Temperature Voltage Coefficient of Capacitance
Impedance vs. Frequency
Temperature (Celsius)
Temperature (Celsius)
Temperature (Celsius)
T (MAX.)
MB
LW
AMERICAN TECHNICAL CERAMICS
www.atceramics.com
ATC North America
631-622-4700 • sales@atceramics.com
ATC Europe
+46 8 6800410 • sales@atceramics-europe.com
ATC Asia
86-755-8366-4318 • sales@atceramics-asia.com
ATC GENERAL PURPOSE CAPACITORS: Z5U DIELECTRIC
Dimensions shown in inches (mm) *IR and Vapor Phase soldering only recommended.
PART NUMBER CODE
1206 Z5U 10 4 M T 2 A T
Size Code Packaging: T=7” Reel, B=Bulk
*R=13” Reel - *Special Order
Temperature Characteristic
Marking
Capacitance Code: First 2 Significant Digits For Capacity. A=No mark
*S=EIA Code - *Special Order
Indicates number of zeros following
digits of capacitance in picofarads
CAPACITANCE TOLERANCE
Code M Z
Tol. ±20 +80 -20
%
WVDC Code A 7
WVDC
10 16
*Special Order - Consult Factory
1
25
2
50
3
10 0*
4
200*
SIZE
Length (L)
Width (W)
Tol. L & W
T Max.
Term. (MB) Min.
Max.
Min Cap
Max. Cap.
(code)
& WVDC
10V
16V
25V
50V
100V
200V
0603
.063 (1.60)
.031 (0.80)
±.005 (0.12)
.035 (0.89)
.005 (.12)
.015 (.38)
562
154
104
683
273
562
0805
.079 (2.00)
.049 (1.25)
±.008 (0.2)
.051 (1.30)
.010 (.25)
.028 (.71)
103
684
474
334
124
333
1206
.126 (3.20)
.063 (1.60)
±.008 (0.2)
.051 (1.30)
.010 (.25)
.028 (.71)
223
155
125
105
274
823
1210
.126 (3.20)
.098 (2.50)
±.008 (0.2)
.067 (1.70)
.010 (.25)
.028 (.71)
333
335
225
185
564
184
1812
.177 (4.50)
.126 (3.20)
±.010 (0.25)
.067 (1.70)
.010 (.25)
.030 (.76)
154
565
475
395
125
394
2225*
.220 (5.59)
.250 (6.35)
±.015 (0.38)
.070 (1.78)
.010 (.25)
.030 (.76)
105
106
106
825
225
684
Cap. Code Cap. pF
0R5 0.5
1R0 1.0
1R2 1.2
1R5 1.5
1R8 1.8
2R2 2.2
2R7 2.7
3R3 3.3
3R9 3.9
4R7 4.7
5R6 5.6
Cap. Code Cap. pF
6R8 6.8
8R2 8.2
100 10
120 12
150 15
180 18
220 22
270 27
330 33
390 39
470 47
Cap. Code Cap. pF
560 56
680 68
820 82
101 100
121 120
151 150
181 180
221 220
271 270
331 330
391 390
Cap. Code Cap. pF
471 470
561 560
681 680
821 820
102 1000
122 1200
152 1500
182 1800
222 2200
272 2700
332 3300
Cap. Code Cap. pF
392 3900
472 4700
562 5600
682 6800
822 8200
Cap. Code Cap.µF
103 .010
123 .012
153 .015
183 .018
223 .022
Cap. Code Cap.µF
273 .027
333 .033
393 .039
473 .047
563 .056
683 .068
823 .082
104 .10
124 .12
154 .15
184 .18
Cap. Code Cap. µF
224 .22
274 .27
334 .33
394 .39
474 .47
564 .56
684 .68
824 .82
105 1.0
125 1.2
155 1.5
Cap. Code Cap. µF
185 1.8
225 2.2
275 2.7
335 3.3
395 3.9
475 4.7
565 5.6
685 6.8
825 8.2
106 10.0
126 12.0
156 15.0
STANDARD EIA CAPACITANCE VALUES REFERENCE TABLE
7
AMERICAN TECHNICAL CERAMICS
www.atceramics.com
ATC North America
631-622-4700 • sales@atceramics.com
ATC Europe
+46 8 6800410 • sales@atceramics-europe.com
ATC Asia
86-755-8366-4318 • sales@atceramics-asia.com
Termination Code
T = Tin plated over Nickel Barrier (Standard), RoHS Compliant
W = Tin/Lead, Solder Plated over Nickel Barrier**
C = Palladium Silver, (non-magnetic), RoHS Compliant**
**Consult ATC for availability
ATC 0603
APPLICATION NOTES
TERMINATION STYLES
T = RoHS Compliant Tin plated over Nickel
Barrier (Standard)
W = Tin/Lead, Solder Plated over Nickel Barrier**
C = Palladium Silver, RoHS Compliant
(non-magnetic)
**Consult ATC for availability
RECOMMENDED
SOLDERING PROFILES
• A mildly activated rosin flux 'RMA' is
recommended.
• Sn60 (60% Sn, 40% Pb) or Sn62 (62.5% Sn,
36.1% Pb, 1.4% Ag) are recommended.
• Sizes 2225 and larger should be re-flow or
vapor phase soldered. Wave solder is not
recommended on these larger sizes.
• Tape and reel packaging is
preferred and is available for all sizes.
• To specify 7" reel use "T" in part
number code.
• For 13" reel use "R" in part number
code.
• Parts are packaged per EIA-RS481
specification.
• For tape size and approximate
quantity per reel consult factory.
POST ASSEMBLY
COOLDOWN AND
CLEANING
• Allow assembly to cool to room temperature.
Do not attempt to speed up cooldown cycle as
thermal cracking may result.
• Cleaning solvents are dependant on materials
and flux type used. Multi-stage cleaning in
alcohol, water, hydrocarbons, and common
degreaser solvents will not damage our chip
capacitors.
SOLDERING TECHNIQUES
The reflow, vapor phase, and wave soldering
profiles shown are recommended. Hand
soldering is not preferred but can be
accomplished successfully if the following
precautions are followed:
• Use a low wattage iron with correct size tip.
• A preheat of 150°C minimum is
recommended.
• Do not exceed 280°C maximum.
• Apply heat thru the solder. Minimize the
contact to termination metalization.
• Keep the soldering process as short as
possible.
ATC CROSS REFERENCE GUIDE
250 Entrance - Preheat Reflow Zone
Time - Minutes
Vapor Phase Soldering
Cool Down Zone
Temperature (Celsius)
215
200
150
100
50
001 2345
Soldering Zone Range Recommended Area
300 Preheat Zone
Time - (Seconds)
Reflow Soldering
Cooling Zone
Temperature (Celsius)
250
220
200
150
100
50
0
020 40 60 80 100 120 140 160 180 200
Soldering Zone Range Recommended Area
Soldering Time
Max. 7 Seconds
Air Cooling
25 C
300 Preheat Zone
Time - (Seconds)
Wave Soldering
Cooling Zone
Temperature (Celsius)
250
260
200
150
100
50
0020 40 60 80 100 120 140 160 180 200
Soldering Zone Range Recommended Area
Soldering Time
Max. 5 Seconds
Air Cooling
25 C
ATC SERIES DESCRIPTION AVX
(KYOCERA) KEMET JOHANSON MURATA NOVACAP PANASONIC PHILLIPS TDK VITRAMON
ATC 0805
EIA 0805 SIZE,
NICKEL BARRIER
TERMINATIONS NPO, X7R, Z5U
0805 C0805 R15 GRM40 0805 ECU (N) CXXXX0805 CC0805 VJ0805
ATC 1206
EIA 1206 SIZE,
NICKEL BARRIER
TERMINATIONS NPO, X7R, Z5U
1206 C1206 R18 GRM42-6 1206 ECU (M) CXXXX1206 CC1206 VJ1206
ATC 1210
EIA 1210 SIZE,
NICKEL BARRIER
TERMINATIONS NPO, X7R, Z5U
1210 C1210 S41 GRM42-2 1210 EPU (P) CXXXX1210 CC1210 VJ1210
ATC 0402
EIA 0402 SIZE,
NICKEL BARRIER
TERMINATIONS NPO, X7R
0402 C0402 R07 GRM36 0402 ECU (Q) CXXXX0402 CC0402 VJ0402
EIA 0603 SIZE,
NICKEL BARRIER
TERMINATIONS NPO, X7R, Z5U
0603 C0603 R14 GRM39 0603 _ CXXXX0603 CC0603 VJ0603
TAPE AND REEL PACKAGING FOR AUTOMATIC INSERTION
ATC 1812
EIA 1812 SIZE,
NICKEL BARRIER
TERMINATIONS NPO, X7R, Z5U
1812 C1812 S43 GRM43-2 1812 – – – VJ1812
ATC 2225
EIA 2225 SIZE,
NICKEL BARRIER
TERMINATIONS NPO, X7R, Z5U
2225 C2225 S48 – 2225 – – – VJ2225
ATC 001-847 Rev. I; 5/06
AMERICAN TECHNICAL CERAMICS
www.atceramics.com
ATC North America
631-622-4700 • sales@atceramics.com
ATC Europe
+46 8 6800410 • sales@atceramics-europe.com
ATC Asia
86-755-8366-4318 • sales@atceramics-asia.com
